Page 2 - FOREWORD/IMPORTANT INFORMATION; SWITCHING THE RECEIVER OFF
2 FOREWORD/IMPORTANT INFORMATION Dear customer, this Operating Manual is intended to help you make the fullest use of the extensive range of functions offered by your new HDTV satellite receiver. We have tried to make the operating instructions as easy as possible to understand, and to keep them as ...
Page 3 - nd out how to obtain the source code for the program at:; DISPOSAL INSTRUCTIONS
3 FOREWORD/IMPORTANT INFORMATION The channels available on the satellites and transponders are subject to continual change. In such cases, it is necessary to re-adjust the channels as the factory preset programming corresponds to the situation on the date of manufacture. The information for these se...
Page 4 - RECEIVER FEATURES/PRODUCT PACKAGE; PRODUCT PACKAGE; The update time cannot be changed.
4 RECEIVER FEATURES/PRODUCT PACKAGE - Receiver UFS 902 (silver or black) - Infra-red remote control - Batteries- HDMI cable - Operating manual - Safety instructions - Scart cable - Mains power cable PRODUCT PACKAGE The UFS 902 HDTV receiver is suitable for the reception of digital satellite TV and r...
Page 5 - CONTENTS
5 CONTENTS FOREWORD/IMPORTANT INFORMATION .................................................................................. 2 RECEIVER FEATURES/PRODUCT PACKAGE ............................................................................ 4 CONTENTS ......................................................
Page 7 - CONTROLS, DISPLAYS AND CONNECTIONS; Front panel controls and displays; Rear panel controls and displays; VIEW OF REAR PANEL
7 CONTROLS, DISPLAYS AND CONNECTIONS This section provides a brief description of all the controls, displays and connections. The button symbols presented here can also be found in the description of the operating steps. USB 2.0 5V... 500 mA max Front panel controls and displays 1. Common Interface ...
Page 8 - CONNECTION AND SETUP; The quality of the reception signal depends on this connection!; RECEPTION REQUIREMENTS
8 CONNECTION AND SETUP The following section is intended specifi cally for specialist dealers. You need not refer to this section unless you are carrying out the installation yourself. The “Connection Examples” section provides a sample confi guration.Do not connect the receiver to the power supply ...
Page 9 - TV CONNECTION
9 CONNECTION AND SETUP Connect the satellite receiver (HDMI or alternatively TV Scart socket) and the TV set using a HDMI or Scart cable (see “Connection Example”). If your TV is stereo, you can receive the sound in stereo via the HDMI or Scart connection. For system reasons, the same video signals ...
Page 10 - REMOTE CONTROL
10 REMOTE CONTROL Sound on/off ... Enter numbers for channels, timer etc. Open main menu, leave the menu and return to the TV picture (red) Open favourites selection ! (green) 1x open display of 4:3 programmes, 2x open HDMI/YUV format % Volume Leave menu step by step Change channel in the programme ...
Page 11 - REMOTE CONTROL RC 660
11 REMOTE CONTROL REMOTE CONTROL RC 660 The RC 660 remote control supports up to four units which are supplied as standard with the RC 660. First switch off all other receivers at the power switch. 1. Set-up using menu On the UFS 902 the remote control code on the “Service Menu”, “Remote Control Cod...
Page 12 - FIRST INSTALLATION
12 FIRST INSTALLATION Before using your receiver for the fi rst time, read the “Safety Instructions” and “Connection and Setup” sections. The “Connection Examples” section provides a sample confi guration. Do not connect the receiver to the power supply until all installation work has been properly ...
Page 13 - TV aspect ratio
13 The following display appears: Use the buttons here to select the settings for your TV set. When doing this, refer to the operating instructions for your TV set! Video Output via Select here the connection on the receiver to which you have connected your television. Either SCART or HDMI/YUV FIRST...
Page 14 - System
14 FIRST INSTALLATION System Select the setting here to match your reception system using the buttons. You have the following options: - DiSEqC™1.0- One Cable - LNB only If your reception system supports DiSEqC™, in “System” select “DiSEqC™1.0” (is used for switch-over from one received satellite to...
