Kenmore 11075132411 - Installation Manual

6 DRYER DIMENSIONS Front View 50 3 / 4 " (1289 mm) 42" (1067 mm) 28 1 / 4 " (717 mm) 28 1 / 4 " (717 mm) NOTE: Minimum height of leveling legs should be 1/2" (13 mm), or to match the height of the accompanying washer. Side View 29" (737 mm) 40 7 / 8 " (1038 mm) 1 / 2 "...

7 ELECTRICAL REQUIREMENTS – U.S.A. ONLY (SPÉCIFICATIONS ÉLECTRIQUES – ÉTATS-UNIS SEULEMENT) ELECTRICAL REQUIREMENTS It is your responsibility: ■ To contact a qualified electrical installer. ■ To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ...

8 4-wire receptacle (14-30R) ELECTRIC DRYER POWER HOOKUP – CANADA ONLY ELECTRICAL REQUIREMENTS It is your responsibility: ■ To contact a qualified electrical installer. ■ To be sure that the electrical connection is adequate and in conformance with Canadian Electrical Code, C22.1-latest edition and ...

9 3/8" NPT dryer pipe NOTE: For a garage installation, the gas pipe height must be an additional 18" (460 mm) from the fl oor. GAS SUPPLY CONNECTION REQUIREMENTS ■ Use an elbow and a 3/8" fl are x 3/8" NPT adapter fi tting between the fl exible gas connector and the dryer gas pipe, a...

10 2. Screw in leveling legs Using a wrench and tape measure, screw leveling legs into leg holes until bottom of foot is approximately 1/2" (13 mm) from bottom of dryer (so that the dryer height matches that of the accompanying washer).Now stand the dryer on its feet. Slide the dryer until it is...

11 D C B A 1. Attach power supply cord strain relief Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections (C) into the hole below the terminal block opening (B) so that one tab is pointing up (A) and the other is poin...

12 Remove center terminal block screw (B). Remove neutral ground wire (E) from external ground conductor screw (A). Reinstall ground conductor screw (A). B A E 1. Prepare to connect neutral ground wire and neutral wire B C E 2. Connect neutral ground wire and neutral wire Connect neutral ground wire...

13 3. Connect remaining wires Connect remaining wires to outer terminal block screws. Tighten screws. Finally, reinstall terminal block cover. Secure cover with hold down screw. Now, go to “Venting Requirements.” 2. Connect neutral wire Connect neutral wire (white or center) (C) of power supply cord...

14 Put direct wire cable through the strain relief. The strain relief should have a tight fi t with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable. 2. Attach direct wire cable to strain relief 3-wire direct connection:Go to “3-wire Direct...

15 Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Finally, reinstall terminal block cover. Secure cover with hold-down screw. Now, go to “Venting Requirements.” 5. Connect remaining wires...

16 B C E 2. Connect neutral ground wire and neutral wire Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cable under center terminal block screw (B). Tighten screw. 3. Connect remaining wires Place hooked ends of remaining wires under outer termina...

17 Venting Requirements WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid ...

18 Plan Vent System Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B B C D E E F G H A A. Dryer B. Elbow C. Wall D. Exhaust hood E. Clamps F. Rigid metal or flexible metal vent G. Vent length necessary to connect e...

19 CONNECT INLET HOSES For non-steam models, skip to “Connect Vent.” The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 2. Connect vent to exhaust hood Vent must fi t over the exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp. Run...

20 5. Attach long hose to dryer fi ll valve and tighten coupling 7. Check for leaks Check for leaks around “Y” connector, faucets, and hoses. 6. Turn on cold water faucet Check that the water faucet is turned on. CONNECT VENT 1. Connect vent to exhaust outlet Using a 4" (102 mm) clamp, connect v...

21 LEVEL DRYER Not Level LEVEL Not Level Check levelness of dryer from side to side. Repeat from front to back. NOTE: The dryer must be level for the moisture sensing system to operate correctly. 1. Level dryer 2. Adjust leveling legs If dryer is not level, prop up using a wood block. Use wrench to ...

22 REVERSE DOOR SWING (OPTIONAL) NOTE: Magnetized screwdriver is helpful. Place towel on top of dryer to avoid damaging the surface. 1. Place towel on dryer 2. Remove bottom screws Open dryer door. Remove bottom screws from dryer cabinet side of hinges. Loosen (do not remove) top screws from dryer c...

24 12. Insert screws in hinge holes on dryer cabinet NOTE: Two people may be needed to reinstall door. Insert screws into the bottom holes on left side of dryer cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slo...