Lennox PS40 - Manual

6 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. h earth p rotection The floor protector must be a non-combustible material extending beneath the stove and to the front and sides as shown below. Minimum Size Hearth Protection v ent t ermination r equirements 1. Do not terminate the vent in any...

7 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. Vent Installation v ent t ermination L ocations A = Clearance above grade, veranda, porch, deck, or bal- cony (min. 12”/30cm) B = Clearance to window or door that may be opened (min. 12”/30cm above - 48”/1.2m below and to the side) C = Clearance...

11 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. Door Trim Installation Instructions Parts List (A): Qty (2) Trim Pieces (Gold, Nickel, Brushed Nickel or Black Nickel ) (6) #10 nuts (6) #10 washers Tools Needed: Qty (1) 3/8” nut driver or socket wrench CAUTIoN: Always ensure that plated surfa...

1 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. 4. Place one washer on each stud. Using a 3/8” nut driver, snug up the nuts on each piece of trim. Do not finish tightening the nuts yet. See Figure 27. 5. There should be approximately a 7/8” (22mm) gap between the top edge of the upper trim an...

1 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. Door Grill Installation Instructions Parts Needed: Qty (4) Button Head Screws (already in place in stove) Tools Required: Qty (1) 1/8” allen wrench To install the Grill: 1. Remove the four button head screws from body of the stove with a 1/8” al...

1 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. Note: The brick panel comes pre-painted with Metallic black paint. The brick panel may be painted with any color of Stove bright® high-temp paint (paint may dis- color with use). 1. Remove the front door of the pellet stove. To remove the front ...

16 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. Log Set installation Instructions Kit Contents (A): Part #H51 Qty (1) left log (B) (1) right log (C) (1) front log (D) (2) log support brackets (E) A - Kit Contents cut lines b C D b C D e bracket in place correctly e figure 8 figure 9 figure 1...

17 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. operation c ontroL b oard The control board regulates all functions of the stove. The following is a list of the board’s components: • feeding light - lights up when the auger is feeding pellets into the burn pot. • Ready Light - lights up when...

19 NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. Cleaning and Maintenance Unplug and let the Winslow™ PS40 stove cool before per- forming any maintenance or cleaning. Some brands of pellets produce more ash and clinkers than others. Therefore the frequency of performing the following cleaning...

NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. F ront d oor r emovaL Caution: Do not open the front door when the stove is hot. To remove the door, swing the left and right side doors A open. Pull the front door handle B to the front and swing the front door open. Lift the front door up and of...

NoTe: DIAGRAMS & ILLUSTRATIoNS ARe NoT To SCALe. d raFt a djuster The Winslow™ PS40 stove has a draft adjuster located at the left side of the stove directly in front of the combustion blower. Should the stove installation require long runs of vent pipe, a situation may be created where excessiv...

5 d iagnostic c odes If the stove operates abnormally, the ready light on the control board will signal the nature of the abnormal operation. The following is a list of possible signals or codes: Ready light is constant red Ignition failure Ready light flashes red 1 short and 1 long blink Vacuum Swi...