Page 15 - Number of Satellites; Satellite and Position
15 Number of Satellites Use the buttons to select how many satellites (max. 4) you would like to receive with your reception system. The following display appears (example): FIRST INSTALLATION: DiSEqC™1.0 Use the buttons to select the fi rst satellite slot. Press to open the menu for the satellite s...
Page 17 - FIRST INSTALLATION: LNB ONLY; LNB Type
17 FIRST INSTALLATION: LNB ONLY Satellite and Position Use the buttons to select the desired satellite whose signal is to be received by the tuner. When you have selected your desired satellite, use the buttons to switch to the selection of the “LNB Type”. LNB Type Here use the buttons to select the...
Page 18 - Test transponder
18 FIRST INSTALLATION: LNB ONLY user-defi ned:If you choose not to use a universal LNB, you must here set the frequency ranges for which your LNB was confi gured. Use the buttons to select the frequency range to be changed (low, high or limit frequency). Use the buttons or the number buttons to set ...
Page 19 - FIRST INSTALLATION: One Cable
19 FIRST INSTALLATION: One Cable Use the buttons here to select “One Cable” as the “System”. Press the button to move to the next menu item. The following display appears: Number of Satellites Use the buttons to select how many satellites (max. 2) you would like to receive with your reception system...
Page 22 - Connected equipment; Selection “user-defi ned”; nd the necessary information (transmission frequencies) in the
22 Connected equipment Use the buttons to select the type of system to which they are connected or the single-cable system components fi tted (refer to the manuals, instructions and notes for the system and the system components). Available options: - user-defi ned- KATHREIN UAS 481 (single-cable fe...
Page 27 - FIRST INSTALLATION: Channel search
27 Execute Channel search Use the buttons to select (yes or no) whether you wish to start a channel search. It is not essential to start a channel search; instead you can use the factory pre-programmed channels. However the channels do change from time to time (e.g. their frequencies change), which ...
Page 28 - FIRST INSTALLATION: CHANNEL SEARCH; update time on
28 Local time offset (UTC) Use the buttons to set the time zone variation from UTC (formerly GMT) (e.g. for Germany +1 hour). Use the buttons to switch to the “Automatic clock change” fi eld. Use the buttons to select whether the receiver should automatically change over between summer and winter ti...
Page 29 - OPERATING INSTRUCTIONS; MENU CONCEPT
29 OPERATING INSTRUCTIONS The structure of the menu concept is based on logical operating sequences. The programme showing on the current selected channel always appears in the top right-hand corner of the screen. You will fi nd detailed descriptions of the selected menu items in the relevant sectio...
Page 30 - MENU TREE; Main menu; Open using the
30 MENU TREE OPERATING INSTRUCTIONS Main menu Open using the button
Page 31 - LANGUAGE SELECTION - OSD
31 OPERATING INSTRUCTIONS The language for the on-screen display is set as follows: → → Language Setting → → → English → Available options: German, English, French, Italian, Spanish, Czech, Dutch, Polish, Turkish and Russian. After you have performed the settings, press the or the button to exit the...
Page 32 - CHANNEL OSDS; TV CHANNEL OSD; PROGRAMME INFORMATION
32 ON-SCREEN DISPLAYS (OSD) The channel OSD is displayed for a few seconds each time the channel is changed (this feature can be changed on the “Settings”, “Customize Screen Menu” menu) or displayed continuously by pressing the button. The OSD for the current radio channel has the same layout. Chann...
Page 33 - OPENING OPTIONS CHANNEL
33 If the channel OSD contains the following icon , this is a portal channel. Press the " (yellow) button to display the channels available on this portal (such as matches on a specifi c day of play). In this example three “sub-channels” are available for selection within this portal channel. Se...
Page 35 - Selection and sorting options:
35 Selection and sorting options: - Press the (red) button to open the favourite list selection. The buttons allow you to scroll through the existing favourite lists. - Press the ! (green) button to return to the overall list (all satellites). Use the buttons to choose between the received satellite...
Page 36 - EPG - ELECTRONIC PROGRAMME GUIDE; OPENING THE EPG
36 EPG - ELECTRONIC PROGRAMME GUIDE OPENING THE EPG The EPG is opened by pressing the button. Each time the EPG is opened, you will automatically be shown the “Current” view, irrespective of which view you were shown the last time you left the EPG. The following display appears (example): Channel nu...
