JL Audio SB-SMRT-4-2/8W3v3 - Manual
JL Audio SB-SMRT-4-2/8W3v3 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Continued on Next Page; D E T A I L
- Page 3 – do not tIGHten tHIs assemBlY Yet!; C o n G R a t u l a t I o n s !; You have completed the installation for this model!; steP 8; into the Stealthbox® as shown.; noW You need to tIGHten all oF tHe PReVIouslY; Re-install the woofer into the enclosure.
- Page 4 – I n C l u d e d H a R d W a R e; /4” Split Lock Washer; s P e C I F I C a t I o n s; Ohms; P o W e R R e C o m m e n d a t I o n; Fits JL Audio Models:; To change the OEM front speakers requires extensive
I n s t a l l a t I o n G u I d e
for the
SB-SMRT-4-2/8W3v3
sKu#94448
2008+
Thank you for choosing a JL Audio Stealthbox
®
for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox
®
installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. If you prefer to perform your own installation,
please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox
®
be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
s t e P 1
Read all of the instructions through once before starting the
work.
We know you’ve seen this warning before but, if
you only follow each step as it comes, the progression
won’t make sense, if you read everything all the way
through, you’ll understand, the job will be easier.
Clean out the passengers side of the vehicle so that you have
a comfortable place to work.
Continued on Next Page
s t e P 2
Remove the carpeting and, the foam underlayment as if
you were accessing the battery (refer to the vehicles owners
manual if neccessary).
s t e P 3
Under the passengers end of the dash there is a Torx screw
that holds the dash end trim panel in place, remove it and,
the trim piece.
SB-SMRT-4-2/8W3V3 INSTR_SKU# 011288
InstallatIon
d I F F I C u l t Y :
4
5
o u t
o F
estImated tIme:
3 HouRs
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Continued on Next Page SB-SMRT-4-2/8W3V3 INSTR_SKU# 011288 s t e P 7 On the Bottom end of the 1/4-20 All Threaded Rod, install the Bottom Bracket as shown (approximately 1- 1 1/4” from the bottom), using included 1/4-20 Nuts, Washers and, Split Lock Washer. do not tIGHten tHIs assemBlY Yet! s t e P ...
Continued on Next Page SB-SMRT-4-2/8W3V3 INSTR_SKU# 011288 s t e P 1 4 Rotate the Bottom Bracket on the 1/4-20 All Threaded Rod so that it lines up with the threaded insert in the Stealthbox®, you may need to raise or lower the position of the Bottom Bracket on the All Threaded Rod in order to align...
SB-SMRT-4-2/8W3V3 INSTR_SKU# 011288 Page 5• JL Audio, Inc 2009 All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of J...
