Page 3 - Installation
ThinkServer RD220 Types 3729, 3779, 3797, and 3798 Installation and User Guide
Page 5 - Contents; iii
Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . 1 Notices and statements in this document . . . . . . . . . . . . . . . . 2 Related documentation . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2. S...
Page 6 - iv
Removing a PCI adapter . . . . . . . . . . . . . . . . . . . . . 54 Installing a PCI adapter . . . . . . . . . . . . . . . . . . . . . . 56 Installing the full-length-adapter bracket . . . . . . . . . . . . . . . . 60 Storing the full-length-adapter bracket . . . . . . . . . . . . . . . . 60 Removin...
Page 8 - Index
Battery return program . . . . . . . . . . . . . . . . . . . . . 159 German Ordinance for Work gloss statement . . . . . . . . . . . . . 160 Electronic emissions notices . . . . . . . . . . . . . . . . . . . 160 Federal Communications Commission (FCC) statement . . . . . . . . 160 Industry Canada Cl...
Page 9 - Safety; vii
Safety Before installing this product, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí. Læs sikkerhedsforskrifterne, før du installerer dette produkt. Lees voordat u dit produc...
Page 10 - viii
Important: Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document. For example, if a caution sta...
Page 11 - ix
Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a ...
Page 13 - xi
Statement 3: CAUTION: When laser products (such as CD drives, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable part...
Page 14 - xii
Statement 4: ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might hav...
Page 15 - xiii
Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a prob...
Page 16 - xiv
This server is suitable for use on an IT power-distribution system whose maximum phase-to-phase voltage is 240 V under any distribution fault condition. Important: This product is not suitable for use with visual display workplace devices according to Clause 2 of the German Ordinance for Work with V...
Page 23 - Features; server
Chapter 3. What is included with your server The RD220 server package includes the server, rail kit and rail kit instructions, as well as printed documentation, the ThinkServer Documentation DVD, and software media. 1 Power cord 2 Cable management arm 3 Rail kit 4 Server Features and technologies Th...
Page 26 - Specifications
running on the server and TOE is enabled, the server supports TOE operation. See the operating-system documentation for information about enabling TOE. Note: As of the date of this document, the Linux operating system does not support TOE. Specifications The following information is a summary of the...
Page 31 - Front
Chapter 4. Server controls, LEDs, and power This section describes the controls and light-emitting diodes (LEDs) and how to turn the server on and off. Front view The following illustration shows the controls, light-emitting diodes (LEDs), and connectors on the front of the server. 1 Hard disk drive...
Page 34 - Reset
There are two types of checkpoint codes: field programmable gate array (FPGA) hardware checkpoint codes and UEFI checkpoint codes. The UEFI checkpoint codes might change because of code sequence and timing changes or when the server firmware is updated. v Reset button: Press this button to reset the...
Page 38 - Ethernet
Rear view The following illustration shows the connectors and LEDs on the rear of the server. 1 Ethernet 3 (optional) connector 7 USB 3 connector 2 Ethernet 4 (optional) connector 8 Serial connector 3 Power supply 1 connector 9 Video connector 4 Power supply 2 connector 10 Ethernet 2 connector 5 Pow...
Page 40 - internal
Fading on and off: The server is in a reduced-power state. To wake the server, press the power-control button or use the IMM Web interface. For information about logging on to the IMM Web interface, see “Logging on to the Web interface” on page 125. System-board internal connectors The following ill...
Page 43 - Clear; LEDs
Table 4. Callout descriptions (continued) Notes: 1. If no jumper is present, the server responds as if the pins are set to 1 and 2. 2. Changing the position of the UEFI boot recovery jumper from pins 1 and 2 to pins 2 and 3 before the server is turned on alters which flash ROM page is loaded. Do not...
Page 44 - SAS
Note: Error LEDs remain lit only while the server is connected to power. Table 6. Callout descriptions 1 PCI riser 2 LED 13 Fan 3 error LED 2 Enclosure manager heartbeat LED 14 Power channel A LED 3 Battery error LED 15 Power channel B LED 4 IMM heartbeat LED 16 Power channel C error LED 5 PCI riser...
Page 47 - For
Power-supply LEDs The following illustration shows the power-supply LEDs on the rear of the server. For more information about solving power-supply problems, see the Hardware Maintenance Manual . 1 AC power LED (green) 2 DC power LED (green) 3 Power-supply error LED (amber) Server power features Whe...
Page 59 - Installing
1 PCI riser-card assembly 2 2 PCI riser-card assembly 1 To remove the riser-card assembly, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 33. 2. Turn off the server and peripheral devices, and disconnect the power cord and a...
Page 108 - Removing
1 Tape drive 2 Tray 3 Latch 3. Prepare the drive according to the instructions that come with the drive, setting any switches or jumpers. 4. Slide the tape-drive assembly most of the way into the tape-drive bay. 5. Using the cables from the former tape drive, connect the signal and power cables to t...
Page 123 - Passwords; password
– Power-on Password Select this choice to set or change a power-on password. See “Power-on password” for more information. – Administrator Password Select this choice to set or change an administrator password. An administrator password is intended to be used by a system administrator; it limits acc...
Page 125 - Using; USB
Attention: Before changing any switch settings or moving any jumpers, turn off the server; then, disconnect all power cords and external cables. See the safety information that begins on page vii. Do not change settings or move jumpers on any system-board switch or jumper blocks that are not shown i...
Page 130 - DVD
Auto Configuration and Redundancy This mode automatically creates an optimal RAID 1 or RAID 5 configuration, providing data redundancy. Auto Configuration without Redundancy This mode automatically created a non-redundant RAID 0 configuration. 5. Click Next to continue. Viewing and changing adapter ...
Page 154 - problems; Power
Optional-device problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field...
Page 164 - diagnostics
Table 15. EasyLED panel LEDs (continued) LED Description Action CPU A microprocessor has failed. 1. Make sure that the failing microprocessor, which is indicated by a lit LED on the system board, is install correctly. 2. (Trained service technician only) Replace the microprocessor. DASD A hard disk ...
Page 169 - Warranty
Service methods and procedures vary by country, and some services might not be available in all countries. International Warranty Service is delivered through the method of service (such as depot, carry-in, or on-site service) that is provided in the servicing country. Service centers in certain cou...
Page 174 - Remarque
Remarque : Cette marque s’applique uniquement aux pays de l’Union Européenne et à la Norvège. L’etiquette du système respecte la Directive européenne 2002/96/EC en matière de Déchets des Equipements Electriques et Electroniques (DEEE), qui détermine les dispositions de retour et de recyclage applica...