Page 2 - Copyright
PCM-3370 User’s Manual ii Copyright This document is copyrighted, © 2003. All rights are reserved. The origi-nal manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.No part of this manual may be reproduced, copied, translated or tr...
Page 3 - Packing List
iii Packing List Before you begin installing your card, please make sure that the following materials have been shipped:• 1 PCM-3370 all-in one single board computer• 1 CD-ROM or disks for utility, drivers, and manual (in PDF format)• 1 warranty certificate• 1 2.5" IDE flat cable, 44-pin to 44-p...
Page 4 - Additional Information and Assistance
PCM-3370 User’s Manual iv Additional Information and Assistance Step 1. Visit the Advantech web site at www.advantech.com where you can find the latest information about the product. Step 2. Contact your distributor, sales representative, or Advantech's cus- tomer service center for technical suppor...
Page 5 - Safety Instructions
v Safety Instructions 1. Read these safety instructions carefully.2. Keep this User's Manual for later reference.3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket mu...
Page 6 - Wichtige Sicherheishinweise
PCM-3370 User’s Manual vi Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.2. Heben Sie diese Anleitung für den späteren Gebrauch auf.3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein...
Page 9 - Content; Chapter
ix Content Chapter 1 General Information ........................................2 1.1 Introduction ....................................................................... 2 1.2 Features ............................................................................. 3 1.3 Specifications .................
Page 13 - General Information
CHAPTE R 1 General Information This chapter gives background infor-mation on the PCM-3370.Sections include: • Sections include:• Introduction• Features• Specifications• Board layout and dimensions
Page 14 - Chapter 1 General Information
PCM-3370 User’s Manual 2 Chapter 1 General Information 1.1 Introduction The PCM-3370 utilizes a PC/104+ form factor design that supports ULV Celeron 400/650 processors and LV Pentium III 800, 933 processors. This effective PC/104+ solution gives end users the choice of good, eco-nomical performance ...
Page 17 - Mechanical and environmental
5 Chapter 1 • Connection: On-board RJ-45 connector• Built-in boot ROM Mechanical and environmental • Max. power requirements:[email protected] for Intel Celeron ULV 400 @ 128M • Operating temperature: 0 ~ 60° C (32 ~ 140° F)• Dimensions (L x W): 96 mm x 115 mm (3.77" x 4.05")• Weight: 0.2Kg (0.48lb)
Page 18 - Board Dimensions
PCM-3370 User’s Manual 6 1.4 Board Dimensions Figure 1.1: Board Dimensions (Component Side)
Page 21 - Installation
CHAPTE R 2 Installation This chapter explains how to set up the PCM-3370 hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the instal-lation procedure.
Page 22 - Chapter 2 Installation
PCM-3370 User’s Manual 10 Chapter 2 Installation 2.1 Jumpers The PCM-3370 has a number of jumpers that allow you to configure your system to suit your application. The table below lists the function of each of the board's connectors and jumpers Table 2.1: connectors and jumpers Label Function CN1 Re...
Page 24 - Locating jumpers and connectors
PCM-3370 User’s Manual 12 2.2 Locating jumpers and connectors Figure 2.1: Locating Connectors and Jumpers CN2 J P1 CN1 J P2 J P3 CN2 CN4 CN5 CN6 CN8 CN9 CN1 3 CN1 4 CN1 7 J P4 J P5 CN1 9 CN2 0 CN1 1 CN1 8 CN22 CN3 CN1 6 CN15
Page 28 - SDRAM installation
PCM-3370 User’s Manual 16 2.4.3 COM1 and COM2 RI Input Select (JP4, JP5) There is Ring input select jumper at COM1 and COM2. 2.5 SDRAM installation There are one on-board 144-pin SODIMM socket. Table 2.4: COM1 and COM2 RI Input Select (JP4, JP5) JP4 COM1 RI Input Select Pin Function 1-2 RI * 2-3 VCC...
Page 30 - VGA interface connections
PCM-3370 User’s Manual 18 2.9 Power connectors (CN15, CN18) 2.9.1 Main power connector (CN15) The power connection is a 8-pin connector requiring +5 V and +12 V power. It needs a cable (1703080104 for AT or 1703200380 for ATX) to connect AT/ATX power supply. 2.9.2 ATX standby power input connector (...
Page 31 - Ethernet configuration
19 Chapter 2 CN7 is 40-pin Hirose connector and CN10 is 20-pin Hirose connector. It can connect to a 36-bit TFT LCD panel. Pin assignments appear in the appendix. (For more information on LCD connection information between CN7 and CN10 and an LCD, refer to Chapter 3.) 2.12.3 Invert Power Connector (...
Page 35 - Software Configuration
CHAPTE R 3 Software Configuration This chapter details the software con-figuration information. It shows you how to configure the card to match your application requirements. Award System BIOS will be covered in Chapter 4.Sections include: • Introduction• VGA display software configuration• LCD disp...
Page 36 - Chapter 3 Software Configuration; VGA display firmware configuration
PCM-3370 User’s Manual 24 Chapter 3 Software Configuration 3.1 Introduction The PCM-3370 system BIOS and custom drivers are located in a 256 KB, 32-pin (JEDEC spec.) Flash ROM device, designated U23. A single Flash chip holds the system BIOS, VGA BIOS, and network Boot ROM image. The display can be ...
