KitchenAid KMHC319EBS - Installation Manual
KitchenAid KMHC319EBS – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION REQUIREMENTS; Tools and Parts; Tools Needed; Remove Cardboard Template; Set the cardboard template to the side and refer to it during; Location Requirements; Special Requirements; For Wall Venting Installation Only:
- Page 3 – Installation Dimensions; Product Dimensions; Electrical Requirements; Electrical Shock Hazard; WARNING; GROUNDING INSTRUCTIONS
- Page 4 – INSTALLATION INSTRUCTIONS; Remove Mounting Plate; Rotate Blower Motor; Wall Venting Installation Only
- Page 5 – Roof Venting Installation Only
- Page 6 – Mark the center of each stud, and draw a plumb line down; Possible Wall Stud Configurations; Figure 1; No Wall Studs at End Holes; Figure 2; Wall Stud at One End Hole; Figure 3; Wall Studs at Both End Holes; Figure 4
- Page 7 – Mark Rear Wall; Drill Holes in Rear Wall; Installation for Wall Stud at One End Hole (Figure 3)
- Page 8 – Attach Mounting Plate to Wall; No Wall Studs at End Holes (Figures 1 and 2); Start toggle nuts on bolts from the back of the mounting plate.; Prepare Upper Cabinet
- Page 9 – For Roof Venting Installation Only; Install Damper Assembly; Secure damper assembly with 2 sheet metal screws.; Install the Microwave Oven; Make sure the microwave oven door is closed and taped shut.; With front of microwave oven still tilted, thread power supply; Excessive Weight Hazard
- Page 10 – Loosen mounting plate screws. Adjust mounting plate and; Insert damper assembly through the cabinet cutout so that the; Complete Installation; If the microwave oven does not operate:
- Page 11 – VENTING DESIGN SPECIFICATIONS; For optimal venting installation, we recommend:
- Page 12 – Recommended Vent Length; ASSISTANCE; Replacement Parts; Accessories
- Page 13 – Outillage et pièces; Outillage nécessaire; Votre sécurité et celle des autres est très importante.; AVERTISSEMENT
- Page 14 – Dépose du gabarit de carton; Mettre le gabarit de carton de côté et s'y référer lors de l'étape; Exigences d'emplacement; Exigences spéciales; Dimensions du produit
- Page 15 – Spécifications électriques; INSTRUCTIONS D'INSTALLATION; Dépose de la plaque de montage; Si la plaque de montage est fixée sur la partie arrière du four à; Réorientation du moteur du ventilateur; Pour une installation avec décharge murale seulement; Ôter les vis fixant la plaque de support du clapet anti-reflux à; Risque de choc électrique; INSTRUCTIONS DE LIAISON; L’utilisation incorrecte du
- Page 18 – Tracé sur le mur arrière
- Page 19 – Perçage de trous dans le mur arrière; Poteau du colombage mural à un trou d’angle (Figure 3); Si l'on souhaite fixer l'appareil sur un second poteau du; Fixation de la plaque de montage sur; Engager un écrou articulé sur chaque vis par l'arrière de la
- Page 20 – Alors que les pattes de support de la plaque de montage sont; Préparation du placard supérieur; À l’aide d’une scie à guichet, découper la zone rectangulaire.
- Page 21 – (pour décharge à travers le mur uniquement); Vérifier que la lame du clapet anti-reflux manœuvre librement; Installation du four à micro-ondes; Vérifier que la porte du four à micro-ondes est fermée, et; Faire intervenir 2 personnes ou plus pour soulever le four à; Desserrer les vis de la plaque de montage. Ajuster la plaque; Risque du poids excessif
- Page 22 – Achever l'installation; Brancher le four à micro-ondes sur une prise à trois alvéoles
- Page 23 – SPÉCIFICATIONS/CONCEPTION DU CIRCUIT D'ÉVACUATION; Raccord de transition rectangulaire/rond
- Page 24 – Longueur recommandée du circuit d'évacuation; Pièces de rechange; Accessoires
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
DE L’ENSEMBLE FOUR À MICRO-ONDES/HOTTE
MICROWAVE HOOD COMBINATION SAFETY
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Ce produit est conçu pour l’utilisation au-dessus d’appareils de cuisson électriques ou à gaz de 36" (91,4 cm) de largeur ou moins. Voir
la section “Exigences d’installation” pour d’autres remarques.
Ces instructions d’installation sont valables pour plusieurs modèles. Il se peut que l’apparence de votre propre modèle soit légèrement
différente de celle montrée sur les illustrations dans ce document.
Table of Contents / Table des matières
MICROWAVE HOOD COMBINATION SAFETY...................... 1
INSTALLATION REQUIREMENTS........................................... 2
Tools and Parts ...................................................................... 2
Remove Cardboard Template ............................................... 2
Location Requirements .......................................................... 2
Product Dimensions .............................................................. 3
Electrical Requirements ........................................................ 3
INSTALLATION INSTRUCTIONS............................................. 4
Remove Mounting Plate......................................................... 4
Rotate Blower Motor .............................................................. 4
Locate Wall Stud(s) ................................................................ 6
Mark Rear Wall ....................................................................... 7
Drill Holes in Rear Wall ........................................................... 7
Attach Mounting Plate to Wall ............................................... 8
Prepare Upper Cabinet .......................................................... 8
Install Damper Assembly ....................................................... 9
Install the Microwave Oven .................................................... 9
Complete Installation ........................................................... 10
VENTING DESIGN SPECIFICATIONS ................................... 11
ASSISTANCE........................................................................... 12
Replacement Parts............................................................... 12
Accessories .......................................................................... 12
SÉCURITÉ DE L’ENSEMBLE FOUR À MICRO-ONDES/HOTTE ..........13
EXIGENCES D'INSTALLATION........................................................... 13
Outillage et pièces ............................................................................. 13
Dépose du gabarit de carton ............................................................ 14
Exigences d'emplacement ................................................................ 14
Dimensions du produit ..................................................................... 14
Spécifications électriques ................................................................. 15
INSTRUCTIONS D'INSTALLATION .................................................... 15
Dépose de la plaque de montage ..................................................... 15
Réorientation du moteur du ventilateur ............................................ 15
Identifier la position du/des poteau(x) du colombage mural ............ 17
Tracé sur le mur arrière ..................................................................... 18
Perçage de trous dans le mur arrière................................................ 19
Fixation de la plaque de montage sur le mur ................................... 19
Préparation du placard supérieur ..................................................... 20
Installation du module du clapet anti-reflux...................................... 21
Installation du four à micro-ondes .................................................... 21
Achever l'installation.......................................................................... 22
SPÉCIFICATIONS/CONCEPTION DU CIRCUIT D'ÉVACUATION........23
ASSISTANCE ........................................................................................ 24
Pièces de rechange ........................................................................... 24
Accessoires ....................................................................................... 24
W10724871A
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for KitchenAid KMHC319EBS
Summary
2 INSTALLATION REQUIREMENTS Tools and Parts Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Parts Supplied For information on reordering, see “Replacement Parts” section.NOTE: The hardware items list...
3 Installation Dimensions NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section. *30" (76.2 cm) is typical for 66" (167.6 cm) installation height. Exact dimensions may vary depending on type of range/cooktop below. Product Dimensions *Overa...
4 INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be in the foam packaging, or it may be attached to the back of the microwave oven.NOTE: To avoid possible damage to the work surface, cover the work surface.1. Remove any remaining contents from the mic...
