Kathrein HDZ 100 - Manual - manualsarea.com

Page 2 - CONTENTS

2 CONTENTS ............................................................................................................................... 2 FOREIGN LANGUAGE INSTALLATION MANUALS/SERVICE ...................................................... 3 ADDRESS OF THE SERVICE CENTRE .............................

Page 3 - FOREIGN LANGUAGE INSTALLATION MANUALS/SERVICE; ADDRESS OF THE SERVICE CENTRE

3 Dear Customer, Chère Cliente, Cher Client, Gentile cliente, Estimado cliente, GB You can obtain an English version of our installation instructions from our representatives in your country (http://www.kathrein.de/include/kontakte_groups_eng.cfm?kontinent=1&gruppe=SAT) or download one from our ...

Page 4 - HDZ 100 COMPONENTS/SCOPE OF SUPPLY; HDZ 100 SCOPE OF SUPPLY

4 HDZ 100 COMPONENTS/SCOPE OF SUPPLY • Cover with two gaskets and four captive screws • Sealing plug • Bottom half of the casing with gasket and six plugs • Three fastening screws HDZ 100 SCOPE OF SUPPLY • Protective casing for cable interfaces on the caravan roof for Kathrein rotary antenna systems...

Page 5 - PROPER USE; PROPER USE (USE FOR THE INTENDED PURPOSE)

5 PROPER USE The HDZ 100 roof gland protects the cable connection point and the roof gland point when laying cables from CAP systems on the caravan or mobile home roof. The gland seatings are designed for two cables (Ø 5 mm) and one cable (Ø 6.5-7 mm). Any use other than that specifi ed above will v...

Page 6 - SAFETY INSTRUCTIONS - IMPORTANT NOTES; Safety during installation work; Proper installation and safety

6 SAFETY INSTRUCTIONS - IMPORTANT NOTES Safety during installation work When carrying out installation work in locations where there is a risk of falling, take appropriate safety precautions, e.g. use of a working platform. Make sure that the vehicle roof is suffi ciently strong and stable to carry ...

Page 8 - INSTALLATION EXAMPLES; BASIC VARIANTS

8 INSTALLATION EXAMPLES BASIC VARIANTS Roof gland with cable interface Roof gland without cable interface Cable continuation with cable interface Note: For the CAP 600/700 units there are always two cables emerging from the turntable. For the CAP 900 unit there are always three cables emerging from ...

Page 9 - REQUIRED TOOLS AND EQUIPMENT; INSTALLATION AND CONNECTION; NECESSARY SPACINGS WHEN USING CABLE DUCTS

9 • Circular cutter, Ø 38 mm • Cross-head screwdriver for M4 screws • Power drill • Twist drill Ø 2.5 mm • Knife• Round fi le or emery paper • Sikafl ex ® 291 sealant (included in the CAP turntable scope of supply. Comply with the respective safety instructions for the sealant) • If required for the...

Page 10 - INSTALLATION STEPS; ROOF GLAND VARIANT

10 INSTALLATION AND CONNECTION INSTALLATION STEPS ROOF GLAND VARIANT 1. In the centre of the intended position of the cable outlet spigot, drill the opening for the cable gland with a circular cutter (Ø: 38 mm). Deburr the hole with a round fi le or emery paper (see illustration on the right). 2. Pr...

Page 12 - CABLE CONTINUATION VARIANT

12 CABLE CONTINUATION VARIANT 1. First cut the cylindrical spigot off the underside of the casing. There are two ways of doing this: - use a sharp knife to cut through the wall between the base of the casing and the spigot (see illustration on the right) or 11. Use the plugs supplied to seal the cab...

Page 16 - FOR YOUR NOTES

Internet: http://www.kathrein.deKATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 P.O. Box 100 444 • 83004 Rosenheim GERMANY 936.3442/-/0908/ZWT - T echnical data subject to change. FOR YOUR NOTES

Kathrein HDZ 100 - Manual

Table of Contents:

Summary

Other Kathrein Models