Page 2 - Contents
NC-6 i Contents 1 Welcome 1.1 Trademark Acknowledgements ................................................... 1-2 1.2 About PageScope Light................................................................ 1-2 2 Getting Ready 2.1 Selecting the Network Print Method..........................................
Page 3 - ii; Using PageScope Light
ii NC-6 7.2 Setting Up the Network Connections ......................................... 7-2 7.2.1 Peer-to-Peer Printing ................................................................. 7-2Windows 95 (OSR 2.5)/ Windows 98/ Windows 98 SE/ Windows ME .....................................................
Page 4 - iii; User Instructions; FCC Part 15-Radio Frequency Devices; For Canada
NC-6 iii User Instructions For the U.S.A. FCC Part 15-Radio Frequency Devices For Canada Interference-Causing Equipment Standard (ICES-003 Issue 3) For Europe CE Marking (Declaration of Conformity) NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, ...
Page 5 - iv; For countries subject to Class B regulations
iv NC-6 For countries subject to Class B regulations For countries not subject to Class B regulations This device must be used with shielded interface cables. The use of non-shielded cables is likely to result in interference with radio communications and is prohibited under CISPR 22 rules and local...
Page 6 - Welcome; Read these instructions thoroughly before using the functions.; Note; The contents of this manual are subject to change without notice.
Welcome 1 NC-6 1-1 1 Welcome This manual provides information on setting up and using a copier as a network printer. Read these instructions thoroughly before using the functions. For instructions on using the copier itself and for general safety precautions, refer to the manual provided with the co...
Page 7 - Trademark Acknowledgements; Ethernet is a registered trademark of Xerox Corporation.; About PageScope Light
1 Welcome 1-2 NC-6 1.1 Trademark Acknowledgements PageScope is trademark of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Ethernet is a registered trademark of Xerox Corporation. PCL is a registered trademark of Hewlett-Packard Company. Microsoft, Windows, and Windows NT are registered trademarks of Mi...
Page 8 - Getting Ready; “Selecting the Network Print Method” on page 2-2
Getting Ready 2 NC-6 2-1 2 Getting Ready This manual provides detailed information on using a copier as a network printer. However, not all information provided will be required by all users. This chapter is designed to make it easier to find the information and procedures required for your setup. 1...
Page 9 - Selecting the Network Print Method; Network Setup Printing
2 Getting Ready 2-2 NC-6 2.1 Selecting the Network Print Method Once a network card has been installed, various methods for network printing become available. This section describes how to select the appropriate network print method for the type of operating system that you are using. For Windows 95...
Page 12 - For Windows XP; IPP Printing
Getting Ready 2 NC-6 2-5 For Windows XP IPP Printing G You can connect a copier and computer via the IPP Print Service. G The IPP Print Service is available with a standard installation of the operating system. G HTTP (Hyper Text Transfer Protocol), which is part of the TCP/IP protocol is used. Busi...
Page 13 - Supported Environments
2 Getting Ready 2-6 NC-6 For NetWare (NetWare Server/ Windows Client) When using NetWare, you can use a computer running Windows as a NetWare client to print to a copier via a NetWare server. Supported Environments The controller supports the system environments described below. NetWare version Prot...
Page 14 - Checking the Setup Procedures; Connect the network cable. (“4 Connecting the Network Cable”)
Getting Ready 2 NC-6 2-7 2.2 Checking the Setup Procedures This section describes the required procedures for setting up network printing for the selected network print method. Peer-to-Peer Printing 1 Check that all of the accessories have been included in the package. (“3 Checking the Accessories”)...
Page 15 - Install the printer driver.
2 Getting Ready 2-8 NC-6 LPR / PORT 9100 Printing 1 Check that all of the accessories have been included in the package. (“3 Checking the Accessories”) 2 Connect the network cable. (“4 Connecting the Network Cable”) 3 Specify the IP address, subnet mask, and default gateway settings for the copier. ...
Page 18 - Checking the Accessories; Accessories; PageScope CD (Includes the network utility software)
Checking the Accessories 3 NC-6 3-1 3 Checking the Accessories Check that all of the accessories listed below are included in the package. If any item is missing, contact your service representative. 3.1 Accessories G PageScope CD (Includes the network utility software) G This manual: User Manual fo...
Page 20 - Connecting the Network Cable; Types of Cable That Can Be Used
Connecting the Network Cable 4 NC-6 4-1 4 Connecting the Network Cable Connect the network cable to the copier. 4.1 Types of Cable That Can Be Used Use a Category 5 or 5E network cable. 4.2 Connecting the Network Cable Insert the connectors on the network cable into the network ports. 1 Insert the c...
Page 22 - Assigning an IP Address; Entering the IP Address From the Control Panel; If an element of the number is less than three digits, press the
Assigning an IP Address 5 NC-6 5-1 5 Assigning an IP Address From the control panel of the copier, assign an IP address to the copier. ✎ Note Always assign an IP address only after consulting your network administrator. 5.1 Entering the IP Address From the Control Panel Use the 10-key pad on the con...
Page 24 - Proceed to enter the subnet mask setting.
Assigning an IP Address 5 NC-6 5-3 Check with your network administrator to determine if there is a DHCP server available on the network. (If there is, a special IP address will be assigned by the AutoIP function. However, the copier will not be able to communicate with other devices on the network ...
Page 26 - Printing the Configuration Page
Printing the Configuration Page 6 NC-6 6-1 6 Printing the Configuration Page Detailed information on the settings can be printed so that the contents of the settings can be easily checked. ✎ Note The Configuration Page cannot be printed for copiers that are not equipped with the optional PCL printer...
