Page 3 - TABLE OF CONTENT
TABLE OF CONTENT OM 0408SB1174-A 1 SPECIFICATIONS ........................................................................................................................................... 3 INTRODUCTION – TO THE PURCHASER ...............................................................................
Page 5 - SPECIFICATIONS; Features and Specifications
SPECIFICATIONS OM 0408SB1174-A 3 * With manual rotation Features and Specifications SB1174 Working Width 74" Transport Width 74" Working Height 26" Length 47 3/4" Single/Dual Auger Single Auger Diameter 15" Auger Flighting Thickness 5/16" Impeller Diameter 24" Impeller Wi...
Page 6 - INTRODUCTION; O THE; Read and understand; Illustrations
INTRODUCTION OM 0408SB1174-A 4 T O THE P URCHASER All products are designed to give safe, dependable service if they are operated and maintained according to instructions. Read and understand this manual before operation. This manual has been prepared to assist the owner and operators in the safe op...
Page 7 - SAFETY PRECAUTIONS; Read and understand this manual before operation; EFORE; Children and Bystanders; SAFETY FIRST
SAFETY PRECAUTIONS OM 0408SB1174-A 5 All products are designed to give safe, dependable service if they are operated and maintained according to instructions. Read and understand this manual before operation . It is the owner's responsibility to be certain anyone operating this product reads this ma...
Page 8 - SAFETY PRECAUTIONS - continued; OTICE; Before Operation
SAFETY PRECAUTIONS - continued OM 0408SB1174-A 6 N OTICE A safe operator is the best insurance against accidents. All operators, no matter how experienced they may be, should read this Operator's Manual and all other related manuals before attempting to operate an implement. Please read the followin...
Page 9 - Snowblower Operation
SAFETY PRECAUTIONS - continued OM 0408SB1174-A 7 Snowblower Operation 1. Before leaving the tractor/snowblower unattended, take all possible precautions. Park the tractor/snowblower on level ground, place the transmission in neutral, set the parking brake, disengage the PTO, lower the snowblower to ...
Page 10 - SAFETY PRECAUTIONS- continued
SAFETY PRECAUTIONS- continued OM 0408SB1174-A 8 22. Make sure the tractor is counterweighted as recommended by your dealer. Weights provide the necessary balance to improve stability, traction and steering. 23. Always make sure all snowblower components are properly installed and securely fastened B...
Page 11 - HE; General Information; During Operation
SAFETY PRECAUTIONS - continued OM 0408SB1174-A 9 T HE T RACTOR General Information 1. Read the operator's manual carefully before using tractor. Lack of operating knowledge can lead to accidents. 2. Do not allow anyone but the operator to ride on the tractor. There is no safe place for extra riders ...
Page 12 - AINTENANCE
SAFETY PRECAUTIONS - continued OM 0408SB1174-A 10 M AINTENANCE ALWAYS USE GENUINE PARTS WHEN REPLACEMENT PARTS ARE REQUIRED 1. Keep the tractor and snowblower properly maintained. 2. Park the tractor/snowblower on level ground, place the transmission in neutral, set the parking brake, disengage the ...
Page 13 - RANSPORTATION
SAFETY PRECAUTIONS - continued OM 0408SB1174-A 11 T RANSPORTATION 1. If the tractor/snowblower is to be driven on public roads, it must be equipped with an SMV (Slow Moving Vehicle) sign. Check local traffic codes that may apply to unit usage on public roads and highways in your area. 2. Be alert fo...
Page 14 - SAFETY DECALS; Replace immediately if damaged.
