Jasco ZWAVEKIT Manual - Free PDF Download

Page 2 - Introduction; Thank you for your purchase of a GE Z-Wave

Introduction : Thank you for your purchase of a GE Z-Wave ® enabled control device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product family includes a variety of devices to control lighting in ...

Page 3 - There are no user serviceable; Dimmer switch; CAUTION; LED light

The auxiliary switch is not Z-Wave enabled and does not directly control electrical loads. It must be used with a compatible Z-Wave enabled, 3-wire switch in three-way installations where a light is controlled from 2 locations such as the top and bottom of a staircase. This switch communicates with ...

Page 4 - WARNING; Controlling Appliances:

RISK OF FIRERISK OF ELECTRICAL SHOCKRISK OF BURNS WARNING Controlling Appliances: Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance, also an unintentional activation may occur if the wrong...

Page 5 - - Brick, tile or concrete walls block more of the RF signal than

Wireless Range This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 65 feet . Actual performance in a home depends on the number of walls between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled ...

Page 6 - The distances shown in the table below are typical; Type of Construction; Number

Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices . Note: The distances shown in the table below are typical examples. Actual performance in your home will vary. From the Remote (or repeating Z-Wave module) to destination device: * For Plug-in Modules or In-Wall Devices I...

Page 7 - IMPORTANT NOTE ABOUT 3-WAY CIRCUITS

Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth® and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wav...

Page 10 - Wiring Digram

500W Blue Yellow Yellow White Ground (Green) Green Neutral (White) Auxiliary Switch Dimmer Switch Black Green Black Hot (Black) Yellow Black Green Hot (Black) Two Auxiliary Switches for 4-way installation. 45610 Auxiliary Switch One Auxiliary Switch for 3-way installation. Up to 2 Auxiliary switches...

Page 11 - Single, Dual and Triple Gang Boxes; Dimmer Rating Number of Dimmers

500W Blue Yellow Yellow White Ground (Green) Green Neutral (White) Auxiliary Switch Dimmer Switch Black Green Black Hot (Black) Yellow Black Green Hot (Black) Two Auxiliary Switches for 4-way installation. 45610 Auxiliary Switch One Auxiliary Switch for 3-way installation. Up to 2 Auxiliary switches...

Page 14 - Observe Important Wiring Information; Always follow the recommended wire strip lengths and wiring

SHOCK HAZARD! Turn OFF the power to the branch circuit at the circuit breaker in your electrical service panel. Ensure power is OFF before you install this device. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch. WARNING Shut off power to t...

Page 15 - Wire Connector / Combination Chart

Instructions: Strip insulation 3/8” for 12 or 14 AWG wire. Strip insulation 7/16” for 16 or 18 AWG wire.Hold stripped ends together in parallel and align any frayed strands (do not twist wires).Push wires firmly into connector. Twist connector clockwise with fingers until tight. Pull wires to check ...

Page 16 - Remote Control; Manual Control

Key Features - Controls one light from two locations- Remote On/Off/Brightness control via the Z-Wave controller/ network - Manual On/Off/Brightness control with the front panel rocker- LED indicates primary switch location in a dark room- Adjustable Dim rates BASIC OPERATION Remote Control GE Z-Wav...

Page 19 - When Receiving a Z-Wave Dim Command

- Parameter No: 3- Length: 1 Byte- Valid Values = 0 or 1 (default 0) Invert Switch If the dimmer switch is accidentally installed upside down with “On” at the bottom and “Off” at the top, the default On/Off rocker settings can be reversed by changing parameter 4’s value to “1”.- Parameter No: 4- Len...

Page 20 - When Receiving an All-On or All-Off Command

- Valid Values:Parameter 7 (default = 1) Valid Values: 1-99Parameter 8 (default = 3) Valid Values: 1-255 2 . Manual Control Dimming (pressing the Dimmer’s rocker) - Parameter 9 (number of steps or levels)- Parameter 10 (timing of the steps)- Length: 1 Byte- Valid Values:Parameter 9 (default = 1) Val...

Page 22 - FCC; Statement includes the following paragraph:; that to which the receiver is connected; Operation is subject to the following two conditions:; that may cause undesired operation of the device.; To comply with the FCC RF exposure compliance; Compliance with IC Rules and Regulations

FCC U2Z45606-7 The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reas...

Page 23 - This Class B digital device complies with Canadian ICES-003.; SPECIFICATIONS; product improvement

This Class B digital device complies with Canadian ICES-003. SPECIFICATIONS Power: 120 VAC, 60 Hz. Signal (Frequency): 908.42 MHz. Minimum Load: 40W, incandescent lamps only. Maximum Load: 500W, incandescent lamps only. Range: Up to 65 feet line of sight between the Wireless Controller and the close...