Jet M-628900 - Manual - manualsarea.com

Page 3 - Table of Contents; Using the TUF Tool

3 Table of Contents Warranty & Service.................................................................................................................................... 2 More Information .............................................................................................................

Page 4 - OFF; Warnings

4 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or rem...

Page 5 - ADDITIONAL INFORMATION

5 29. Stand to one side of the conveyor and make sure no one else is standing in line with the conveyor while feeding into the machine. The drum sander operates at high speed and should a part slip, it will exit the machine at a high rate of speed and may result in injuries to anyone standing direct...

Page 7 - Grounding Instructions; This adapter is not applicable in Canada.; Recommended

7 Grounding Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric co...

Page 8 - Performax 10-20 Accessories; Description

8 Contents of the Shipping Carton 1. Sander Assembly 1. Handwheel with Handle 1. TUF Tool 1. Abrasive Strip (wrapped on the drum) 1. Conveyor Belt (attached to the base) 1. Owner's Manual 1. Warranty Card 1. Hardware Bag (for attaching the Sander to the Optional Open Stand) — containing: 4. 3/8”-16x...

Page 9 - Switch Lock; Turn the switch to the off position and; Circuit Breaker; B C

9 On/Off Switch Before powering up the unit, make sure all of the tools used to assemble and adjust the unit are removed and accounted for. Make sure your hands, loose clothing and any other items that may get caught are safely away from the unit. The On/Off Switch (Figure 2, Item A) is located on t...

Page 10 - This Page Intentionally Left Blank

Page 11 - Conveyor Belt Tracking; Adjustment should be made in 1/4 turns of; Conveyor Belt Tension

11 Conveyor Belt Tracking Belt tracking adjustment may be necessary during the break-in period and normal operation to compensate for belt stretching. Abrasive belt tension must be properly adjusted before adjusting the tracking. Adjust the belt tracking while the conveyor belt is running at its fas...

Page 12 - tighten the two hex cap bolts.; Fine Tuning Drum Alignment

12 Checking Drum Alignment The sanding drum comes preset from the factory. If a problem with the drum alignment occurs, follow the instructions listed below. 1. Lift the knob (Figure 6, Item A) to open the dust cover and remove the abrasive strip. If you are unsure how to do this, see the “Wrapping ...

Page 13 - Wrapping Abrasive Strips

13 Wrapping Abrasive Strips Note: When using Performax “Ready to Wrap” and “Ready to Cut” abrasives, not all of the steps below are necessary. You can use the original abrasive belt that came with the sander as a template for cutting your own strips. 1. Mark and cut a taper at one end of the roll, a...

Page 14 - Clip the sandpaper into the outboard

14 Using the TUF Tool TM The Tuf Tool (Figure 13) can also be used to hold the take-up fastener in place while you feed the sandpaper through the slot. 1. Clip the sandpaper into the outboard fastener. Wrap the drum, being careful not to overlap the windings. Hold the sandpaper over the inboard slot...

Page 16 - Abrasives; Selecting Drum Abrasives; Grits that are too fine can; Stretching Abrasive Life; Grit

16 Abrasives The abrasive material you choose will have a substantial effect on the performance of your sander. Variations in paper type, weight, coating and durability all contribute to achieving your desired finish. For the best sanding results, Performax offers premium abrasives that have been te...

Page 19 - Troubleshooting Guide; Problem

19 Troubleshooting Guide Problem Possible Cause Solution Conveyor belt does not move. Shaft coupler is not attached. Attach the shaft coupler. Conveyor rollers run intermittently. Shaft coupling is loose. Align the shaft flats of the gear motor and the drive roller and tighten the shaft-coupling set...

Page 20 - Exploded View – 10-20 PLUS Sander

Page 21 - Parts List for the 10-20 PLUS Sander

21 Parts List for the 10-20 PLUS Sander Item No. Part No. Description Size Qty 1 1020-101 Handwheel, Height Adjustment 1 2 1020-102 Socket Head Button Screw 5/16-18UNCx3/4 2 3 TS-0680031 Flat Washer 5/16 8 4 1020-104 Main Support 1 5 1020-105 Lock Nut 1/2-20UNF 1 6 TS-0680061 Flat Washer 1/2 1 7 102...

Page 23 - Wiring Diagram

Page 24 - WMH Tool Group

24 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com.