Jet JWSS-10CS - Manual

5 Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscur...

7 The most common accidents among table saw users, according to statistics, can be linked to kickback, the high-speed expulsion of material from the table that can strike the operator. Kickback can also result in operator’s hands being pulled into the blade. Kickback Prevention Tips to avoid the mos...

8 Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury Contents of the Shipping Containers 1 Table saw 1 Right Wing Extension 1 Splitter Guard Assembly 1 Accessory Package 1 Owner’s Manual 1 Warranty Card Accessory...

9 Left Wing Extension Box (optional accessory) 1 Left Wing Extension w/Miter Slot 1 Miter Gauge 1 Miter Gauge Bar 1 Miter Gauge Handle 1 Miter Gauge Fence Hardware Bag 4 Socket Head Cap Screws M10x90 4 Lock Washers M10 4 Flat Washers M10 1 Hex Wrench 8mm XACTA Fence II Homeshop 30/52 Box One: 1 XACT...

10 Assembly Unpacking and Clean-Up Do not connect the table saw to the power source until assembly has been completed! Failure to comply may cause serious injury! • Tool: 12mm Wrench 1. Remove all contents from the shipping container. Do not discard any shipping material until the saw is set up and ...

12 Miter Gauge for Left Extension Wing Hardware: Miter Gauge Tools: Cross Point Screw Driver, Square 1. Change the angle on the miter gauge by loosening handle (E, Fig. 7) and turning the fence (F, Fig. 7) to desired angle. To move gauge beyond index stops of 45 ° and 90 ° , flip back the stop (G, F...

14 Sliding Table Miter Gauge Hardware: Miter Gauge, Fence, (2) Handles, Stop, Fence Bar, Indicator Bar, Bushing, Bracket Clamp Assembly & (2) Handles Tools: 2.5mm Hex Wrench 1. Slide the miter gauge fence (B, Fig. 13) into the bar (A, Fig. 13) and attach to the miter gauge body (C, Fig. 13) with...

15 Mounting the Switch Assembly Hardware: (2) 1/4x1/2 Hex Cap Screws, (2) 1/4 Lock Washers, (2) 1/4 Flat Washers. Tool: 4mm Hex Wrench Referring to Figure 15: Mount the switch assembly (A) to the bottom side of the front rail (B) with two button head cap screws (C) and two washers (D). Note: The swi...

16 table, until it is level with the saw table (Figure 17). As one part of the edge becomes level with the table, tighten the clamp on that side. Then move to the other side and repeat, until the full length of the edge is level with the saw table. Lay a straight edge across both extension table and...

17 slot (A. Fig. 21), orient the guide tube (B) with respect to the rail (C) as shown in Figure 21. If your left table wing is the sliding table type (D, Fig. 22), mount the guide tube (F) so it lines up with the left edge on the angle iron portion of the rail (E). Referring to Figure 23: 1. Align t...

18 4. Raise or lower two nylon adjustment screws (A, Fig. 27) the same number of turns until the space between the bottom of the fence and the table is the same. Care must be taken to raise or lower the fence on each side equally or the fence may not be 90 ° to the table after the height adjustment ...

19 Installing the Blade When installing or changing saw blade, always disconnect saw from power source! Failure to comply may cause serious injury! Hardware: Blade Tools: Arbor Wrench, Scrap Piece of Wood 1. Raise the blade arbor and make sure the arbor is at the zero degree position. 2. Remove the ...

21 Hooks for Miter Gauge and Fence Hardware: (2) Miter Gauge Hooks, (2) Fence Hooks, (4) M8x16 Carriage Bolts, (4) M8 Flat Washers, (4) M8 Lock Washers & (4) Hex Nuts Tool: 13mm Wrench 1. Mount the two fence hooks (A, Fig. 38) with two M8x16 carriage bolts, two M8 flat washers, two M8 lock washe...

22 Grounding Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric c...

23 Adjustments Blade Alignment Tools: 8mm Hex Wrench, Combination Square & Marker Blade alignment with the miter slot is adjusted at the factory. After a period of use, or after moving the saw to another location, the blade may no longer be aligned properly. To check and align the blade, see Fig...

24 Adjusting 45 ° and 90 ° Positive Stops The stops have been adjusted at the factory. After a period of use, or, after moving the saw to another location, the stops may no longer be set properly. To check and adjust the stops: Tool: 12mm Wrench, Combination Square 1. Disconnect saw from power sourc...

27 Maintenance General Maintenance Cabinet and Motor: Keep the inside of the cabinet clear of sawdust and wood chips. Vacuum out the inside of the cabinet and blow out the inside with an air hose. Make sure the motor fan and fan cover are also kept clear of sawdust. Worm Shafts and Trunnions: Use a ...

28 Troubleshooting Trouble Possible Cause Solution Saw stops or will not start 1. Overload tripped 2. Saw unplugged from wall or motor 3. Fuse blown or circuit breaker tripped 4. Cord damaged 5. Starting Capacitor is bad 6. Centrifugal Switch bad or out of adjustment 1. Allow motor to cool and push ...

29 Parts XACTA Fence II Homeshop 30/52 Fence Assembly Index No. Part No. Description Size Qty 1 ............... HF2-101 ................... Left Side Plate...................................................... .................................... 1 2 ............... HF2-102 ................... Fence...

30 Cabinet Assembly Index No. Part No. Description Size Qty 1 ............... JWSS10CS-01 ......... Cabinet ................................................................. .................................... 1 2 ............... JWSS10CS-02 ......... Door .............................................

31 Guard Assembly Index No. Part No. Description Size Qty 1 ............... 200321 ..................... Support Arm ......................................................... .................................... 1 2 ............... TS-2342061 ............. Nylon Lock Nut................................

32 Table Assembly Index No. Part No. Description Size Qty 1 ............... TS-1550061 ............. Flat Washer .......................................................... M8 ............................. 13 2 ............... TS-1551061 ............. Lock Washer ........................................

35 Sliding Table Assembly Index No. Part No. Description Size Qty 1 ............... 200364 ..................... Sliding Table ........................................................ .................................... 1 2 ............... 200411 ..................... Wiper Bracket w/Wiper ...........

38 Rail Assembly Index No. Part No. Description Size Qty ................. 708783Z ................... Rail Assembly - Standard (30”) ........................... .................................... 1 ................. 708782Z ................... Rail Assembly - Long Table (52”) .......................

40 Motor & Trunnion Parts List Index No. Part No. Description Size Qty 1 ............... 200310 ..................... Rear Trunnion Bracket ......................................... .................................... 1 2 ............... TS-1550061 ............. Flat Washer .......................

44 230V Wiring WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.com