Jackson Automobile Battery Charger - Manual
Jackson Automobile Battery Charger – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Supercharger Installation Instructions
- Page 4 – The
- Page 5 – MAKE SURE THAT THE; VERY IMPORTANT; : Check the clearance
- Page 6 – NON POWER STEERING CARS:; Locate; Illustration 4.1 con’t
- Page 8 – SUPERCHARGER PREPARATION
- Page 9 – SUPERCHARGER INSTALLATION; (this may require some; Make very certain that all throttle cable-
- Page 10 – AIRFLOW METER WORK
- Page 11 – See; The hose is supplied a bit longer than it; IMPORTANT! Secure the air bag harness
- Page 14 – ENGINE ADJUSTMENTS; The best tool to
- Page 15 – You can order a Jackson Racing
- Page 16 – ing from the supercharger at idle. This is normal.; LONG TERM MAINTENANCE; As the belt wears, small; TROUBLESHOOTING; You might want to add a Jackson Racing Boost
READ THESE INSTRUCTIONS THOROUGHLY!
Follow the instructions STEP-BY-STEP, and your
installation will be trouble free. If in doubt,
CALL
1-888-888-4079
. We suggest that as you pro-
ceed through the installation, you should read a
few steps ahead in the instructions so you are
certain to catch all notes and warnings.
ATTENTION SUPERCHARGER INSTALLER!
Before proceeding with the installation, it is
important to know that to validate the 2 year,
100K warranty on your new J/R supercharger,
you must completely fill out the Moss Motors /
Jackson Racing warranty card that comes in
every kit, including serial number which is on a
small white ‘bar code’ label on the body of the
supercharger. Write down all of the numbers
which appear on that label in the appropriate
space on the warranty card. Be certain to do this
now because once your supercharger is
installed, it may be almost impossible to retrieve
that serial number.
SPECIAL NOTE
: Jackson Racing Supercharger
Systems are designed to be installed by individu-
als with good mechanical sense and with the
proper tools. Use your discretion--if you are not a
competent mechanic, do not attempt this installa-
tion.
TOOLS REQUIRED:
Most of these tools are
available at your local hardware or auto parts
stores.
17mm, 14mm, 13mm, 12mm, 10mm & 8mm
sockets
Deep sockets (14mm or 9/16”, 10mm)
Phillips and Standard screwdriver
Multi-purpose pliers
10mm, 12mm, and 17mm open end wrench
Timing light
A shop manual is useful.
WARNING:
Once the installation is complete,
CHECK AND RECHECK ALL fuel system con-
nections for possible leaks before operating the
vehicle. 91-octane gasoline (or higher) is
required when running a supercharger.
During this installation process, you will reuse
some parts or hardware and not reinstall others.
It is recommended that you make space for
those that you will reuse, and a separate space
for those that you will not reinstall. In addition,
you should save the parts that will not get reused
in case you ever have reason to convert the
engine back to stock.
Enclosed is a set of labels that we suggest you
use to label the electrical connectors that you will
be unplugging.
Installation Instructions
SUPERCHARGER
with PowerCard
‘
90-’93 Mazda Miata
Part# 999-156, 999-157, 999-158, 999-159
440 Rutherford St. P.O. Box 847 Goleta, CA 93117
1-888-888-4079 • FAX 805-692-2523 • www.supercharger.com
999-156
-1-
Revised 1/07
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
1.0 DISASSEMBLY 1.1 With the engine running, raise the hood andlocate the main under hood fuse box by the fend-er well near the firewall on the passenger side ofthe engine compartment. Lift the main fuse boxcover and locate the relay labeled “FUEL INJ”.While the engine is running, remove the “FUELIN...
3.0 BELT DRIVES 3.1 NOTE: CARS WITH POWER STEERING: You will be rearranging your power steeringbracket components per figure 3.2. Referring tofigure 3.1, remove the slot bracket and pillowblock by removing bolts “A”, “C”, and “D”. Takethe flat idler pulley bracket from your kit and trialfit it to th...
3.3 Secure the idler pulleys firmly to the flat brack-et. Proceed to install the idler pulley assemblyonto the car per the procedure practiced duringthe trial fitting. The final assembly (minus the pul-leys) should look like figure 3.3. VERY IMPORTANT: MAKE SURE THAT THE DRIVER’S SIDE IDLER PULLEY I...
