Knoll HT211 - Manual - manualsarea.com

Page 2 - IMPORTANT SAFEGUARDS; Installation; a minimum of one minute; Fire and Shock Precautions

IMPORTANT SAFEGUARDS These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings. Installation • For best results, use your projector in a darkened room. • Place the projector on a flat, level surface in a dr...

Page 3 - Table of Contents

Table of Contents 2 IMPORTANT SAFETY INFORMATION 3 Table of contents 4 Basic information 4 Features 5 Remote control 6 Terminal connections 6 Projector part identification 7 Projector positioning 8 Connecting video equipment 9 Connecting component video 10 Connecting a PC or Macintosh 12 Using the r...

Page 4 - The features you'll enjoy...; SECAM (France and Eastern Europe standard); sources

Basic Information Congratulations On Your Purchase of the Knöll Projector! The Knöll DLP is one of the very best projectors available today. It enables you to project precise images up to 200 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, document ...

Page 5 - Remote Control; ) Press firmly and; Notes; If the remote; Remote control effective range

Remote Control Inserting the batteries 1) Press firmly and slide the battery cover off. 2) Insert the supplied two batteries (size AAA). Ensure that the polarities (+ and -) of the batteries are aligned correctly. Always replace batteries with fresh alkaline type. 3) Slip the cover back over the bat...

Page 6 - Ensure; all

Terminal Connection Panel Projector Part Identification Installation The distance from the projector lens to the screen determines to the size of the projected image, therefore, you need to consider the place where you set up the projector and screen before making connections. You also need to consi...

Page 7 - Projector Positioning; Width; Image Drop

Projector Positioning The projected image becomes larger as the distance between the unit and screen increases. The minimum image size is about 36 inches (93cm) diagonally at a distance of about 1.2m (3.9 feet) and the maximum size is about 200 inches (508cm) at a distance of 6.8m (22.3 feet) from t...

Page 8 - Connecting Video Equipment; You can switch the input source; Before connecting; Turn off the components that are to

Connecting Video Equipment You can connect a document camera, VCR, laser disc player, and DVD player, etc. Connecting to the VIDEO IN VIDEO/S-VIDEO JACKS You can connect up to two pieces of video equipment to the VIDEO IN jacks following the illustration below. Two types of connections can be made. ...

Page 10 - Connecting a PC or Macintosh; Turn off the components that are to be connected.; PowerBook Connection; Depending on the model of your PowerBook, the additional Apple

Connecting a PC or Macintosh Connecting a PC or Macintosh to the Projector enables computer images for impressive presentations. • The following display standards are supported by the HT211 (HT201 may not support some of the higher resolutions): VGA 640x480 for graphics VGA 640x400 for graphics XGA ...

Page 11 - Modifying the DIP switch (for Macintosh) setting; Modify the DIP switch setting on the MAC cable as shown below.; Some examples of DIP switch settings; same way as the computer mouse click button.

Modifying the DIP switch (for Macintosh) setting Modify the DIP switch setting on the MAC cable as shown below. Macintosh adapter cable DIP switch setting (o=ON) MONITOR RESOLUTION 1 2 3 4 5 6 Multiple scan 21 o o o Multiple scan 21 o o o Multiple scan 21 o o o o VGA/SVGA o o 21 Color 1152x870 o o o...

Page 12 - Connecting the remote mouse receiver to an IBM PC/AT computer; D-Sub Pin Assignments; Green Gnd 12 No Connection

Connecting the remote mouse receiver to an IBM PC/AT computer Connect the IBM/Mac connector on the remote mouse receiver and PC's mouse port with the supplied serial cable. Connecting the remote mouse receiver to an IBM PS/2 or Macintosh computer Connect the supplied serial cable to the IBM/Mac conn...

Page 13 - Operation; Using the Projector; indicator on top of the unit lights in amber.

Operation Using the Projector 1) Connect the supplied power cable to the projector, then to the wall outlet (the mains). The POWER indicator on top of the unit lights in amber. 2) Press the POWER ON button on the remote control or the POWER button on top of the unit to turn on the unit. The POWER in...

Page 15 - Adjusting the volume of the projector speaker

Windows 95 There are two methods you can use to change your resolution. Method 1 1. Move your cursor to the background image and click. 2. In the "Properties" menu, select "Settings." 3. Change your resolution and click "OK." 4. You may be asked to reboot for the changes to t...

Page 16 - Enlarging the picture; To move to the desired portion of the enlarged picture; The button lights in red. If you don't proceed to step; Selecting the input source with the remote; Press Video or RGB. For S-Video press the video button twice.; Selecting menu options; Open the flip cover and press the menu button.; Projection Type

Enlarging the picture You can enlarge a portion of the picture up to four times its normal size. The overall picture size will remain the same and the enlarged picture will completely fill the overall picture frame. Press ZOOM +. While the button is pressed the picture is enlarged until it becomes a...

Page 17 - Aspect Ratio Type Means

Setting "INPUT MODE" to "YCbCr" or Component Video When you have connected the component video (YCbCr) signal output jacks of the video component to the RGB IN connector on the unit, set the projector to "YCbCr" to obtain better picture quality. 1. Turn the component video im...

Page 20 - Specifications; Electrical

Specifications Optical DMD TM Single Chip Digital Micro Device (DMD), 1024x768 pixels Single Chip Digital Micro Device (DMD), 800x600 pixels Lens Manual focus F3.0 f =23mm Lamp Model 28-631 high performance compact lamp Image Size 914 to 5080mm (36 to 200 inches) diagonal Projection Distance 1.2 to ...

Page 22 - Condition Status; Replacing the lamp housing

When the STATUS indicator on the projector keypad lights or blinks Status Light Message Condition Status OFF Normal On Continually The projector lamp has exceeded 1000 hours of operation and should be replaced. Blinking Very Rapidly (On and off in a cycle of 1 sec.) The lamp housing is not correctly...

Page 23 - Lamp Replacement Procedure; : Do not use a lamp housing other

Lamp Replacement Procedure 1. Switch off the main power and unplug the power cord. 2. Wait at least one hour for the lamp to cool. 3. Turn the unit upside down carefully. 4. Loosen the lamp cover securing screw. 5. Slide the lamp cover in the direction of the arrow and remove it. CAUTION : Do not us...

Knoll HT211 - Manual

Table of Contents:

Summary

Other Knoll Models