Intellinet Network Solutions 503679 - Manual

Page 3 - intrOductiOn; Thank you for purchasing the INTellINeT NeTWoRK SolUTIoNS; Package Contents

intrOductiOn Thank you for purchasing the INTellINeT NeTWoRK SolUTIoNS ™ Wireless Super G outdoor Poe Access Point and Bridge, Model 503679.This professional Wireless G access point and bridge delivers a wide assortment of features that appeal to wireless users requiring a durable, flexible and powe...

Page 4 - tABle Of cOntents; section

tABle Of cOntents HARdWARe/CoNNeCTIoNS ........................................................................6BASIC IP NeTWoRKING ................................................................................7 CONFIGURATION ...........................................................................

Page 5 - regulatory statements; • Consult the dealer or an experienced radio/TV technician for help.; FCC Caution

regulatory statements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential in...

Page 6 - not

6 HARDWARE/CONNECTIONS Model 503679 External Antenna Surge Protector HArdWAre/cOnnectiOns The components, connections and indicators depicted in the image (and directly corresponding to the unit itself) are detailed below as they appear from left to right. In addition, there are four holes on the re...

Page 7 - BAsic ip netWOrkinG; Ports; software from using the connection.; Static IP Address; Static addressing is commonly used for your servers.; Dynamic IP Address; simplify the network management.; DHCP (Dynamic Host Configuration Protocol); involves a few additional parameters that need to be configured:

BAsic ip netWOrkinG IP (Internet Protocol) IP stands for Internet protocol. In an IP network, every device has a unique IP address (e.g., 192.168.10.35) to identify itself. There are two ways of assigning an IP address to a PC or router: static and automatic (DHCP). Static IP addresses are keyed in ...

Page 8 - cOnfiGurAtiOn; browser’s address field. The default; Basic: Administration

Signal Strength — Radio signals drop in power over distance, and even if all the settings are correct, low signal strength makes association impossible. The usable distance between the AP and client can range from a few meters indoors to a few kilometers. When setting up the client, make sure that: ...

Page 9 - Basic: IP Configuration; This screen allows you to select the IP Mode.; Basic: Operation mode; Operation Mode —

Basic: IP Configuration This screen allows you to select the IP Mode. Static IP — When you boot up the AP for the first time, it is in Static mode, and you assign a static IP. The default IP address, subnet mask and gateway mask are 192.168.10.100, 255.255.255.0 and 0.0.0.0. Dynamic IP (DHCP Client)...

Page 10 - AP Repeater Mode

Wireless Mode — The device operates in the frequency of 2.4 GHz for 802.11g. Radio Frequency — Set manually or use SmartSelect for automatic channel selection. WDS — enable, disable or disable with multiple PC support. When the wireless distribution system is enabled, all PCs connected to a bridge/A...

Page 11 - Wireless Bridge Mode

9. From the Basic: Site Survey screen, copy the MAC address (BSSID) of AP1 and add it to the Remote AP MAC Address list on the operation Mode screen. Click “Update” and “Reboot.” The operation Mode screen should now appear as below. 10. From the Status menu, go to the Association Status screen. Once...

Page 13 - Advanced: radio setting

MAC address of AP2 (bridge) must be in the Remote MAC Address list of AP1 (bridge). NOTE: Also, the default gateways of AP1 and AP2 should be the IP address of the router on your network. Advanced: radio setting Data Rate — You can enter different values, such as 11 Mbps or 24 Mbps; but “Best” lets ...

Page 14 - Advanced: security setting; traffic. Authentication can; WEP Security; Select “Hexadecimal” to enter the keys in hexadecimal; WPA Security; Enter the IP address of the RADIUS server (for 802.1x

Advanced: security setting This screen allows you to configure wireless encryption to prevent unwelcome parties from reading your traffic. Authentication can also be configured to block outsiders from accessing your network. Disable — No wireless security. WEP — Select to apply WeP security. WPA-PSK...

Page 15 - Enter the shared secret only if the 802.1x protocol is used.; Advanced: mAc Address control; enable or disable the function.; Advanced: protocol filter; Thi

RADIUS Secret — Enter the shared secret only if the 802.1x protocol is used. Key Update Interval — Specify the interval in milliseconds. The default is 1,800. Cipher Type — Select “Auto,” “TKIP” or “AeS.” Key Source — Specify the location of the key storage (only if 802.1x is used). If using PSK (Pr...

Page 16 - Save Configuration to Local Device —

Filter IPX Packet — Select to disallow all IPX packets from passing through. Wireless Isolation — Select to disallow wireless clients associated with this device from communicating with each other. Enable Broadcast Filter — Select to filter out broadcast storm. Broadcast Number Allowed — enter a val...

Page 17 - status: system status; most common configuration parameters are shown here.

Restore Configuration from Local PC — Allow the restoration of a “Good Config” from the computer system. Click “Browse” to find the location of the saved “Good Config” in the computer system. status: system status This screen presents a convenient overview of the overall status of the AP. The most c...

Page 18 - you to set the same username for both admin and super users.; super user: firmware upgrade; firmware will be named “apimg1.”; super user: firmware Version

status: Association status This screen presents an overview of the MAC address and signal strength (SNR in dBm) of all clients connected to the AP through the ethernet or wireless. super user: super user This screen allows you to change the username and password for admin user / end user. The defaul...

Page 19 - utility instAllAtiOn & OperAtiOn; PC Requirements; software installation; and select a new directory.; Operation; If the username and/or password of the devices has been changed, the

utility instAllAtiOn & OperAtiOn The Wireless Super G outdoor Poe Access Point and Bridge (“outdoor AP”) utility is easy-to-use software that lets an administrator quickly configure the AP at first boot-up. The utility only communicates with authorized access points and bridges, allowing them to...

Page 20 - installation reminders; should not attempt to install the device or change its settings.

• After the necessary changes have been made, the administrator can apply the changes to the AP. Check the “Reboot” box and click “Update” to reboot the device. • Multiple devices can be updated at the same time. Use CTRL/left-click to select multiple entries, or enter CTRl/A to select all entries. ...

Page 21 - specificAtiOns; Standards; - Automatically associate to WAP with identical eSSId; Wireless

specificAtiOns Standards • IEEE 802.11b (11 Mbps Wireless LAN) • IEEE 802.11g (54 Mbps Wireless LAN) • IEEE 802.11g+ (108 Mbps Wireless LAN) • IEEE 802.3 (10Base-T Ethernet) • IEEE 802.3u (100Base-TX Fast Ethernet) • SNMPv1/v2c (Simple Network Management Protocol) General • LAN ports: one RJ-45 10/1...

Intellinet Network Solutions 503679 - Manual

Table of Contents:

Summary

Other Intellinet Network Solutions Models