John Deere LPBST-35JD - Manual

Page 2 - INTRODUCTION; Introduction

Introduction - 1 INTRODUCTION Introduction Using Your Operator’s Manual Read this entire operator’s manual, especially the safety information, before operating. This manual is an important par t of your machine. Keep all manuals in a convenient location so they can be accessed easily. Use the safety...

Page 3 - ASSEMBLY; Assembly; Parts in Kit

Assembly - 2 ASSEMBLY Assembly Parts in Kit MX38959 Hardware Pack Qty. Description 1 Fan (A) 1 Hopper Assembly and Control Support (B) 1 Tube, Tow (C) 2 Clevis, Hitch (D) 2 Wheel (E) 1 Axle (F) 1 Support Frame, Hopper (G) 1 Transmission and Brace (H) Qty. Description 4 Locknut, 5/16 in. 2 Nut, 5/16 ...

Page 4 - Assemble Hopper to Frame

Assembly - 3 ASSEMBLY Assemble Hopper to Frame MX34596 1. Install six 1/4 x 1-3/4 in. hex bolts (A), and 1/4 in. thrust washer (B) through top of hopper (C) and through support frame (D), as shown. Secure bottom of bolt with 1/4 in. locknut (E). To avoid damage to plastic, do not overtighten hardwar...

Page 5 - Install Agitator and Controls

Assembly - 4 ASSEMBLY MX38962 3. Raise transmission into position by installing transmission fan shaft into center hole of the control plates on the bottom of the hopper. Lower transmission bracket (F) onto bolts (G). 4. Install axle (H) through suppor t frame assembly (I) with offset hole near cent...

Page 6 - INSTALLING; Installing; Installing the Spreader

Installing - 5 INSTALLING MX39207 2. Install 3/8 in. ID O-ring (E) on transmission shaft (F) until seated on bottom of hopper (G). 3. Install agitator (H), and secure with 1/8 x 1 in. cotter pin (I) through top loop in agitator and hole in transmission shaft, as shown. MX39208 4. Make sure transmiss...

Page 7 - REMOVING; Removing; Removing the Spreader; Operating; Daily Operating Checklist

Removing - 6 REMOVING Removing Removing the Spreader 1. Park machine safely. See “Parking Safely” in the Safety section. 2. Remove all materials from the hopper before removing spreader from machine. 3. Remove 1/8 in. spring locking pin from hitch pin. 4. Hold spreader tow tube to remove pressure fr...

Page 8 - SERVICE; Operational Tips; Service; Maintenance Tips; Annual Maintenance

Service - 7 SERVICE Operational Tips • Always operate your spreader with the speed limit for which it was designed - 3 mph. • When backing, carefully back straight to avoid jack knifing, which could result in damage to equipment. • Only tow your spreader behind vehicles for which it was designed - r...

Page 9 - TROUBLESHOOTING; Calibration; Troubleshooting; Using Troubleshooting Chart

Troubleshooting - 8 TROUBLESHOOTING MX39213 8. Remove three screws (P) that secures control plate assembly (Q). 9. Remove 1/4 x 2-1/2 in. bolt (R), 1/4 in. flat washer (S), 1/4 in. lockwasher (T), and 1/4 in. nut (U) and flow control assembly (V) from support tube (J). MX34611 10. Separate parts as ...

Page 10 - SPECIFICATIONS; Specifications; LPBST-35JD Broadcast Spreader

Specifications - 9 SPECIFICATIONS Specifications LPBST-35JD Broadcast Spreader Dimensions Size (maximum weight). . . . . . . . . . . . . . . . . . . . . . . . . . . 79 kg (175 lb) Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.10 cu m (3.5 cu ft) Wheels and Tires . . . ...

Page 12 - Getting Quality Service - 11; GETTING QUALITY SERVICE; Calibration Settings; Getting Quality Service; John Deere Quality Continues with Quality Service

Getting Quality Service - 11 GETTING QUALITY SERVICE Calibration Settings If the product you are using is not listed in the flow control setting table, use the this calibration guide to set the flow control. Calibration guide information is also provided on the hopper decal of the spreader. Using ap...

John Deere LPBST-35JD - Manual

Table of Contents:

Summary

Other John Deere Models