Jet 708358 - Manual - manualsarea.com

Page 3 - Warnings

3 1. Read and understand the entire owner ’s manual before attempting assembly or operation. 2. This wood lathe is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a wood lathe, do not use it until the pro...

Page 4 - SPEED RECOMMENDATIONS; to avoid heat build up.

4 SPEED RECOMMENDATIONS Diameter of Work Roughing RPM General Cutting RPM Finishing RPM Under 2" 1500 3000 3000 2 to 4" 600 1500 2300 4 to 6" 450 1100 1500 6 to 8" 450 600 1100 8 to 10" 450 600 850 10 to 12" 450 600 850 12 to 14" 450 450 600 26. When sanding, remove the t...

Page 5 - Grounding Instructions; Volts; Recommended

5 Grounding Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric co...

Page 6 - Disconnect the machine from the power source.

230 Volt Operation If 230V, single-phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This lathe is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads f...

Page 9 - WARNING; Read and understand the entire contents of; Contents of the Shipping Containers; Contents of Accessory Package

9 WARNING Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury! Contents of the Shipping Containers 1. Lathe 1. Tailstock 1. Headstock 1. Face Plate 1. Tool Rest Body 1. Accessory Package 1. Owner’s Manual and Warr...

Page 10 - Stand Shelf

10 Stand Legs (optional accessory) 1. At this point the headstock, tailstock and tool rest should be removed. With help from another person, lift the lathe bed and place onto a workbench. 2. Angle lathe bed so that stand leg mounting holes are accessible, see Figure 2. 3. Thread adjustable feet (A, ...

Page 11 - Push in pin to keep the spindle from turning.; Never press the headstock spindle lock while

11 G. Headstock Spindle Lock: (G, Fig. 5) Push in pin to keep the spindle from turning. CAUTION! Never press the headstock spindle lock while the spindle is turning! H. Headstock On/Off Switch: (H, Fig.5) Flip the switch up to turn “ON” the lathe. Flip the switch down to turn the lathe “OFF”. I. Hea...

Page 12 - Lathe Tools

12 N. Tool Rest Body Lock Handle: (N, Fig. 8) Locks the tool rest body in position. Unlock handle to position the tool rest in any location along lathe bed. Tighten handle when properly positioned. O. Tool Rest Lock Handle: (O, Fig. 8) Locks the tool rest in position. Unlock the handle to position t...

Page 13 - Mounting Workpiece Between Centers; Mov e tool rest into position. It should be; lowest speed and bring it up to

13 Lathe Tools (continued) Skew — used to make vees, beads, etc., see Figure 11. Square Scraper — used for diameter scraping and featureless scraping, etc, see Figure 11. Large Domed Scraper — used to reduce ridges on the interior of bowls, round edges of bowls, etc, see Figure 11. Parting Tool — us...

Page 15 - of the desired width of your cut.; Parting

15 Beads 1. Place the parting tool on the tool rest and move the tool forward to make the full bev el of the tool contact the workpiece. Gently raise handle to make cut to the appropriate depth. 2. Repeat for other side of the bead. 3. Using a small skew or spindle gouge, start in the center between...

Page 16 - hav e good flat surfaces.

16 Sanding and Finishing Leav ing clean cuts will reduce the amount of sanding required. Begin with a fine sandpaper (120 grit or finer). Coarser sandpaper will leave deep scratches that are difficult to remove, and dull crisp details. Fold the sandpaper into a pad; do not wrap sandpaper around your...

Page 18 - To Shape the Outside of a Bowl; workpiece with a wood mallet.

18 To Shape the Outside of a Bowl 1. Odd shaped burls, crotches and other irregular shaped blanks require special preparation before mounting in a chuck, or onto a faceplate. Remove the bark, if there is any, from what appears to be the center of the top of workpiece. 2. Drive the spur center into t...

Page 19 - Stop the lathe and move the tailstock away.; Sanding and Finishing a Bowl

19 To Shape the Interior of a Bowl 1. Stop the lathe and move the tailstock away. Remove the center from the tailstock to prev ent bumping it with your elbow. 2. Adjust the tool support in front of the bowl just below the centerline, at a right angle to the lathe bed. 3. Rotate the workpiece by hand...

Page 21 - Troubleshooting; Problem Possible

21 Troubleshooting Problem Possible Cause Solution Excessiv e Vibration. 1. Workpiece warped, out of round, has major flaw, improperly prepared for turning, or RPM is set too high 2. Worn spindle bearings 3. Worn belt 4. Motor mount bolts loose 5. Lathe on unev en surface 1. Correct problem by plani...

Page 22 - Bed Assembly

Page 23 - Description

23 Bed Assembly Index Part No. No. Description Size Qty. 1 .......... JWL1442-201............... Bed........................................................ ............................................... 1 2 .......... JWL1442-202............... Stud....................................................

Page 24 - Headstock Assembly

Page 27 - Stand Assembly

27 Stand Assembly (optional accessory) Stand Assembly Index Part No. No. Description Size Qty. 3 .......... JWL1642-203............... Stand..................................................... ............................................... 2 5 .......... JWL1642-205............... JET Stripe.........

Page 28 - Safety Guard

28 JWL-1442VS Safety Guard (optional accessory) Safety Guard 1. Mount the guard bracket (A) to the headstock with two 3/8” flat washers, two 3/8” lock washers and two 3/8”-16 x 1-1/2” socket head cap screws (B). 2. Attach the guard (C) to the guard bracket by inserting the rod and lifting up on the ...

Page 29 - Index Part

29 Safety Guard Assembly Safety Guard Assembly Index Part No. No. Description Size Qty. 1 .......... JWL1442-301............... Guard Bracket ....................................... ............................................... 1 2 .......... TS-0270011 ................. Set Screw ...................

Page 31 - Wiring Diagram

Page 32 - WMH Tool Group

32 WMH Tool Group 2420 Vantage Drive Elgin, IL 60123 Phone: 800-274-6848 www.wmhtoolgroup.com