Lantronix 4092A IRIG-B - Manual

6 2: Installing and Setting Up the 4092A „ Rack mounting screws. „ Screwdriver for the rack mount screws and slide, as needed. Caution Since the unit does not have a AC mains power switch, both the appliance inlet connector and the plug on the detachable power supply cord are considered to be suitab...

8 2: Installing and Setting Up the 4092A To assign the static IP address using Telnet: 1. Telnet to the assigned address, port 9999. 2. Press Enter within five seconds to enter the setup mode. 3. Select Option 0. 4. Set the IP address and follow the on-screen instructions to save the setting. 5. Tel...

4092A Operations and Maintenance Manual 11 3: Monitoring the 4092A 3.1 Accessing the System You access the 4092A system remotely by connecting to its Command-And-Response (CNR) Port through the Ethernet connection. The CNR port (Port 10001), which uses TCP/IP, lets you input commands, displays resul...

14 3: Monitoring the 4092A 3.2.2 Checking Model Number and Software Version Both commands are case sensitive. You do not need to type a carriage return or line feed. To check the TSC model number: „ Type: I • The system returns I4092A-00\r\n , where the 00 is the hardware version. To check the softw...

4092A Operations and Maintenance Manual 15 3.3 Understanding Alarm Output The 4092A automatically publishes alarms to the CNR port as they occur. The alarms appear in the format ALARMfghij where fghij is the summary status of the input and output signals. The format of the alarm status is identical ...

4092A Operations and Maintenance Manual 17 4: Troubleshooting the 4092A Perform all of the following procedures before returning the unit for service. If the unit still appears to have a problem, call Timing Solutions Corporation and request technical support. Have the serial number of your unit rea...

18 4: Troubleshooting the 4092A 4.2 Troubleshooting Output Problems If all of the OUTPUT LEDs are red, the unit is not receiving a valid input signal on the active channel. Look at the INPUT LEDs and resolve the input problem. For more information, see “4.1 Troubleshooting Input Problems” on page 17...

4092A Operations and Maintenance Manual 19 4.4 Configuring for Input Signal and Impedance The Input Signal and Impedance settings are configured at the factory for a modulated input and low Z input and output impedance. If the signal sources have a high Z output impedance, then Caution When opening ...

20 4: Troubleshooting the 4092A Caution When opening the top cover and changing the power supply settings, use proper ESD precautions. This includes ensuring that you are properly grounded before touching the internal PWA of the unit to change the jumper settings. Required for this procedure: „ #1 P...

4092A Operations and Maintenance Manual 21 Required for this procedure: „ #1 Phillips screwdriver To replace a power supply: 1. Disconnect the power cord from the failed power supply. 2. Using a #1 Phillips screwdriver, remove the two screws from the failed power supply. 3. Using #1 Phillips screwdr...

4092A Operations and Maintenance Manual 23 5: Warranty and Shipping Information This chapter provides information on how to contact Timing Solutions Corporation for warranty service, as well as shipping guidelines for the 4092A. 5.1 Warranty Information The 4092A carries a warranty from Timing Solut...

4092A Operations and Maintenance Manual 25 Appendix A: Specifications A.3 Electrical Specifications Table 3 lists the electrical specifications for the 4092A. Table 3: Electrical specifications Item Specification Protection Class Class I (Grounded Type) Power Input Voltage 100–240 V ~ 50/60 Hz 0.5 A...

26 Appendix A: Specifications A.3.1 Environment Specifications Warning This unit is for INDOOR USE ONLY. It is not sealed to prevent moisture from entering the enclosure. Equipment intended to be installed in an enclosed- or open-type equipment rack. „ Pollution Degree II per EN61010-1 „ Installatio...

4092A Operations and Maintenance Manual 27 Glossary \n Line feed \r Carriage return CNR Command and Response DHCP Dynamic Host Configuration Protocol ESD electrostatic discharge LED light-emitting diode LSB least significant bit MSB most significant bit PDF portable document format PWA printed wirin...

4092A Operations and Maintenance Manual 29 Index Numerics 4092A accessing remotely 11alarms 15cleaning 9command interface 11front panel 3installing 5monitoring 11overview 3rear panel 3required cables 5specifications 25unpacking 5 A accessing the 4092A remotely 11active input channel selecting from t...