Kodak A-61514 - Manual

A-61514 September 2004 3 Preparing documents for scanning • A batch of documents to be fed into the scanner must be arranged so that the leading edges of all documents are aligned and centered under the automatic document feeder. This allows the feeder to introduce documents into the scanner one at ...

4 A-61514 September 2004 Safety information • When placing the scanner, make sure that the electrical power outlet is located within 1.52 metres (5 feet) of the scanner and is easily accessible. CAUTION: The scanner and power supply must only be used indoors in a dry location. • Material Safety Data...

A-61514 September 2004 5 Safety and regulatory agency approvals The Kodak i100 Series Scanners conform to applicable national and international product safety and electronic emission regulatory requirements. This includes, but is not limited to, the following: Environmental information • The Kodak i...

6 A-61514 September 2004 EMC statements United States This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential install...

A-61514 September 2004 7 Installing the Scanner Site specifications Place the scanner: • in a clean area with temperature and relative humidity typical of an office environment CAUTION: The scanner and power supply must only be used indoors in a dry location. • on a stable, level work surface capabl...

8 A-61514 September 2004 Recommended system configuration To operate the scanner at its optimum speed, the following configuration (or better) is recommended. NOTE: The actual performance of the system depends on the scanning application, choice of scanning parameters, and the host computer configur...

A-61514 September 2004 9 Removing the foam sheet The scanner is packed with a foam sheet inside to protect the rollers during shipping. This foam sheet must be removed before you can begin scanning. 1. Lift the scanner out of the box and place it on a stable, level work surface that is capable of su...

A-61514 September 2004 11 Internal 1 Separator module2 Normal force rollers3 Rear drive roller cover4 Front drive roller cover5 Feed module 1 2 3 4 5

12 A-61514 September 2004 Making connections Follow the instructions for installing the IEEE-1394 (FireWire) card and the Kodak Driver Software before you plug the scanner into the host computer. IMPORTANT: You must install the software on the host computer before you install the scanner. Installing...

A-61514 September 2004 13 Power setup One or more power cords may be supplied with the scanner. Use only the cord required for your power type. Dispose of any unneeded power cords properly. Use only the power supply that was provided with the scanner. CAUTION: The scanner and power supply must only ...

14 A-61514 September 2004 If you are installing the scanner on a computer that is running Windows 2000, the following screen may appear. • Select Yes . Kodak has successfully tested the i100 Series Scanners with Windows 2000. Your scanner is now installed. If you are installing the scanner on a comp...

A-61514 September 2004 15 1. Select Next . The following screen appears. 2. Select Continue Anyway . Kodak has successfully tested the i100 Series Scanners with Windows XP. The following screen appears. 3. Select Finish . Your scanner is now installed.

16 A-61514 September 2004 Input and output trays The input and output trays snap into place. They also may be adjusted to fit different document sizes. The input and output trays also may be folded flat up against the scanner to save space when the scanner is not in use. Attaching the input tray 1. ...

A-61514 September 2004 17 Adjusting the output tray The adjustable output tray has three possible positions. • Set the output tray to the lowest position when you are scanning long documents. • Set the output tray to the middle position when you are scanning letter- or A4-size documents. • Set the o...

18 A-61514 September 2004 Using the Scanner Starting and stopping scanning Scanning is controlled by software developed for your application. To start and stop scanning, refer to the documentation provided with your software. Automatic feeding To scan a batch of documents, follow the guidelines for ...

A-61514 September 2004 19 Continuous feeding Continuous feeding allows you to place additional batches of documents in the feeder for “infinite” feeding (with operator assistance). • When only a few documents from one batch remain in the feeder, place the next batch face down on top of those documen...

20 A-61514 September 2004 Damaged documents You can scan torn or fragile documents through the automatic document feeder if they are placed in a protective plastic sleeve. 1. Place the damaged document into a protective sleeve. 2. Position the sleeve face down , folded edge first, and centered in th...

A-61514 September 2004 21 Maintenance Cleaning the scanner The scanner will collect dust and other debris during routine scanning. For optimal scanner performance, follow the detailed cleaning instructions in this section and clean the feed module rollers, separator module rollers, imaging guides, t...

A-61514 September 2004 23 7. Inspect the rollers. If the separator roller tires show signs of wear or damage, replace the tires or the separator module. 8. Insert the separator module and align the shaft ends. 9. Press until the separator module clicks into place. 10. Go to the next section to clean...

26 A-61514 September 2004 Cleaning the paper path 1. Remove the wrapping from the Transport Cleaning Sheet. 2. Adjust the paper feeder guides to fit the cleaning sheet. 3. Feed the cleaning sheet (adhesive side up) through the scanner in portrait orientation until all residue is removed from the dri...

A-61514 September 2004 27 Calibrating the scanner Calibration optimizes the optical system in your scanner in order to achieve the best overall quality of scanned images. Frequent calibration is not needed or recommended. Calibration instructions can be found in the Image Processing Guide for Kodak ...

28 A-61514 September 2004 Troubleshooting Indicator lights There are two indicator lights — one red, one green — on the scanner that provides information about what the scanner is doing. Green on — scanner is ready to scan Green flashing — scanner is busy Red on — an error condition exists (refer to...

A-61514 September 2004 29 Lamps The scanner has a lamp saver feature to prolong lamp life. The lamps shut off after five minutes of scanner idle time. Clearing document jams 1. Remove any documents from the feeder area. 2. Lift up the scanner door release to unlatch the scanner door. 3. Pull up to o...

30 A-61514 September 2004 System is not responding If the scanner and/or host computer are not responding, perform the following steps. 1. Power down the computer. 2. Power down the scanner. 3. Disconnect the IEEE-1394 (FireWire) cable from the IEEE-1394 port on the back of the scanner. 4. Power up ...

A-61514 September 2004 31 Problem solving Occasionally, you may experience a problem with your scanner. In many cases, you can easily fix the problem yourself. To perform suggested maintenance, refer to the Maintenance section. You may also need to check your scanning application. Problem Possible S...

A-61514 September 2004 A-1 Appendix A Specifications Scanner Type i150 Scanner: simplex color scanner with automatic document feeder i160 Scanner: duplex color scanner with automatic document feeder Image Capture Resolution 75 dpi to 300 dpi color and bi-tonal ADF Scanning Speed i150 Scanner/i160 Sc...

A-61514 September 2004 B-1 Appendix B Supplies and Accessories Contact your scanner supplier to order supplies. Item CAT No. Kodak Feeder Consumables Kit for i100 Series Scanners (1 complete feed module, 1 complete separator module, 2 pre-separation pads, 24 roller tires) 124 1066 Kodak Extra-Large ...

A-61514 9/2004©Eastman Kodak Company, 2004 CAT No. 126 4951 EASTMAN KODAK COMPANYDocument ImagingRochester, New York 14650 Kodak and Ektamate are trademarks ofEastman Kodak Company. Printed on recycled paper. DOCUMENTI M A G I N G i100 Series Scanners User’s Guide A-61514 Part No. 9E3718 CAT No. 126...