JVC K3-R - Manual
JVC K3-R – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Installation & Operation; Manual Switch Control; AB Switch Status Indication; ON; Indicates the power supply source is connected.
- Page 3 – Power Supplies Modules; Internal -48VDC Power Supply
- Page 4 – Alarm Connector; Pin 6 NO; Input Power
- Page 5 – Control Modules; WEB; Telnet; Installation; controller provides the following connections:; Serial Port
- Page 7 – Setting the IP address using ARP; Delete the entry from the ARP cache by typing:; Setting IP Address with Telnet; Select Run...Telnet; The factory default password is:; PASS
- Page 9 – IP Settings; Setting IP address via Serial Port; Utility setip.exe is available from Dataprobe’s website at; Setting other Parameters; Via the Serial Port (or telnet on the; Location Name; three AB card slot positions of the 16 displayed are used in the K3.; password then enter the new password twice as prompted.
- Page 10 – K3 1RU AB Switch
- Page 11 – . By removing power to the the K3 chassis momentarily and; Operation
- Page 14 – Telnet and Serial Port; into your Telnet application program
- Page 15 – SNMP Manager Control
- Page 16 – cr; Gang Control Expansion; R Gang Expansion Card; Expansion Connector Pinout; Pin Designation
- Page 18 – Specifications; Switch Interfaces; Three 25 Pin D Subminiature, Female Connectors.; Physical
- Page 19 – MIB Outine; three AB; Mib Tree
- Page 20 – MIB Definitions; This variable is not directly accessible.
- Page 21 – ok; Trap Definitions
- Page 22 – TECHNICAL SUPPORT, RETURNS and WARRANTY; Authorized Dataprobe Reseller,; WARRANTY
Technical Support: 201-934-5111
Main: 201-934-9944
[email protected]
Website: dataprobe.com
General Description
The K3 Series A/B Switching system provide up to 3 AB switches in a 1.75 in rack mount chassis for 19”
Equipment cabinets. Each switch allows a common circuit (COM) to be switched to either of two circuits,
designated A and B. The switches can be controlled locally with a front panel toggle switch and remotely
by; contact closure, or thru a Serial port and Ethernet connection using Telnet, SNMP, or a Web browser.
Modular System
The K3 System consists of the K3 Chassis, Model K3-R and Power, Control and A/B Switch options.
The following table illustrates the available K3 components available at the time of printing. Additional
options may be available; contact Dataprobe.
SKU Model
Description
Base
1150100 K3-R
K3
Chassis
Control
1340062
C-AB-16-R
IP and Serial Control Card, Individual Switch Control
1340065
C-AB-1-R
IP Control Card, Gang Control
1340063
G-AB-1-R
Gang Expansion or GPI Control
Power
1930077
PS-R1-WRI
Internal AC Power Supply 100-240VAC
1930078
PS-R1-48
Internal -48VDC Power Supply
1930079
PS-R1-224
Dual External 24VDC Power Supply. For use with External AC Supply
1930076
PS-WRI-4
External A/C Power Supply
A/B
1110100
AB-R-D25
25 Pin D Subminiature, all 25 pins supported
1110101 AB-R-RJ8
8 Wire Modular Jacks; All leads switched. Supports RJ48C, RJ48S, RJ45 and
all 8 position modular jack specifications, up to16Mhz
1110102
AB-R-2RJ8
Same as above with two ganged switches.
1110103 AB-R-NET
8 Position, 8 Wire Modular Jacks; All leads switched; Supports 10/100/1G
Ethernet Network specifications.
1110104 AB-R-T50
50 Pin Telco (Amphenol) connector. All 50 Leads Switched. Dual Height
Switch must be in Slot 1
1110105 AB-R-M34
34 Pin M Type (V.35) connector. 23 leads switched. Dual Height Switch must
be in Slot 1
1920028
AB-FP
Blank Panel for unused A/B Slots. Required for FCC and CE marking
K3 Series
1U Rack Mount A/B Switches
K3_system_v070607e
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
K3 System Page 2 Installation & Operation K3 Chassis The K3 Chassis holds the Power, Control and A/B Switch modules for the K3 system. It installs in a standard 19” EIA equipment cabinet, requiring 1.75” (1U) of rack height. K3 systems are preconfigured and tested in the factory. All Control, Po...
K3 System Page 3 Power Supply 1930077 Converts 110/ 220 /240 VAC to 24VDC Single Slot Redundant Capable Input Power Nominal : 120/240 VAC 50/60 Hz Range : 100 - 240 VAC Watts: 50 Fusing: 2 A Environmental Operating: 0 C - +65C Physical AC Input connector: IEC 320 (C14) on rear panel Alarm / Expansio...
K3 1RU AB Switch Page 4 Alarm Connector Alarm Connection on each power supply provides status information on the condition of the supply. 9 Pin Dsubminiature Pin 6 NO Pin 6 shorts to Pin 7 when the Power Supply is Non-Operational Pin 7 COM Pin 8 NC Pin 8 shorts to Pin 7 when the Power Supply is Oper...
