Lathem LTTC - Manual - manualsarea.com

Page 2 - - LT Series Operations Manual; TABLE OF CONTENTS

1 - LT Series Operations Manual TABLE OF CONTENTS Specifications....................................................................... 2 Introduction.......................................................................... 3 LT Series Models............................................................

Page 3 - - LT Series Operations Manual; SPECIFICATIONS

2 - LT Series Operations Manual SPECIFICATIONS PHYSICAL Height: 7 inches Width: 5 1/4 inches Depth: 11 inches Weight: 12 3/4 pounds (standard models) 14 pounds (numbering models) Case: Impact Resistant Reinforced Lexan Color: Cool Gray Power Cord Length: 6 Feet COMPONENTS Print Wheels: Engraved Bras...

Page 4 - - LT Series Operations Manual; INTRODUCTION

3 - LT Series Operations Manual INTRODUCTION The Lathem LT Series time stamps are considered "standard" by thousands of businesses and institutions because of their low initial cost and years of proven, trouble-free operation. The LT Series offers a wide variety of registration combinations ...

Page 5 - - LT Series Operations Manual; LT SERIES MODELS; LTD; OPTIONAL FEATURES; REPEAT/ADVANCE SWITCH

4 - LT Series Operations Manual LT SERIES MODELS LTD Registers date, month, and year. Type wheels must be advanced manually. Year wheels carry ten (10) years. LTN Registers consecutive numbers. Basic unit includes six (6) numbering wheels which advance automatically. Up to five additional numerical,...

Page 6 - - LT Series Operations Manual; FIXED PAPER GUIDE; GETTING STARTED; Figure 1

5 - LT Series Operations Manual 24-HOUR FORMAT The digital display models (LTTC and LTTNC) can display 12-hour (standard), or 24-hour, also known as the Continental (0-23 hour), format, when specified at time of order. The time wheels can print 24-hour format for an added charge. FIXED PAPER GUIDE P...

Page 7 - - LT Series Operations Manual; SETTING THE TYPE WHEELS; key clockwise, and pulling the cover up and forward.

6 - LT Series Operations Manual SETTING THE TYPE WHEELS As noted in the earlier sections LT SERIES MODELS and OPTIONAL FEATURES, the LT Series Models are available with a variety of date, time, and number wheels. You may set the applicable type wheels according to the following directions. 1. Discon...

Page 8 - - LT Series Operations Manual; SETTING THE DIGITAL DISPLAY; Figure 3

7 - LT Series Operations Manual SETTING THE DIGITAL DISPLAY Models with a "C" affixed to their designation (LTTC and LTTNC) denote units featuring a digital display. This display is factory-set for use in the 12-hour AM/PM format or the 24-hour (Continental) format. The digital display shoul...

Page 9 - - LT Series Operations Manual; ADJUSTING PRINT IMPACT; Figure 4

8 - LT Series Operations Manual ADJUSTING PRINT IMPACT Print impact may be set to any desired level, from very hard to very light. The impact adjuster is located on the bottom of the unit. Using a small flat head screwdriver, turn the adjuster to the right to increase or left to decrease the impact....

Page 10 - - LT Series Operations Manual; CONSECUTIVE/DUPLICATE COUNT; Figure 6a

9 - LT Series Operations Manual CONSECUTIVE/DUPLICATE COUNT (Numbering Units) Units equipped with the numbering feature may be configured for Consecutive Count, advancing the number type wheel after each registration, Duplicate Count, advancing the number type wheel after every two registrations., T...

Page 11 - 0 - LT Series Operations Manual; ADJUSTING THE REGISTRATION POSITION; To adjust the registration position:

10 - LT Series Operations Manual ADJUSTING THE REGISTRATION POSITION Depending on the type of document being stamped, it may be necessary to change the registration position. This can be accomplished by moving the trigger assembly. The trigger assembly has a range of motion of about two (2) inches f...

Page 12 - CHANGING THE RIBBON

11 - LT Series Operations Manual CHANGING THE RIBBON LT Series time stamps use a silk ribbon for long-lasting, high-quality imprints. To avoid damaging the unit, use only a #20-S ribbon. To change the ribbon: 1. Disconnect the power source. 2. Remove the top cover. Remove the frame locking pin and l...

Page 13 - 2 - LT Series Operations Manual; CHANGING THE FUSE; fuse holder cap and turn clockwise until it locks in place.

12 - LT Series Operations Manual CHANGING THE FUSE Each model of the LT Series comes equipped with a fuse. The fuse protects the unit from damage in case of a power surge or electrical overload. If too much power reaches the fuse, the fuse burns out, or is "blown," stopping operation of the ...

Page 14 - CHANGING THE PLATEN

13 - LT Series Operations Manual CHANGING THE PLATEN 1. Disconnect the power source. 2. Remove the top cover. Remove the frame locking pin and lift the top frame. Remove the ribbon (see Changing the Ribbon, Page 11). 3. Lift the printing platen assembly up and out of the frame. (Fig. 10) 4. Insert t...

Page 15 - 4 - LT Series Operations Manual; Limited One-Year Limited Warranty; Lathem Time

14 - LT Series Operations Manual Limited One-Year Limited Warranty Lathem warrants the hardware products described in this guide against defects in material and workmanship for a period of one year from date of original purchase from Lathem or from an authorized Lathem reseller. The conditions of th...

Lathem LTTC - Manual

Table of Contents:

Summary

Other Lathem Models