Page 28 - Connecting the Computer and Copier; Procedures Described in This Chapter
Connecting the Computer and Copier 7 NC-6 7-1 7 Connecting the Computer and Copier This chapter describes how to connect the computer and copier, and the settings required to enable the copier to print jobs received over the network. 7.1 Procedures Described in This Chapter The connection procedures...
Page 29 - Setting Up the Network Connections; Important; Check that the computer is set up to use the TCP/IP protocol.; Other
7 Connecting the Computer and Copier 7-2 NC-6 7.2 Setting Up the Network Connections 7.2.1 Peer-to-Peer Printing Windows 95 (OSR 2.5)/ Windows 98/ Windows 98 SE/ Windows ME ✎ Important Before continuing to set up the network settings, check the following: Check that the computer is set up to use the...
Page 30 - LPR Printing; Printer Name or IP; Use half-pitch characters to enter the queue name.
Connecting the Computer and Copier 7 NC-6 7-3 7.2.2 LPR Printing Windows 2000 ✎ Important Before continuing to set up the network settings, check the following: Check that the computer is set up to use the TCP/IP protocol. Check that the copier is also set up to use the TCP/IP protocol. Check that t...
Page 32 - Installing the Microsoft TCP/IP Printing Service; Right-click the icon for the installed printer driver.; LPR Port
Connecting the Computer and Copier 7 NC-6 7-5 Windows NT 4.0 ✎ Important Before continuing to set up the network settings, check the following: Check that the computer is set up to use the TCP/IP protocol. Check that the copier is also set up to use the TCP/IP protocol. Check that the printer driver...
Page 33 - Name or address of server providing lpd; Enter the name of the print queue in the; Name of printer or print
7 Connecting the Computer and Copier 7-6 NC-6 6 After the Add LPR Compatible Printer dialog box appears, enter the copier IP address in the Name or address of server providing lpd services box, and then click [OK]. Enter the name of the print queue in the Name of printer or print queue on that serve...
Page 34 - Check the IPP Settings Using PageScope Light
Connecting the Computer and Copier 7 NC-6 7-7 7 Enter the IP address for the copier into the Printer Name or IP Address box, and then click [Next>]. 8 Select Custom , and then click [Settings]. 9 Select RAW as the protocol. 10 Enter “9100” for the Port Number setting, and then click [OK]. 11 Clic...
Page 35 - Setting Up the IPP Print Connection; Network Printer; Select; Connect to a printer on the Internet or on your intranet
7 Connecting the Computer and Copier 7-8 NC-6 Setting Up the IPP Print Connection Set up the IPP Print connection. In order to set up IPP printing, you must start by installing the printer driver. (For instructions on installing the GDI driver, refer to “GDI Printer Controller” in the manual provide...
Page 36 - Connecting a Copier to the NetWare Server
Connecting the Computer and Copier 7 NC-6 7-9 7.2.5 Connecting a Copier to the NetWare Server Supported Environments The controller supports the system environments described below. Setting Up NetWare 4.x/ 5.x/ 6 Print Server Mode 1 Log in with administrator privileges. 2 Start up NWadmin. 3 Select ...
Page 38 - NetWare Configuration; from the “Network” tab, and then use
Connecting the Computer and Copier 7 NC-6 7-11 5 Start up PageScope Light and log in to the Administrator mode, select NetWare Configuration from the “Network” tab, and then use PageScope Light to specify the following settings on the copier. ❍ Refer to “8 Using PageScope Light” for details. 6 Load ...
Page 40 - Setting Up the Windows Computer for the NetWare Client; On the printer model list, select the printer driver on the CD-ROM.
Connecting the Computer and Copier 7 NC-6 7-13 Setting Up the Windows Computer for the NetWare Client 1 Click [Start] - [Settings] - [Printer], and then double-click the “Add Printer” icon. 2 For the printer port, browse the network and specify the name of the queue (or the name of the NDPS printer)...
Page 42 - What is PageScope Light?
Using PageScope Light 8 NC-6 8-1 8 Using PageScope Light 8.1 What is PageScope Light? PageScope Light is a device control utility program provided by the HTTP server built into the network interface card. This utility can be used with a Web browser as an interface for remotely controlling the copier...
Page 45 - About the Screen Layout; The following screen appears when you access PageScope Light.
8 Using PageScope Light 8-4 NC-6 8.5 About the Screen Layout The following screen appears when you access PageScope Light. ✎ Note Screen images used in this manual may differ from the actual screen display. They are also subject to change without notice. 1 Logo Click on this to jump to the manufactu...
Page 46 - Logging In as an Administrator; Logging In to Administrator Mode; Click the [Login] button to log in to the Administrator mode.; About the File Download Function; Types of File That Can Be Downloaded; PCL files
Using PageScope Light 8 NC-6 8-5 8.6 Logging In as an Administrator Some of the settings available in PageScope Light can only be changed by an administrator. These settings are only displayed when you log in to the Administrator mode. Logging In to Administrator Mode 1 Enter the administrator passw...
Page 48 - Appendix; Product Specifications; This device supports the BootP protocol, which is part of the TCP/IP
Appendix 9 NC-6 9-1 9 Appendix 9.1 Product Specifications *1 This device supports the BootP protocol, which is part of the TCP/IP protocol. If the BootP server has been enabled with the Network Setup utility, the IP address for the copier will be automatically assigned. For details, refer to the Use...
Page 49 - Troubleshooting
9 Appendix 9-2 NC-6 9.2 Troubleshooting Check the following chart if you have problems using the copier as a network printer. Checkpoint Possible cause Solution 1 Has the print job reached the copier? Yes A copier error has occurred. (No paper, no toner, etc.) Check the copier and resolve any errors...