Page 38 - Connections for four standard LCDs
PCM-3370 User’s Manual 26 3.3 Connections for four standard LCDs Connections to Sharp LM64183P (640 x 480 DSTN MONO LCD) * LM64183P requires -17 V for VEEConnections to PLANAR EL640.480-AM1 (640 x 480 EL LCD) Table 3.1: Sharp LM64183P LCD (CN35) LM64183P PCM-3370 (CN35) Pin Name Pin Name CN1-1 S 36 ...
Page 42 - Ethernet software configuration
PCM-3370 User’s Manual 30 3.4 Ethernet software configuration The PCM-3370’s on-board Ethernet interface supports all major network operating systems. To configure the medium type, to view the current configuration, or to run diagnostics, do the following:1. Power the PCM-3370 on. Ensure that the RS...
Page 43 - Award BIOS Setup
CHAPTE R 4 Award BIOS Setup This chapter describes how to set BIOS configuration data.
Page 44 - Chapter 4 Award BIOS Setup; System test and initialization
PCM-3370 User’s Manual 32 Chapter 4 Award BIOS Setup 4.1 System test and initialization These routines test and initialize board hardware. If the routines encoun-ter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors...
Page 45 - Award BIOS setup
33 Chapter 4 4.2 Award BIOS setup Awardís BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. 4.2.1 Entering setup Power ...
Page 55 - AGP 4X Setup
CHAPTE R 5 AGP 4X Setup The PCM-3370 features an onboard AGP 4X flat panel/VGA interface. This chapter provides instructions for installing and operating the software drivers on the included display driver diskette.
Page 56 - Chapter 5 AGP 4X Setup
PCM-3370 User’s Manual 44 Chapter 5 AGP 4X Setup 5.1 Introduction The PCM-3370 has an onboard AGP flat panel/VGA interface. The spec-ifications and features are described as follows: 5.1.1 Chipset The PCM-3370 uses a VIA Twister 8606T chipset from VIA Technology Inc. for its AGP/SVGA controller. It ...
Page 58 - Installation of the SVGA Driver
PCM-3370 User’s Manual 46 5.2 Installation of the SVGA Driver Complete the following steps to install the SVGA driver. Follow the pro-cedures in the flow chart that apply to the operating system that you are using within your PCM-3370. 5.2.1 Installation for Windows 95 1. Select "Start", ...
Page 83 - Further Information
71 Chapter 5 10. Press “Finish" to reboot. 5.3 Further Information For further information about the AGP/VGA installation in your PCM-3370, including driver updates, troubleshooting guides and FAQ lists, visit the following web resources: VIA website: www.via.com.tw Advantech websites: www.advan...
Page 86 - Chapter 6 PCI Bus Ethernet Interface; Installation of Ethernet Driver
PCM-3370 User’s Manual 74 Chapter 6 PCI Bus Ethernet Interface 6.1 Introduction The PCM-3370 is equipped with a high-performance 32-bit Ethernet chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by major network operating systems. It is also both 100Base-T ...
Page 99 - Further information
87 Chapter 6 6.3 Further information Realtek website: www.realtek.comAdvantech websites:www.advantech.com www.advantech.com.tw
Page 102 - A.1 Programming the watchdog timer
PCM-3370 User’s Manual 90 Appendix A Programming the Watchdog Timer A.1 Programming the watchdog timer The following example show how you might program the watchdog timer in Assembly: 1. Watch Dog Timer Enable Port 404e Bit7 set "o" to enable PCM-3370 Watch Dog TimerEx:Mov DX, 404eMov AL, 7F...
Page 103 - Jumper Settings
Appendix B Jumper Settings The PCM-3370 is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environments.
Page 104 - Appendix B PCM-3370F Jumper Settings
PCM-3370 User’s Manual 92 Appendix B PCM-3370F Jumper Settings Table B.1: Connectors 1. CN1 Reset Connect 2. CN2 Invert Power Connect 3. CN3 IR Connect CN4 FAN Connector 5. CN5 LAN Connector 6. CN6 422/485 Connect 7. CN7 40-pin LCD Port (24bit) 8. CN8 CRT Connect 9. CN9 USB Connector 10. CN10 20-Pin...
Page 105 - B.1 CN1 Reset Connector
93 Appendix B B.1 CN1 Reset Connector B.2 CN2 Inverter Power Connector Table B.2: CN1 Reset Connector Pin Pin name 1 Signal 2 GND Table B.3: CN2 Inverter Power Connector 1 +12V 2 GND 3 ENABKL 4 VBR 5 +5V 1 2 5 4 2 3 1
Page 107 - B.5 CN5 LAN Connector
95 Appendix B B.5 CN5 LAN Connector Table B.6: CN5 LAN Connector Pin Pin name 1 VCC_LAN 2 ACTLED 3 RX+ 4 RX- 5 LILED 6 GND 7 NC 8 GND 9 TX+ 10 TX- 4 5 3 6 1 2 810 79
Page 109 - B.8 CN8 CRT Connector
97 Appendix B B.8 CN8 CRT Connector 35 SHFCLK 36 FLM(V-SYNC) 37 M/(DE) 38 LP(H-SYNC) 39 ENABKL 40 ENVEE Table B.9: CN8 CRT Connector 1 RED 2 DDC POWER(+5V) 3 GREEN 4 GND 5 BLUE 6 NC 7 NC 8 DDC DATA 9 GND 10 H-SYNC 11 GND 12 V-SYNC 13 GND 14 DDC CLOCK 15 GND 16 NC 8 7 9 3 3 3 3 2 4 4 1 0 4 14 15 3 16...
