JENSEN JKRS3 - Manual

JENSEN JKRS3

JENSEN JKRS3 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
Page: / 16

Table of Contents:

  • Page 2 – INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH
  • Page 3 – Starter Output
  • Page 4 – Accessory Output
  • Page 5 – WIRING CONNECTIONS: 12 Pin Input / Output Harness; Black Wire: Chassis Ground Source; Control Switch; GRAY WIRE: Negative Inhibit Input 1
  • Page 6 – Brake Switch Positive Shutdown Detail; LIGHT BLUE Wire: Ignition 3 / Shock Disable Output; Switch
  • Page 7 – General Motors VATS By-Pass Diagram
  • Page 8 – Tachometer Input Wiring Detail; Green/Yellow Wire: Diesel Wait To Start Input
  • Page 9 – Wire Ground Switched Door Lock Circuits:; Wire Ground Switched Door Lock/Unlock Wiring Detail; Wire Positive Switched Door Locks:; Wire Positive Switched Door Lock/Unlock Wiring Detail
  • Page 11 – Flash; HOOD PIN SAFETY SHUT DOWN:
  • Page 13 – KEY IN SENSOR CIRCUITS:
  • Page 14 – METHOD 1; METHOD 2
  • Page 15 – COMPLETING THE INSTALLATION:; point these out to the customer.
Loading the manual

128-7052

1 of 16

Kit Contents

(1) Control Module

(1) 3 Button High Frequency Transmitters

(1) 5 Button Two Way LED Based Transceiver

(1) On Glass Mount Superheterodyne Transceiver

(1) Multi Pin Input/Output Harness

(1) Six Pin Power Harness

(1) Diesel Wait To Start Input

(1) Auxiliary 4 Pin Output Harness

(1) 2 Pin Door Lock Harness

(2) 30 Amp In-line Fuse Holders With Fuses

(1) Control Switch

(1) Plug In Push-Button Programming Switch

(1) Ring Terminal

(4) 1/2" Long Screws

(1) Pin Switch

(1) Remote Start Warning Label

(1) Literature Package

Model JKRS3

Installation Manual

3 Channel Remote Start / Keyless Entry System

Installation Instructions

This Unit Is Intended For Installation In Vehicles With

12 Volt Negative Ground Electrical Systems,

Gasoline or Diesel With True Tach Reference

And Automatic Transmissions Only.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH

128-7052 2 of 16 This Remote Start/Keyless Entry System is designed for use with Automatic Transmission Vehicles Only! Theunit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire isnot connected, then the unit will remain in the Gasoline m...

Page 3 - Starter Output

128-7052 3 of 16 3 THE TRANSCEIVER/ANTENNA ASSEMBLY: The Superheterodyne Transceiver Antenna Assembly provided with this unit allows routing from below the dash-board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for bestreception. Special consideratio...

Page 4 - Accessory Output

128-7052 4 of 16 Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury andproperty damage.SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. T...

Other JENSEN Models

All JENSEN Other