Lennox RAD22C-2 - Manual

GENERAL INFORMATION

Note:

Do not operate fireplace without the eyebrow installed in its normal

position. See

Figure 1

for models with louvers or

Figure 2

for

models with clean face panel.

Step 1.

Grasp the existing eyebrow and pull it forward away from the

fireplace (it is held in place by spring tension). See

Figure 1

.

Step 2.

Slightly lift and pull the existing top louver assembly away from

the fireplace.

Step 3.

Slide the existing eyebrow into the slots on the lower edge of the

top radiant replacement panel.

Step 4.

Hang the top radiant panel/eyebrow assembly in the opening

previously occupied by the top louver assembly. See

Figure 2

.

Step 5.

Open the bottom louver assembly by pushing in simultaneously

the left and right sides of the louver assembly (the assembly is

hinged at the bottom).

Step 6.

Merit Series Units - Remove the assembly from the fireplace by

removing the hinge screw and spacer on each end of it.

Merit Plus and Elite Series Units - Remove the assembly from the

fireplace by sliding the hinge pin, located at the door’s left side,

to the right until it disengages from the left corner post hole. Pull

the door diagonally to the left, away from the fireplace.

Step 7.

Snap the replacement Lennox nameplate logo into the 2 holes

provided in the replacement panel.

Step 8.

Merit Series Units - Install the replacement bottom radiant panel

using the existing hinge screws and spacers.

Merit Plus and Elite Series Units - Install the replacement bottom

radiant panel by inserting the right side locating pin into the right

cabinet corner post and then the left side spring-loaded pin into

the left cabinet corner post.

These clean face panel kits may be used with Merit

™

, Merit Plus

™

or

Elite® series gas fireplaces listed in

Table 1.

INSTALLATION INSTRUCTIONS FOR CLEAN FACE PANEL KITS FOR USE WITH

MERIT

™,

MERIT PLUS

™

OR ELITE

®

SERIES GAS FIREPLACES

INSTALLATION INSTRUCTIONS

CLEAN FACE PANEL KITS

(PAINTED FINISH)

P/N 504,223M

REV. F 03/2008

LENNOX HEARTH PRODUCTS

KITS AND ACCESSORIES

Printed in U.S.A. © 2001 by Lennox Hearth Products

P/N 504,223M REV. F 03/2008

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Lennox Hearth Products

1110 West Taft Avenue • Orange, CA 92865

Figure 2 - Clean Face

Hood must be installed as shown.

Top of Appliance

Louver Assembly

Top of Door Frame

Figure 1 - Louvered Face

CAT. NO.

MODEL

WHERE USED

88L36

RAD35C-2

EDV3530, ED3530 front-open, MPD3530,

MPD35ST/PF, MPB35ST

88L37

RAD40C-2

EDV4035, ED4035-2, MPD4035 front open,

EDVST, EDST-2, EDVPF, EDPF-2, EDVCR,

EDCR-2, EDVCL, EDCL-2, EBST-2, EBVPF,

EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2

multi-open (long panel)

88L38

RAD45C-2

EDV4540, ED4540-2, MPD4540 front-open

88L35

RAD24C-2

EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,

EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2,

EBVCL, EBCL-2 multi-open (short panel)

98L12

RAD33C

MDR3328, MDT3328, MPDT3328,

MPDR3328

26M47

RAD33MC

MPD3530, MPD35ST

H7019

RAD22C-2

MPD35PF

Table 1 - Painted Panel Kits

KIT CONTENTS:

TOOLS REQUIRED:

1 ea. Top Radiant Panel

1 ea. Bottom Radiant Panel

1 ea. Lennox Nameplate

1 ea. Instruction Sheet

None

CAUTION

INSTALL ONLY WHEN THE

FIREPLACE IS OFF AND COLD!

Hood must be installed as shown.

Top of Appliance

Top Radiant Panel

Top of Door Frame

Top Radiant Panel

Bottom Radiant Panel

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products.

Consult your local distributor for fireplace code information.