Kenmore 22-80322- Installation Manual

Page 2 - Before You Use Your Microwave; CONTENTS; General information; Attach Mounting Plate to Wall; Installation Instructions

Before You Use Your Microwave CONTENTS General information Important Safety Instructions .................................. 3 Electrical Requirements .......................................... 3 Damage – Shipment/Installation.............................. 4 Parts Included...............................

Page 4 - If the unit is damaged in shipment,; return the; If the unit is damaged by the customer,; repair or; If the unit is damaged by the installer; Some extra parts are included.; HARDWARE PACKET; PART; PARTS INCLUDED; ADDITIONAL PARTS; Shelf; Manual; For some models

PART QUANTITY Wood Screws 2 ( 1 ⁄ 4 “ x 2“) Toggle Bolts (andwing nuts) ( 3 ⁄ 16 “ x 3“) Self-Aligning Machine 3 Screws ( 1 ⁄ 4 “-28 x 3 1 ⁄ 4 “) Nylon Grommet(for metal cabinets) 1 • If the unit is damaged in shipment, return the unit to the store in which it was bought for repairor replacement. • ...

Page 5 - TOOLS YOU WILL NEED; or; MOUNTING SPACE

TOOLS YOU WILL NEED # 1 Phillips screwdriver Pencil Ruler or tape measure andstraight edge Carpenter square(optional) Tin snips (for cuttingdamper, if required) Electric drill with 3 ⁄ 16 “ , 1 ⁄ 2 “ and 5 ⁄ 8 “ drill bits Hammer (optional) Stud finder or Filler blocks or scrapwood pieces, if needed...

Page 6 - Draw a line down the center of the studs.; FINDING THE WALL STUDS; Pull the carton up and off the oven.; Screws; Cut the middle of the outer protective plastic bag to; Exhaust Adapter

PLACEMENT OF THE MOUNTING PLATE 1 Installation Instructions Find the studs, using one of the followingmethods: A. Stud finder – a magnetic device whichlocates nails. B. Use a hammer to tap lightly across themounting surface to find a solid sound.This will indicate a stud location. After locating the...

Page 7 - DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET; THE MICROWAVE MUST BE LEVEL.

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Installation Instructions Plate position flat bottom cabinet Draw a line on theback wall equal to the depth of the frontoverhang. to Cooktop C 3/8" TO EDGE        ...

Page 8 - ALIGNING THE WALL PLATE; Wear gloves; NOTE: DO NOT MOUNT THE PLATE AT THIS; Holes A and B are inside area E. If neither of; at least one wood screw; m ounted; firmly in a stud; to support the weight of the; Set the mounting plate aside

Installation Instructions ALIGNING THE WALL PLATE D. CAUTION: Wear gloves to avoid cutting fingers onsharp edges. Area E Hole A Hole B Centerlinenotches Draw a Vertical Line on Wall from Center of Top Cabinet Draw a horizontal line on wall at thebottom of “Rear Wall Template”. Horizontal Line Horizo...

Page 9 - INSTALLATION TYPES; OUTSIDE TOP EXHAUST; Adaptor in Place for

A INSTALLATION TYPES This microwave oven is designed for adaptation tothe following three types of ventilation: A. Outside Top Exhaust (Vertical Duct)B. Outside Back Exhaust (Horizontal Duct)C. Recirculating (Non-Vented Ductless) proceed to that section. OUTSIDE TOP EXHAUST (VERTICAL DUCT) OUTSIDE B...

Page 10 - Total Ductwork; Maximum duct length:; INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING; diameter duct is acceptable to use.

EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Rectangular-to-Round 5 Ft. (1.5 m) x ( ) = Ft. or m Transition Adaptor* Wall Cap 40 Ft. (12.2 m) x ( ) = Ft. or m 90° Elbow 10 Ft. (3 m) x ( ) = Ft. or m 45° Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m 90° Elbow 25 Ft. (7.6 m) x ( ) = Ft. or m...

Page 11 - Roof Cap; Wall Cap; Total Length; EXTERNAL EXHAUST DUCTING

EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct 12 Ft. (3.6 m) x (1) = 12 Ft. (3.6 m) (6”/15.2 cm Round) Rectangular-to-Round 5 Ft. (1.5 m) x (1) = 5 Ft. (1.5 m) Transition Adaptor* Equivalent lengths of duct...