Page 37 - “CURRENT” VIEW
37 EPG - ELECTRONIC PROGRAMME GUIDE Selection options: - (red) button Open the timer list (display of all pre-programmed recordings) - button Jump the “Current” view forwards by 15 minutes - " (yellow) button Open a preview of the currently highlighted channel - # (blue) button Open the category...
Page 39 - CATEGORIES VIEW
39 EPG - ELECTRONIC PROGRAMME GUIDE CATEGORIES VIEW The “Categories” view can be opened at any time in EPG by pressing the # (blue) button. In the “Categories” view you can see all programmes sorted by category and starting time.The following categories are available for selection: Movies, Series, S...
Page 40 - SEARCH FUNCTION
40 SEARCH FUNCTION The search function can be opened at any time in EPG by pressing the button. The search function allows you to search for programmes based on their additional information or their name. Use the number buttons to enter the desired search expression (see also “Operating Instructions...
Page 41 - REMINDER FUNCTION (CHANGE OVER TO PROGRAMME)
41 EPG - ELECTRONIC PROGRAMME GUIDE ADDITIONAL INFORMATION (i BUTTON) The additional information can always be opened by pressing the button whenever the “i symbol” appears in front of the programme name (see screenshot on the right). First however the channel must be selected. The following display...
Page 43 - RECORDING ONCE ONLY
43 EPG - ELECTRONIC PROGRAMME GUIDE RECORDING ONCE ONLY Use the buttons to select the recording mode “once” (see screenshot “Recording (timer)” section). Use the buttons to switch to the selection fi eld “Date” and use the buttons to select the desired recording day. Use the buttons to switch to the...
Page 44 - RECORDING WEEKLY; pressing the
44 RECORDING WEEKLY Use the buttons to select the recording mode “weekly” (see screenshot below). Use the buttons to switch to the selection fi eld “Start” and use the buttons or the number buttons to select the desired recording start time. Use the buttons to switch to the selection fi eld “End” an...
Page 45 - SERIES RECORDING
45 Use the buttons to switch to the selection fi eld “End” and use the buttons or the number buttons to select the desired recording end time. When all settings have been made, press the button to save the recording settings. You can view the scheduled recording in the timer list view of the EPG (se...
Page 46 - TIMER LIST VIEW
46 EPG - ELECTRONIC PROGRAMME GUIDE TIMER LIST VIEW The “Timer list” view can be opened at any time in EPG by pressing the (red) button. The timer list view shows you all the recordings that are scheduled. The buttons allow the recordings to be sorted into “once” or “repeated” recordings. The cursor...
Page 47 - COMMON INTERFACE; Smartcards and CA module are not included with this product!; IMPORTANT INFORMATION
47 COMMON INTERFACE Always follow the operating instructions from your pay TV provider and the instructions supplied with the Smartcard and the CA module! Smartcards and CA module are not included with this product! The cards and modules are issued by the respective pay TV providers, and contain the...
Page 49 - TELETEXT
49 TELETEXT When you press the button, the receiver processes the broadcast Videotext/Teletext service, if available, for your TV set to display, even when the signal is encrypted. During the search, the page which is being searched for is displayed in the top left-hand corner with the time and date...
Page 50 - EDITING CHANNEL LIST; SELECTION OF THE LIST/CHANNEL TO BE EDITED
50 EDITING CHANNEL LIST Select the “Edit TV-Channellist” menu using the menu button , the buttons on the main menu and . SELECTION OF THE LIST/CHANNEL TO BE EDITED Press the # (blue) button to switch between the TV and radio channel lists. Radio channels are edited in the same way as TV channels. Ed...
Page 51 - EDITING LIST/CHANNELS; Start Blockselection:
51 EDITING LIST/CHANNELS When you have selected the channel or channel list to be edited, press the (red dot) button to open the edit menu. You have the following edit options: - Move: Channel can be moved within the current list to another channel slot - Delete: Delete the channel from the current ...
