Learning Resources LER 4411 X200 - Manual

LER 4411

X10~X200 1.3 MP Digital Microscope

Please Read All Instructions Carefully Before Using

User Guide

Twist

™

User Guide

Twist

™

User Guide

Twist

™

User Guide

Twist

™

User Guide

Twist

™

User Guide

Twist

™

User Guide

Twist

™

User Guide

2

4

6

8

3

5

7

•   Please retain these instructions for future reference.
•   Do not allow your Twist

™

 to come into contact with 

water or other liquids.

•   In the event of an electro-static discharge, your Twist

™

may malfunction. In this case, you may need to 
disconnect from the computer to reset it.

•   Warranty is void if the case is opened for any reason.
•   The warranty does not cover any data loss from the 

unit nor any consequential loss of information.

FCC compliance
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY 
RADIO OR T V INTERFERENCE CAUSED BY 
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. 
SUCH MODIFICATIONS COULD VOID THE USER’S 
AUTHORITY TO OPERATE THE EQUIPMENT
NOTE: This equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against 
harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 

interference to radio communications. However, there is 
no guarantee that interference will not occur in a 
particular installation.
If this equipment does cause harmful interference to 
radio or television reception, which can be determined 
by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or 
more of the following measures:
•   Reorient or relocate the receiving antenna 
•   Increase the separation between the equipment 

and receiver 

•   Connect the equipment into an outlet on a circuit 

different from that to which the receiver is connected 

•   Consult the dealer or an experienced radio/ T V 

technician for help

Know Your Twist

™

Twist

™

Controls

There are two buttons on the base of the Twist

™

:

•   Press the snapshot button to take 

a new picture 

•   Press the Light button to turn on 

the LEDs 

In addition to the camera button, Twist

™

 has a 3.5 mm 

mono jack socket so that external switches can be used 
to take pictures.

Twist

™

Flexible Digital Microscope

Bendy 
gooseneck

Focus wheel

LED lights

LED light on/off

Photo button

Ext photo switch socket

To adjust the focus, rotate the adjustment wheel slowly 
until the image on the screen is clearly displayed.

Marking on label shows reference figure for measurement  
(for user with “Flexi-measure” software only).

Using the Twist

™

/Flexi-Scope

™

software

Control Panel
Current image
Maximize image
Main display

Saved images

Place CD into CD-ROM
drive and follow steps
shown on screen, then
reboot PC before you
start the program

To start the program, go to “Start” 
“Twist

™

”/”Flexi-Scope

™

”

Click this icon to take a picture. 
Pictures taken will be stored in the 
Folder “C \MyPic130” by default

Video settings

Start video recording and choose the 
Video settings. Videos will be stored 
in C \MyVideo130 by default 

Allows the user to take pictures and video 
automatically at set intervals 

Click this icon to launch the “Flexi-Measure” 
application 

Click this icon to Exit the program

Using the Flexi-Measure software

Dimension 
tools

Color & font
Foot notes
Measurement 
settings

Capture the image and
read the magnification
reference number from
the focus wheel. Enter
this figure into the
magnification box

Before measurement,
you need to know the
Magnification reference
number of the captured
images and enter it into
the magnification box”