SAFETY DECALS OM 0408SB1174-A 12 Replace immediately if damaged. 5RD2500616 5RD2500813 5RD2500783 5RD2500833 5RD2500782 5RD2500827 5RD2500783 5RD2500785 5RD2500794 5RD2500795 5RD2500786 5RD2500791 5RD2500792 5RD655834 5RD2500608 5RD2500620
Page 15 - ASSEMBLY; RACTOR; NOWBLOWER; Installation of SMV Sign; Figure 2
ASSEMBLY OM 0408SB1174-A 13 T RACTOR P REPARATION See Dealer for Tractor Preparation information. S NOWBLOWER A SSEMBLY The snowblower is assembled at the factory except for the parts in the hardware bag provided with the snowblower, the chute and the options if appropriate. Use the present manual a...
Page 16 - Installation of the Chute; Figure 3
ASSEMBLY OM 0408SB1174-A 14 Installation of the Chute (Figure 3) 1. Figure 3: Place the rotation bushing (item 1) on the chute base of the snowblower. 2. Figure 3: Install the chute (item 2) over the rotation bushing and install the three 3/16" spacers (item 3) and the 3/8" spacers (item 4)....
Page 17 - Installation of Snowblower with Three Point Hitch; CAUTION; Figure 4
ASSEMBLY OM 0408SB1174-A 15 Installation of Snowblower with Three Point Hitch (Figure 4) 1. Install the two cat.1 pins (item 1) on the right and left snowblower hitches in the lower holes as shown on figure. 2. Category 1: Attach tractor lower links (item 2) to the snowblower hitch pins (item 1) and...
Page 18 - Installation of Snowblower with Quick Hitch; CATEGORY 1 only; Figure 5
ASSEMBLY OM 0408SB1174-A 16 Installation of Snowblower with Quick Hitch (Figure 5) CATEGORY 1 only 1. Install the two cat.1 pins (item 2) on the right and left snowblower hitches in the upper holes leaving 3 1/4" between the jam nut and the end of the pin as shown on figure. 2. Insert the two 2 ...
Page 19 - Installation of Manual Rotation Kit 5RDF0046
ASSEMBLY OM 0408SB1174-A 17 Installation of Manual Rotation Kit 5RDF0046 (Figures 6-7-8-9) NOTE: The rotation handle can be installed on the right or left side of the three point hitch. 1. Install the chute according to the instructions contained in the snowblower Operator's Manual, with the four 1/...
Page 20 - NOTE
ASSEMBLY OM 0408SB1174-A 18 9. Figure 8: Install plastic handle (item 5) over the rotation handle (item 6). 10. Figure 8: Insert assembled rotation tube (item 1) inside the rotation worm assembly (items 2). Align holes and insert a 10-24NC x 1’’ allen socket head capscrew (item 3) making sure the ca...
Page 21 - Installation of Hydraulic Rotation Kit 5RDF0047; To avoid serious personal injury.; Escaping
ASSEMBLY OM 0408SB1174-A 19 1. Hydraulic hose 2. Cardboard 3. Magnifying glass Installation of Hydraulic Rotation Kit 5RDF0047 (Figures 10 to 14) 1. Install the chute according to the instructions contained in the snowblower Operator's Manual. 2. Figure 10: Place the motor spacer (item 2) on the mot...
Page 23 - PROBLEM: HYDRAULIC CHUTE ROTATION IS SLOW OR DOESN'T TURN; WARNING; To avoid serious personal injury
ASSEMBLY OM 0408SB1174-A 21 PROBLEM: HYDRAULIC CHUTE ROTATION IS SLOW OR DOESN'T TURN When activating the chute rotation, it turns very slowly or not at all. WARNING To avoid serious personal injury , always wear safety glasses while doing the instructions below. SOLUTION: 1. Check if the tractor va...
Page 24 - Installation of Hydraulic Deflector Kit 5RDF048
ASSEMBLY OM 0408SB1174-A 22 Installation of Hydraulic Deflector Kit 5RDF048 (Figures 15 to 20) 1. Install the chute according to the instructions in the snowblower Operator Manual. 2. Figure 15: Remove the two manual adjustment knobs (item 1) and bolts (item 2) from each side of deflector and replac...
