Kodak CIS-201 - Manual
Kodak CIS-201 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Densitometer Method; mus; Note; Example
- Page 3 – Setting the Paper Slope; Ringaround Method
- Page 5 – Normal Correction; not; DO NOT
- Page 6 – Testing the New Paper; Example 1
- Page 11 – To confirm that the current setup is correct:; To make new reference prints:; Before Converting to the New Paper; To confirm that the current setup is correct:
- Page 12 – Consumer Imaging; EASTMAN KODAK COMPANY; MORE INFORMATION; —Available 24 hours a day, 7 days a week—
©Eastman Kodak Company, 2000
March 2000
•
CIS-201
CURRENT INFORMATION SUMMARY
Printer Conversion to
KODAK EKTACOLOR Edge 8 and
EKTACOLOR ROYAL VIII Papers
KODAK EKTACOLOR Edge 8 and ROYAL VIII Papers
incorporate new image-forming components to deliver
improved colors. These new papers are designed so that a
visually neutral patch will result in approximately balanced
red, green, and blue densities when measured with
densitometers that conform to ANSI Status A responses.
Some densitometers that do not conform to ANSI Status A
responses may produce non-matched red, green, and blue
densities for a neutral patch on these new papers. Labs that
use these non-Status A densitometers must compensate for
the differences in densitometer performance when they set
up printers for the new papers.
WHY DOES THIS HAPPEN?
Densitometers fall into two classes: (1) for analytical use and
(2) for comparative use.
Analytical densitometers
conform to an ANSI standard
called “Status A.” Status A densitometers correlate colors
similarly to the human eye through a wide color and density
range. These densitometers will give similar readings for
KODAK EKTACOLOR Edge 7/ROYAL VII and
EKTACOLOR Edge 8/ROYAL VIII Papers if the prints
appear visually matched.
Comparative densitometers
are designed to match prints
to a specific density. They are
not
intended for use over a
wide range of densities and colors, and they do not see colors
as the human eye does. These densitometers are often used
in printing systems as a part of a minilab or a high-speed
printer. They produce consistent measurements in the ranges
used for printer setup. However, with KODAK
EKTACOLOR Edge 8 or ROYAL VIII Paper, they do not
measure the neutral aim patches as neutral. For example, an
aim print on EKTACOLOR Edge 8/ROYAL VIII Paper
measures 0.80 red, 0.80 green, and 0.80 blue with a Status A
densitometer. The same print may measure 0.70 red,
0.80þgreen, and 0.80 blue with a comparative densitometer.
WHAT DOES THIS MEAN FOR LABS?
New EKTACOLOR Edge 8 and ROYAL VIII Papers
provide many performance advantages. But when they are
used with densitometers that do not conform to Status A
specifications, results may vary. Labs that use these
non-Status A densitometers must compensate for differences
in densitometer performance when setting up their printers
for the new papers.
When you are ready to convert to KODAK
EKTACOLOR Edge 8 or ROYAL VIII Paper, follow the
procedure below to determine how your densitometer
performs. Once you’ve determined the densitometer
performance, choose the appropriate compensation
procedure (if one is necessary).
To Determine If Compensation Is Required
1. Print your “Normal” Printer Control Negative on
EKTACOLOR Edge 7 or ROYAL VII Paper at the aim
density.
2. With EKTACOLOR Edge 8 or ROYAL VIII Paper,
balance to match the density readings from Step 1.
3. Compare the two prints. If the prints match visually,
follow normal printer paper conversion procedures (see
your printer manual). If the print from Step 2 appears
cyan, the densitometer is reading EKTACOLOR Edge 8
or ROYAL VIII Paper differently. You will need to
follow one of the compensation procedures below.
Note: Compensation procedures have not been prepared
for equipment that produces matched prints in Step 3 of
the procedure above. If your printer is not included in
the list below, follow your equipment manufacturer’s
paper setup instructions.
COMPENSATION PROCEDURES
If you have one of the printers in the following list, choose
the appropriate procedure:
Compensation Procedure for NORITSU 1401/1501
Printers
Compensation Procedure for NORITSU 1801 Micro
Printer
Compensation Procedure for NORITSU 1701/1702
Printers (without NOUS Scanner)
Compensation Procedure for NORITSU 901, 1001,
1201, and 1202 Printers
Compensation Procedure for COPAL Minilab, Models
1B, 1C, 5C, 5C II, 5L, 5S
Compensation Procedure for AGFA MSP Printers
Compensation Procedure for AGFA MSC Printers
Compensation Procedure for GRETAG Masterlab
Compensation Procedure for GRETAG Masterflex
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Printer Conversion to KODAK EKTACOLOR Edge 8 and EKTACOLOR ROYAL VIII Papers • CIS-201 For other printers, follow these steps: 1. Print your “Normal” Printer Control Negative on EKTACOLOR Edge 8/ROYAL VIII Paper again at the aim density, and with 1 red, 2 red, 3 red, and 4 red color-correction but...
Printer Conversion to KODAK EKTACOLOR Edge 8 and EKTACOLOR ROYAL VIII Papers • CIS-201 3 Morning Setup channel will use the new paper, you would input the following: This Channel Balance correction will be made to channels 00, 01, 02, 03, 04, 05, 06, and 07. Note: If the channels that will use the n...
Printer Conversion to KODAK EKTACOLOR Edge 8 and EKTACOLOR ROYAL VIII Papers • CIS-201 5 Divide the Cyan, Magenta, and Yellow difference values by 10 to obtain the color correction: The correction for this example is -1.5 Cyan, -0.7 Magenta, 0.0 Yellow, and -0.4 Density. 4. When the message SET REFE...
