JENSEN JKRS3 - Manuals - manualsarea.com

Page 2 - INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH

128-7052 2 of 16 This Remote Start/Keyless Entry System is designed for use with Automatic Transmission Vehicles Only! Theunit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire isnot connected, then the unit will remain in the Gasoline m...

Page 3 - Starter Output

128-7052 3 of 16 3 THE TRANSCEIVER/ANTENNA ASSEMBLY: The Superheterodyne Transceiver Antenna Assembly provided with this unit allows routing from below the dash-board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for bestreception. Special consideratio...

Page 4 - Accessory Output

128-7052 4 of 16 Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury andproperty damage.SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. T...

Page 5 - WIRING CONNECTIONS: 12 Pin Input / Output Harness; Black Wire: Chassis Ground Source; Control Switch; GRAY WIRE: Negative Inhibit Input 1

128-7052 5 of 16 WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain toremove any paint or grease and secure this wire with a self-tapping screw and ring ...

Page 6 - Brake Switch Positive Shutdown Detail; LIGHT BLUE Wire: Ignition 3 / Shock Disable Output; Switch

128-7052 6 of 16 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected toin the vehicle.This wire provides a + 12 Volt output when the ignition k...

Page 7 - General Motors VATS By-Pass Diagram

128-7052 7 of 16 7 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activationperiod, then vibration from the running vehicle can cause the alarm to trigger. In this case, connect the Light BlueWire to terminal #86 of a externa...

Page 8 - Tachometer Input Wiring Detail; Green/Yellow Wire: Diesel Wait To Start Input

128-7052 8 of 16 Green/Orange Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. Thiswire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect tothe negative...

Page 9 - Wire Ground Switched Door Lock Circuits:; Wire Ground Switched Door Lock/Unlock Wiring Detail; Wire Positive Switched Door Locks:; Wire Positive Switched Door Lock/Unlock Wiring Detail

128-7052 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Door Lock/Unlock Harness: (White Connector) The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to ...

Page 11 - Flash; HOOD PIN SAFETY SHUT DOWN:

128-7052 11 of 16 11 c. Immediately turn the ignition key OFF.d. Hold the program switch ON, then start the vehicle using the ignition key.e. When the unit senses the tach signal, the parking lights will begin to flash.6. Release the program switch. The parking lights will turn on for 3 seconds to i...

Page 13 - KEY IN SENSOR CIRCUITS:

128-7052 13 of 16 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing aremote start device. Often when the ignition switch is turned off while the gear selector is in any po...

Page 14 - METHOD 1; METHOD 2

128-7052 14 of 16 14 such as the light on reminder.These situations should be carefully considered before altering the vehicle's wiring and must be fully explained to theconsumer.Circuits may be used only if the above circuit is not available.To connect to the key in sensor as shown in method 1: 1.L...

Page 15 - COMPLETING THE INSTALLATION:; point these out to the customer.

128-7052 15 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must beconnected to the Gray/Black wire of the Remote Start Unit. Th...