Page 26 - Diagram; Installation of Electric Deflector Kit 5RDF0021
ASSEMBLY OM 0408SB1174-A 24 Figure 21 Figure 21A Diagram Installation of Electric Deflector Kit 5RDF0021 (Figures 21 to 24 & Electrical Diagram) PRE-ASSEMBLY 1. Figure 21A: Install the clevis with the 1 1/32" diam. hole (item 1) on the actuator base (item 2), and the one with the 1 5/32"...
Page 29 - IMPORTANT; Danger: Tractors Too Big
ASSEMBLY OM 0408SB1174-A 27 IMPORTANT : A proper initial installation will give you years of satisfactory service on your equipment. Please read carefully following instructions that have been specially included to help you and ensure you are satisfied with your purchase. WARNING Unfortunately, snow...
Page 30 - PTS
ASSEMBLY OM 0408SB1174-A 28 Unequal Angles at Driveline Joints Avoid Equal Angles at Driveline Joints Recommended Angles at Each End of Driveline A popular habit is to change the snowblower angle in order to obtain a better scraping effect. This practice can become harmful to the driveline since the...
Page 31 - Before
ASSEMBLY OM 0408SB1174-A 29 NOTE: Before cutting, make sure the two shafts intersect by at least 7 3/4" when in working position that is when the snowblower rests on the ground. 3. Figure 26: Hold the two half-shaft side by side and locate the "L" length between the two center-to-center ...
Page 32 - Driveline Installation
ASSEMBLY OM 0408SB1174-A 30 Figure 27 Driveline Installation (Figure 27) 1. Separate the snowblower from the three point or quick hitch. 2. Remove paint from snowblower gearbox shaft (item 1) and grease driveline sliding surfaces and yoke (item 2). 3. Remove the bolts (items 3) from the driveline yo...
Page 33 - Removing Snowblower from Tractor; Three Point Hitch
ASSEMBLY OM 0408SB1174-A 31 Figure 28 Figure 29 Removing Snowblower from Tractor (Figures 28 to 31) Three Point Hitch 1. Set parking brake and turn engine off. 2. Figure 28: Remove the wire round lock pin (item 2), lower the parking stand (item 1) completely to the ground to release all pressure fro...
Page 34 - Quick Hitch
ASSEMBLY OM 0408SB1174-A 32 Figure 30 Quick Hitch 1. Set parking brake and turn engine off. 2. Figure 30: Remove the wire round lock pin (item 2), lower the parking stand (item 1) and reinsert the wire round lock pin in the lower hole (item 3). 3. Figure 31: Disconnect driveline (item 1) from tracto...
Page 35 - OPERATION; ENERAL; PERATING CONTROLS; Work and Travel Speed; DJUSTMENTS; Chain Tension Adjustment; Skid Shoe Adjustment; Clearance between cutting edge and surface:; Manual Deflector Adjustment
OPERATION OM 0408SB1174-A 33 Figure 32 G ENERAL P REPARATION 1. Read the operator’s manual carefully before using the tractor and snowblower. Be thoroughly familiar with the controls and proper use of the equipment. Know how to stop the unit and disengage the controls quickly. 2. Make sure the snowb...
Page 36 - NOW
OPERATION OM 0408SB1174-A 34 S NOW R EMOVAL M ETHODS When removing snow, do not use the snowblower as a dozer blade to push snow. Let the snowblower work its way through deep drifts. If the speed of your tractor is too fast, the snowblower may become overloaded and clog. For best results, raise the ...
Page 37 - MAINTENANCE; Shearbolts; Drive shaft; Driveline
MAINTENANCE OM 0408SB1174-A 35 M AINTENANCE Shearbolts Check the shearbolts indicated on the figure below at frequent intervals for proper tightness to be sure the blower is in safe working condition. Figure 33: To access the shear bolts, pull up the access pannel (item 1) located near the chain. If...