Page 12 - INSTALLATION OVERVIEW

Place the mounting plate against the wall andinsert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw, make sure the bottom of the mounting platetouch the bottom of the cabinet when pushed flush against the wall and that the plate is ...

Page 13 - EXHAUST; Place the blower unit back into the opening.; with the top of the unit facing up.

USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET You need to drill holes for the top support screws, ahole large enough for the power cord to fit through,and a cutout large enough for the exhaust adaptor. A2. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabi...

Page 14 - Exhaust Adaptor

3 MOUNT THE MICROWAVEOVEN FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NO...

Page 15 - Attach the microwave oven to the top cabinet.; CONNECTING DUCTWORK; furnance; for high temperature applications.

4 Attach the microwave oven to the top cabinet. 8 7 Cabinet Front Cabinet Bottom Shelf Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.) Filler Block Microwave Oven Top Equivalent to Depth of ...

Page 16 - REMOVE BLOWER PLATE

INSTALLATION OVERVIEW B1. Prepare Rear Wall B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Microwave Oven IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to preve...

Page 17 - USE TOP CABINET TEMPLATE

ATTACH THE MOUNTINGPLATE TO THE WALL B3. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET B4. • Read the instructions on the TOP CABINETTEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on theTOP CABINET TEMPLATE. CAUTION: Wear safety goggles when d...

Page 18 - Roll the blower unit 90°

Attach the exhaust adaptor to the rear of theoven by sliding it into the guides at the topcenter of the back of the oven. AFTER: Fan BladeOpenings Facing Back Place the blower unit back into the opening. Replace the blower plate in the same positionas before with the screw. Make sure the screw is ti...

Page 19 - IMPORTANT: If filler blocks are not

Attach the microwave oven to the top cabinet. Installation Instructions 3 MOUNT THE MICROWAVEOVEN B6. FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handleduring installation. NOTE: If your cabinet is metal, use the ...

Page 20 - RECIRCULATING

INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C4.C5. Mount the Microwave Oven IMPORTANT NOTES: • Make sure the screws for the blower motor and blowerplate are securely tightened when they are reinstalled.This will help to prevent excessive vibration. • Make sure the...

Page 21 - MOUNT THE MICROWAVE OVEN; IMPORTANT: Do not grip or use handle; CHECK BLOWER PLATE

Installation Instructions Attach the microwave oven to the top cabinet. Cabinet Front Cabinet Bottom Shelf Filler Block Microwave Oven Top Equivalent to Depthof Cabinet Recess 3 MOUNT THE MICROWAVE OVEN FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OV...

Page 22 - MOUNT THE MICROWAVE; packed with the microwave.; C5. INSTALLING OR CHANGE; lose the microwave door. Plug in microwave

Installation Instructions 5 MOUNT THE MICROWAVE OVEN (cont.) 8 7 Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.) Insert 2 self-aligning screwsthrough outer top cabinetholes. Turn two full tu...

Page 23 - BEFORE YOU USE YOUR MICROWAVE; INST; ring a nd glas s tray in; DDDDDDD; PRODU; Read the; REGIS; U SE; Replace house fuse or turn breaker back on.; FILL OUT PRODUCT R EGISTRATION CAR D

Plug power cord into a dedicated 15- to 20-ampelectrical outlet. Remove all packing material from the microwave oven. 2. Make sure the microwave oven has beeninstalled according to instructions. 1. BEFORE YOU USE YOUR MICROWAVE Ensure properground existsbefore use INST ALLA TION INSTR UCTIONS 3. D G...

Page 24 - Printed in China

Printed in China ＂ 2 / 1 - 4 3/8＂ 3/8＂ 3/8＂ 3/8＂ 13-3/8＂ 8-1/4＂ 2＂ 2＂ 12-1/2＂ 6-1/4＂＂ 2 3 / 7 2 - 9 ＂ 4 / 1 - 4 3/8＂ 3/8＂ 3/8＂ 2＂ 1/2＂ 13-3/8＂ 3/8" TO EDGE   ...

Kenmore 22-80322- Installation Manual

Table of Contents:

Summary

Other Kenmore Models