Lennox T150C - Manual

PLANNING YOUR INSTALLATION PAGE 5 FLOOR PROTECTION This appliance requires ½" (13 mm) minimum non-combustible floor protection designed for solid fuel burn-ing appliances having a thermal conductivity of k = .84BTU in/ft or equivalent. If the floor protection is to bestone, tile, brick, etc., it...

PLANNING YOUR INSTALLATION PAGE 6 SELECTING A LOCATION The design of your home and where you place yourstove will determine its value as a source of heat. Awoodstove depends primarily on air circulation (convec-tion) to disperse its heat, and therefore, a central loca-tion is often best. There are o...

PLANNING YOUR INSTALLATION INSTALLATION PAGE 7 REDUCED MASONRY STRUCTURE CLEARANCE (ALCOVE) Your stove can be installed in a masonry structure with reduced clearances if the structure was built to National Building Code for fireplaces and chimneys (UBC 37). The firebox of the masonry structure must ...

INSTALLATION PAGE 8 TYPES OF CHIMNEYS The chimney is a vital part of your stove installation. Aproperly built masonry chimney or a properly installedfactory built chimney will assure a consistent draft undera variety of weather conditions (a smoking stove is usu-ally caused by a chimney problem). Th...

INSTALLATION PAGE 9 CHIMNEY HEIGHT REQUIREMENTS The chimney must extend 3 feet (914 mm) above thelevel of roof penetration and a minimum of 2 feet (610mm) higher than any roof surface within 10 feet (305 cm)(see below). Check with your local building officials forany additional requirements for your...

INSTALLATION PAGE 10 RESIDENTIAL INSTALLATION DIAGRAM

INSTALLATION Combustible Wall Chimney Connector Pass-Throughs NOTES:1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the wall pass-through systemand the chimney wall, to but not past the inner flue liner face. 2. A chimney connector shall not pas...

PRODUCT FEATURES AND CONTROLS PAGE 12 PRIMARY AIR CONTROL The primary combustion air delivery is controlled by thePrimary Air Control Assembly (The control knob is lo-cated above the fuel door). The heat output can be con-trolled by sliding the handle to a higher or lower heatoutput setting (See Car...

CARE AND OPERATION PAGE 13 FUEL DOOR CAUTION: WHEN OPENING THE DOOR, DO NOT EX-TEND IT BEYOND ITS NORMAL TRAVEL. OVEREX-TENDING THE DOOR TO A FURTHER OPEN POSITIONCAN PUT EXCESSIVE STRESS ON HINGE AREA OFDOOR AND HINGE PINS AND MAY RESULT IN BREAK-AGE. DOOR OPERATION The door handle assembly opens a...

CARE AND OPERATION PAGE 14 BREAK-IN PERIOD Your stove finish is a high temperature paint that requirestime and temperature to completely cure. W e recom-mend that you ventilate the house during the initial burns.The paint emits non-toxic odors during this process. KEEP YOUR HOUSE WELL VENTILATED DUR...

CARE AND OPERATION PAGE 15 Refueling *1. Open the damper bypass control by pulling it towardyou. 2. Set the primary air control set to high. 3. Open the door approximately 1/2 inch (13 mm),then wait for about thirty seconds. Open the doorand add wood, then close the door. 4. If the optional temperat...

FUEL PAGE 16 BURN RECOMMENDED FUEL This appliance is approved for use with untreated naturaldry wood only (see Important Warnings , page 2, #8). Burning materials other than natural wood will shorten thelife of the catalytic combustor. Do not burn particleboard orpressed logs using bonding agents as...

MAINTENANCE PAGE 17 SMALL AREA PAINT TOUCH-UP The stove body is painted with a quality high- temperature stove paint. Use only model TSPK-B Stove Paint, Catalog # 70K99. Do not touch-up your stove with any other paint. Using one small piece of 320 grit sand paper and lightly sand the blemish so that...

MAINTENANCE PAGE 18 CREOSOTE FORMATION AND NEED FOR RE-MOVALWhat is Creosote - W hen wood is burned slowly, it produces tar and other organic vapors, which combinewith expelled moisture to form creosote. The creosotevapors condense in the relatively cool chimney flue of aslow-burning fire. As a resu...

TROUBLESHOOTING PAGE 20 SMOKES OUT FUEL DOOR WHEN OPEN (see ✸ ✸ ✸ ✸ ) 1. The primary air control is closed.2. The chimney is too cool. Set the primary air control on "HIGH" with the bypass damper control "OPEN"for a few minutes before opening the fuel door. 3. Excess creosote will no...

SPECIFICATIONS: Model T150C PAGE 22 Approximate Up to ~1800 sq. ft. Heat Capacity Up to ~550 sq. M Maximum Burn Rate 49,027 BTU EPA BTU Range 6500 / 35,300 BTU Emissions Rate (grams/hr.) 4.1 Efficiency Rating 72% Outside Air Provision No Maximum Log Length 22" (559 mm) Firebox Size (cubic feet) ...

REPLACEMENT PARTS FOR MODEL: T150C PAGE 23 Part No. Model Description Door Parts C15220 Door Assembly, Cast (Handle Included) 27M83 Gasket Kit, 1/2" Medium Rope 26M23 Gasket Kit, Side W indow 1/8" Lytherm ⊗ 27M81 Gasket Kit, Door Glass Channel 18280 Glass, Door 9 5/8 X 14 1/4" (Glass gas...

COMPONENT DIAGRAMS: T150C PAGE 24 FIREBRICK (1 ¼” thick) Part Qty Dimensions FB-1 9 9 x 4 ¼” Regular Top View Showing Brick Installed CATALYTIC COMBUSTOR System Components

OPTIONAL ACCESSORIES: T150C Note: Install and use accessories per instructions provided with the accessory kit. PAGE 25 Catalog # Model Description Notes 14M36 BK-T15 Blower Kit Includes Dial-A-Temp for VariableSpeed Control 14M21 SSK Stove Stat Kit Thermally Con-trols Blower 14M34 MKT15-GRY Marble ...