Page 52 - DELETING CHANNELS; SKIPPING CHANNELS
52 DELETING CHANNELS Use the buttons to select the channel to be deleted on the channel list you have selected. Press the button to open the edit menu and use the buttons to select the “Delete” function. Confi rm the command by pressing the button. EDITING CHANNEL LIST SKIPPING CHANNELS Use the butt...
Page 54 - EDITING FAVOURITE LISTS; Remove from favoritelist:; REMOVING FROM FAVOURITE LIST
54 EDITING CHANNEL LIST EDITING FAVOURITE LISTS When you have selected the favourite list to be edited (open using the (red) button and select using the buttons), press the (red dot) button to open the edit menu. You have the following edit options: - Remove from favoritelist: The channel will be re...
Page 58 - the
58 Newly found channels are identifi ed with the designation “New” after the channel name. After completion of the search, you will see the following message (example): Press the button. You will be asked whether you wish to save the changes or not. Selection is performed using the buttons and is co...
Page 60 - Network Search; CHANNEL SEARCH WITH SERVICE ID; Satellite
60 Network Search Use the buttons (On/Off) to select whether a network search should be performed. If you set the network search to “Off”, only the factory stored transponders of the satellites you previously selected will be searched for new as yet unlisted channels.If you set the network search to...
Page 62 - PARENTAL CONTROL; LOCKING MAIN MENU
62 PARENTAL CONTROL Select the “Parental Control” menu using the menu button , the buttons on the main menu and . You are now prompted to enter the PIN code (factory default setting: 0000). After entering the PIN using the number buttons the following display appears: Select the parameters to be cha...
Page 63 - SETTINGS
63 SETTINGS The selected menus, sub-menus and positions, as well as the parameters to be set, are each highlighted in colour. The menus are largely self-explanatory. Pay attention to the bar at the bottom of the on-screen display. These provide information on what to do next. Select the “Settings” m...
Page 64 - TV SETTINGS; Video Output via; Audio format via HDMI; SCART; or
64 TV SETTINGS SETTINGS Use the buttons here to select the settings for your TV set. When doing this, refer to the operating instructions for your TV set! Video Output via Select here the connection on the receiver to which you have connected your television. Either TV aspect ratio Here you select t...
Page 65 - Auto Dolby Digital OUTPUT; CUSTOMISING SCREEN MENU; FUNCTIONS
65 Auto Dolby Digital OUTPUT Here you can select whether the receiver should automatically output the Dolby Digital signal (if this is transmitted). Audio Delay (setting not currently available!) Here you can set a delay in milliseconds, if the sound output from your receiver is out of synch with th...
Page 66 - CHANNEL OSD DURATION
66 SETTINGS Use the buttons to select the time after which you want the channel OSD to disappear automatically. The selections available are “Off”, 1, 2, 3, 4, 5 or 6 Seconds. CHANNEL OSD DURATION Use the buttons (On/Off) to specify whether the volume bar is displayed when adjusting the volume. DISP...
Page 67 - DATE AND TIME; Automatic time setting
67 SETTINGS DATE AND TIME COMMON INTERFACE See “Common Interface” section ANTENNA CONFIGURATION See “First Installation” section, pages 14ff Local time offset (UTC) Use the buttons to set the time zone variation from UTC (formerly GMT) (e.g. for Germany +1 hour). Use the buttons to switch to the “Au...
Page 68 - SERVICE MENU; SOFTWARE UPDATE
68 SERVICE MENU Select the “Service” menu using the menu button , the buttons on the main menu and . The following display appears: Current software version Last update run SOFTWARE UPDATE You can also check manually whether new software is available. Use the buttons to switch to “Software Update“ a...
Page 69 - Updating software
69 SERVICE MENU Also note the bars at the bottom of the on-screen display! These provide information on what to do next. Updating software If new software is available (but only then), use the buttons (No/Yes) to select whether you wish to load the new software that is available. If you are unsure w...
Page 70 - FACTORY RESET
70 FACTORY RESET Select the “Service” menu using the menu button , the buttons on the main menu and . Use the buttons to switch to “Factory Reset” and press the button. The following display appears: Press the button to load the factory default settings. The channels and favourite lists remain uncha...
