Jonsered SM 2186 - Manual

English – 5 SAFETY REGULATIONS WARNING!A one-man sawmill can be adangerous tool that can causeserious or fatal injury if usedincorrectly or carelessly. It is veryimportant that the person using theone-man bandsaw reads andunderstands the content of thismanual. Safety Regulations WARNING!Always ensur...

6 – English SAFETY REGULATIONS WARNING!The one-man sawmill must neverbe used if any of the safetydevices or guards is damaged ordoes not work. WARNING!The fuel used in the one-mansawmill has the followinghazardous properties: 1. The fluid, its vapour, and its exhaust fumes are poisonous. 2. Can caus...

English – 7 One-man sawmill chain saw engine The one-man sawmill consists of two main par ts:• The carriage with engine and saw• Rails 1. Rail sections (2)2. Log lifter3. Timber suppor ts (short and long)4. Log bolster5. Log lock6. Adjustment nut7. Saw carriage8. Protective loop9. Vibration damping ...

8 – English DESCRIPTION One-man Sawmill Electric Motor The one-man sawmill consists of two main parts:• The carriage with motor and saw• Rails 1. Rail sections (2)2. Log lifter3. Timber supports (short and long)4. Log bolster5. Log lock6. Adjustment nut7. Saw carriage8. Protective loop10. Skid rail1...

English – 9 DESCRIPTION One-man sawmill with electric motor and feed Tools and operator’s manual A. Open ended spanner 13-15 mmB. Open ended spanner 17-19 mmC. Socket spannerD. Combination spanner 13-19E. Combination spannerF. Allen key 6 mmG. Allen key 4 mmH. This operator’s manual The one-man sawm...

English – 11 DESCRIPTION FIG. 6 FIG. 7 FIG. 8 FIG. 5 Chain oil tank (FIG. 5) Chain sawmill with electric motor On the saw carriage for sawmills that are fitted with anelectric motor, the oil tank (25) for chain oil is locatedon the electric motor. The chain oil is pumped via ahose by a chain oil pum...

12 – English DESCRIPTION Motors Chain saw engine (FIG. 9) The one-man sawmill is powered by a standard chainsaw ranging from 65 cm 3 up to 95 cm 3 . The chain saw is mounted on a vibration-free plate (9), where it isscrewed into the bar mounting with two spacers andscrews (15). The saw’s speed is co...

English – 13 DESCRIPTION Folding Stops (C) There are a number of folding stops for the log on theleft-hand side of the rails. To increase usability, thestops come in two different lengths. Log Locks (D) The log locks consist of a cam with handle, housed ina moveable unit. The locks are used to secur...

14 – English DESCRIPTION Rail Stop Rail stops are fitted at the ends of the rails (A). Thestop is mounted using a bolt from the side of the rail. Rail Guard The saw carriage is equipped with four rail guardsthat run above the rails. The rail guards have thetasks of keeping the rails clean and preven...

English – 15 DESCRIPTION Safety Devices The one-man sawmill is fitted with a number of safetydevices, which are described under the headingsbelow. WARNING!The one-man sawmillmust not bestarted if any of the safety deviceshave been removed, are defective, orare not working. ! Saw chain guard (FIG. 17...

16 –English INSTALLATION Bolted joint Adjustable foot Aligning the rails Installation Site The one-man sawmill with petrol engine should beinstalled outdoors.There should be space to lay out timber and sawnwood. Rails Place the rail sections after each other on thetransverse wooden beams, which are ...

20 –English INSTALLATION One-man sawmill with chain sawengine Adjusting the bar The bar must be adjusted so that it is parallel with thelog bolsters and with the rails. This is done using thenuts under the vibration damping plate. Set the bar sothat it is parallel with the rails by positioning a str...

English – 21 FUEL HANDLING WARNING!The fuel used in the one-mansawmill has the followinghazardous properties: 1. The fluid, its vapour, and its exhaust fumes are poisonous. 2. Can cause skin irritation. 3. Is highly inflammable. Fuel chain saw engine Fuel Safety The following are absolutely forbidde...

22 – English Two-stroke oil • For the best results use JONSERED two-stroke oil, which is especially developed for chain saws. Mixingratio 1:50 (2%). • If JONSERED two-stroke oil is not available, you may use another two-stroke oil of good quality thatis intended for air cooled engines. Contact yourd...

English – 23 STARTING AND STOPPING WARNING!Observe the following before star-ting the engine: • The engine must be mounted in the sawmill before starting.Otherwise the clutch can comeloose and cause personal injuries. • Keep people and animals well away from the risk zone. ! Starting a cold chain sa...

English – 25 Securing the Log WARNING!Exercise care during all log hand-ling. Heavy lift! Wear boots orshoes fitted with steel toecaps. 1. Fold up the stops (C) on the left-hand side of therails. 2. Roll the log up against either the long or the shortlog support, depending on the timber dimensions. ...

26 – English 1. Place the log on the rails facing the folding logsupports (FIG. 44). 2. Set the height of the bandsaw blade using thecrank (11). 3. Clean any sand from the log, if necessary. Thisresults in less wear. 4. Check and if necessary top up the chain oil tankwith chain oil on each sawmill. ...

English – 27 WARNING!Check during sawing that the chaindoes not hit the folding stops orlog lock. WARNING!The saw carriage must not bemoved backwards while the chainis in motion. The log could comeloose and cause personal injury. Starting the Petrol Engine 1. Start the engine. See page 23. Starting ...

English – 29 MAINTENANCE WARNING!The one-man sawmill must bedisconnected from power duringall maintenance work. Always usepersonal protective equipment. ! FIG. 53 FIG. 52 Clutch drum When replacing the clutch drum on the chain saw, seethe chain saw operator’s manual. The clutch drum on the chain saw...

30 – English MAINTENANCE FIG. 53 Saw chain WARNING!The chain is sharp and can causecuts. It can cause personal injurywhen handled carelessly. Alwayswear protective gloves whenworking with the saw chain. ! The chain is correctly tensioned when there is no slackon the underside of the bar, but it can ...

English – 31 MAINTENANCE FIG. 56 FIG. 54 FIG. 55 Drive belt Chain sawmill with electric motor(FIG. 54) The drive belt becomes worn as the sawmill is used.The belt should be replaced after 200 hours ofoperation to avoid a belt failure during operations. Ifthe drive slips or the belt needs to be adjus...

32 – English MAINTENANCE Maintenance The maintenance described in this section refers tomeasures that can be carried out by the user. If faultsare detected that cannot be rectified in accordancewith this operator’s manual, contact your nearestauthorised service representative. Daily maintenance 1. C...

English – 33 TECHNICAL DATA Technical data Chain saw engine See information under the heading Technical datain the chain saw operator’s manual. Electric motor Power 380-420 V y-connection:Ampere:Power 220-240 V delta connection:Ampere:Electric motor feed 42 volt. Weights Saw carriage, chain saw engi...

34 – English TECHNICAL DATA Noise Levels Equivalent noise intensity at operator’s ear duringsawing, measured according to ISO 7917, dB(A) Petrol engine:Electric motor: Equivalent noise level measured according to EN1807 and ISO 7960, dB(A) Petrol engine:Electric motor: Vibration Levels Vibration lev...