Page 110 - B.9 CN9 USB Connector; CN9 USB Connector
PCM-3370 User’s Manual 98 B.9 CN9 USB Connector Table B.10: CN9 USB Connector 1 +5V 2 +5V 3 D0- 4 D1- 5 D0+ 6 D1+ 7 GND 8 GND 9 GND 10 NC 31 10 8642 5 7 9
Page 115 - CN15 Power Conector
103 Appendix B B.15 CN15 Power Conector 17 Data 7 18 GND 19 ACK- 20 GND 21 BUSY 22 GND 23 PaperEmpty 24 GND 25 SELECT 26 N/C Table B.16: CN15 Power Conector 1 +5V 2 +5V 3 +5V 4 GND 5 GND 6 GND 7 GND 8 +12V 4 26 25 3 24 23 1 2 54 2 3 1 6 7 8
Page 117 - B.18 CN18 ATX Power Connector
105 Appendix B B.17 CN17 KB/MS Connector B.18 CN18 ATX Power Connector Table B.18: CN17 KB/MS Connector Pin Pin name 1 KB CLOCK 2 KB DATA 3 MS CLOCK 4 GND 5 +5V 6 MS DATA Table B.19: CN18 ATX Power Connector Pin Pin name 1 +5V Standby 2 GND 3 PSON 5 4 2 3 1 6
Page 120 - B.24 JP2 Watchdog Timer
PCM-3370 User’s Manual 108 B.22 CN22 RTC Connector B.23 JP1 COMS Charge&Discharge B.24 JP2 Watchdog Timer Table B.23: CN22 RTC Connector Pin Pin name 1 Signal 2 GND Table B.24: JP1 COMS Charge&Discharge Pin Function 1-2 Charge * 2-3 Discharge Table B.25: JP2 Watchdog Timer Pin Function 1-2 R...
Page 121 - B.25 JP3 PCI VIO Select; JP3 PCI VIO Select
109 Appendix B B.25 JP3 PCI VIO Select B.26 JP4 COM1 RI Input Select Table B.26: JP3 PCI VIO Select Pin Function 1-2 VCC 2-3 VCC3 Default NULL * Table B.27: JP4 COM1 RI Input Select Pin Function 1-2 RI * 2-3 VCC 1 2 3 1 2 3 VCC VCC3 1 2 3 1 2 3 RJ* VCC
Page 122 - B.27 JP5 COM2 RI Input Select
PCM-3370 User’s Manual 110 B.27 JP5 COM2 RI Input Select Table B.28: JP5 COM2 RI Input Select Pin Function 1-2 RI * 2-3 VCC 1 2 3 1 2 3 RJ* VCC
Page 123 - System Assignments
Appendix C System Assignments • System I/O ports • DMA channel assignments • Interrupt assignments
Page 124 - Appendix C System Assignments
PCM-3370 User’s Manual 112 Appendix C System Assignments C.1 System I/O ports Table C.1: System I/O ports Addr. range (Hex) Device 000-01F DMA controller (slave) 020-03F Interrupt controller 1, (master) 040-05F 8254 timer/counter 060-06F 8042 (keyboard controller) 070-07F Real-time clock, non-maskab...
Page 125 - C.2 DMA channel assignments
113 Appendix C C.2 DMA channel assignments 443 Watchdog timer ** default setting Table C.2: DMA channel assignments Channel Function 0 Available 1 Available 2 Floppy disk (8-bit transfer) 3 Parallel** 4 Cascade for DMA controller 1 5 Available 6 Available 7 Available ** Parallel port DMA default set...
Page 126 - C.3 Interrupt assignments
PCM-3370 User’s Manual 114 C.3 Interrupt assignments Table C.3: Interrupt assignments Interrupt# Interrupt source NMI Parity error detected IRQ 0 Interval timer IRQ 1 Keyboard IRQ 2 Interrupt from controller 2 (cascade) IRQ 3 Serial communication port 2 IRQ 4 Serial communication port 1 IRQ 5 Availa...
Page 127 - st MB memory map
115 Appendix C C.4 1st MB memory map Table C.4: 1st MB memory map Addr. range (Hex) Device F000h - FFFFh System ROM E000h - EFFFh Reserved for BIOS boot CC00h - DFFFh available C000h - CB00h VGA BIOS B800h - BFFFh CGA/EGA/VGA text B000h - B7FFh Reserved for graphic mode usage A000h - AFFFh EGA/VGA g...