Page 38 - UBRICATION; DESCRIPTION
MAINTENANCE OM 0408SB1174-A 36 L UBRICATION Use oil or a grease gun and lubricate as follows: DESCRIPTION INTERVAL LUBRICATION REQUIRED Driveline 8 hours Grease each universal joint. Separate the sliding parts and cover each one of them with grease 16 hours Oil the push pins Chain 4 hours and after ...
Page 39 - RIVELINE
MAINTENANCE OM 0408SB1174-A 37 D RIVELINE T ROUBLESHOOTING AVOIDABLE DAMAGES POSSIBLE CAUSES CORRECTIVE ACTIONS Q UICK - DISCONNECT YOKE Quick-disconnect pin tight or completely seized. Quick-disconnect pin damaged (broken or bent) Quick-disconnect pin damaged in the locking portion. Quick-d...
Page 41 - AVOIDABLE DAMAGES
MAINTENANCE OM 0408SB1174-A 39 Note: Shield bearings must be greased every 8 working hours. AVOIDABLE DAMAGES POSSIBLE CAUSES CORRECTIVE ACTIONS SHIELD Excessive wear of shield bearings. Insufficient lubrication. Incorrect chain mounting. Shield interfering with implement. Follow lubricati...
Page 42 - PARTS; NTRODUCTION; ANUAL
PARTS OM 0408SB1174-A 40 I NTRODUCTION All parts are illustrated in "exploded views" which show the individual parts in their normal relationship to each other. Reference numbers are used in the illustrations. These numbers correspond to those in the "Reference Number" (REF) column, ...
Page 46 - EARBOX
PARTS OM 0408SB1174-A 44 G EARBOX 5RD663485 R EF . D ESCRIPTION Q TY P ART # 1 Casing 2 5RD659848 2 Bearing 2 5RD659844 3 Shim 1 5RD656649 4 Input shaft 1 5RD664663 5 Shim 2 5RD659855 6 Oil seal 3 5RD659852 7 Snap ring 2 5RD656652 8 Gear 2 5RD662236 9 Parallel key 2 5RD659850 10 Output shaft 1 5RD65...
Page 48 - For the Chute Installation
PARTS OM 0408SB1174-A 46 5RDF0046 - M ANUAL R OTATION R EF . D ESCRIPTION Q TY P ART # 1 Rotation handle 1 5RD667425 2 Rotation tube 1 5RD660188 3 Rotation yoke 1 5RD659595 4 Universal block 1 5RD658193 5 Rotation worm 1 5RD665953 6 Rotation worm support 1 5RD665952 7 Spring pin 1/4" x 1 1/4"...
Page 49 - YDRAULIC
PARTS OM 0408SB1174-A 47 5RDF0047 - H YDRAULIC R OTATION R EF . D ESCRIPTION Q TY P ART # 1 Hydraulic motor 50cc 1 5RD3910092 - Seal Kit 1 5RD3910093 2 Key 1/4" x 1" woodruff (incl. in 5RD3910092) 1 5RD659191 3 Motor gear 1 5RD669705 4 Flow restrictor 0.052" 2 5RD664362 5 Rubber hose 1/4...
Page 51 - LECTRIC
PARTS OM 0408SB1174-A 49 5RDF0021- E LECTRIC D EFLECTOR R EF . D ESCRIPTION Q TY P ART # 1 Actuator 1 5RD662983 2 Switchbox 1 5RD667557 3 Switch 1 5RD663383 4 Rubber cap 1 5RD658666 5 Switchbox clamp 1 5RD667558 6 Clevis – rod 1 5RD666049 7 Clevis – base 1 5RD666050 8 Pin 1" 2 5RD666057 9 Ground...
Page 52 - TORQUE SPECIFICATION TABLE
TORQUE SPECIFICATION TABLE OM 0408SB1174-A 50 GENERAL SPECIFICATION TABLE Use the following torques when special torques are not given NOTE: These values apply to fasteners as received from supplier, dry, or when lubricated with normal engine oil. They do not apply if special graphited or moly sidul...