Page 71 - USB DEVICE MANAGEMENT; REMOTE CONTROL CODE
71 USB DEVICE MANAGEMENT This function is not currently supported/activated. SERVICE MENU REMOTE CONTROL CODE Select the “Service” menu using the menu button , the buttons on the main menu and . Use the buttons to switch to “Remote Control Code” and to open press the button. The following display ap...
Page 72 - OPERATING FROM THE FRONT PANEL; BACKUP OPERATION; buttons
72 OPERATING FROM THE FRONT PANEL If you have misplaced your remote control, or if the batteries are fl at, you can still operate your receiver from the front panel. BACKUP OPERATION Because there are no number buttons, no password/PIN-protected functions can be displayed. There are four buttons on ...
Page 73 - TECHNICAL APPENDIX; FEATURES
73 TECHNICAL APPENDIX FEATURES Q Reception of digital satellite TV channels and radio programmes in DVB-S and DVB-S2 transmission standards Q Video decoding of MPEG-2 and MPEG-4/H.264 signals Q 12-character alphanumerical display shows channel names and transmitter information Q 4,000 channel memory...
Page 75 - SCART SOCKET ASSIGNMENT
75 Signal Pin no. TV Audio right output 1 X Audio right input 2 Audio left output 3 X Audio earth 4 X Blue earth 5 X Audio left input 6 Blue signal 7 X Switching voltage 8 X Green earth 9 X Data signal 10 Green signal 11 X Data signal 12 Red earth 13 X Data earth 14 Red signal (C) 15 X Blanking sign...
Page 76 - CONNECTION EXAMPLE; Scart; Dolby digital system
76 CONNECTION EXAMPLE TECHNICAL APPENDIX UFS 902 Scart USB 2.0 5V... 500 mA max Dolby digital system Hi-fi system
Page 77 - EXAMPLES single-cable systems; Single-cable switching matrices
77 TECHNICAL APPENDIX EXAMPLES single-cable systems Sat-ZF950-2150 MHz UAS 484 Terrestrische Antenne **) ESU 33 Single RTL Telev ision 712 ESU 33 Single RTL Telev ision 712 ESU 33 Single RTL Telev ision 712 ESU 33 Single RTL Telev ision 712 terr . H low/0kHz V 1-4 V high/22kHz H 1 = SCR(0) 1400 MHz ...
Page 78 - Single-cable feed system
78 TECHNICAL APPENDIX UAS 481 Single-cable feed system ERA 14 ERA 14
Page 79 - Single cable matrix
79 EBC 10 Zum oder über EN 5 2 xQuatro-LNBUAS 484 EXU 908 Made in Germany 230V~ / 32W KLASSE CLASS 20510016 Receiver 1 ... 8 Receiver (No.): Frequency (MHz ): SCR-Adress: 1 2 3 4 5 6 7 8 1284 1400 1516 1632 1748 1864 1980 2096 0 1 2 3 4 5 6 7 Error Power T err. Pos B V high V low H low H high 18V / ...
Page 80 - SHORT TECHNICAL GLOSSARY
80 SHORT TECHNICAL GLOSSARY AC3 Output for Dolby Digital signal ASTRA SES (Société Européene des Satellites) satellite system. Analogue and digital transponders in the frequency range 10.7-12.75 GHz. AV programme slot Preferred programme slot on TV set for external connections such as Scart and HDMI...
Page 84 - SUBJECT INDEX
84 ADDITIONAL INFORMATION (i BUTTON) ................................................................................ 41 ALPHANUMERIC ENTRIES .................................................................................................... 31 ANTENNA CONFIGURATION ...................................
Page 86 - TROUBLESHOOTING; A selection of troubleshooting tips is offered below.; Problem
86 TROUBLESHOOTING In the event of a malfunction, fi rst check all the cable connections and operating states:1. Receiver and TV set power plugs are connected to wall socket2. Antenna cables on receiver input3. Receiver and TV set correctly connected by a Scart or cinch cable4. Audio connections are...
Page 87 - SERVICE
87 SERVICE If, despite studying this operating manual, you still have questions about getting started with the unit or using it correctly, or if unexpected problems occur, please contact your specialist dealer.
