Integra DTR-5.5 - Manual

5 Features Amplifier • 7-channel amplifier • Optimum Gain Volume Circuitry • Zone 2 capability • 24-bit/192 kHz D/A converters • WRAT (Wide Range Amplifier Technology) • Color-coded speaker terminal posts Audio/Video • Dolby *1 Digital, Dolby Digital EX, Dolby Pro Logic IIx • DTS *2 , DTS-ES Discret...

6 Table of Contents Basic Introduction Important Safety Instructions .......................................................................................... 2Precautions ....................................................................................................................... 3Suppli...

7 Table of Contents —Continued Advanced Controlling Other Components Entering a Remote Control Codes................................. 80Learning Commands from Another Remote Controller ..................................................................... 88 Using Macros.................................

8 Front & Rear Panels Front Panel Standby Zone 2 1 Z Y W V U X 5 6 789 J K M N Q T S O P R L 2 3 4 Standby Zone 2 1 Z Y W V U X 5 678 J K L N O R T P Q S M 2 3 4 9 DTR-6.5 DTR-5.5 DTR-6.5,5.5̲En.book Page 8 Wednesday, July 28, 2004 9:07 AM

9 Front & Rear Panels —Continued For detailed information, see the pages in parentheses. A Standby/On button (38) This button is used to set the AV receiver to On or Standby. For models with a POWER switch, this button has no effect unless the POWER switch is set to ON. B Standby indicator (38) ...

10 Front & Rear Panels —Continued For detailed information, see the pages in parentheses. 1 MUTING indicator (54) This indicator flashes while the AV receiver is muted. 2 REC OUT indicator (64) This indicator lights up when the REC OUT is selected. 3 ZONE 2 indicator (77) This indicator lights u...

11 Front & Rear Panels —Continued For detailed information, see the pages in parentheses. A COMPONENT VIDEO IN 1, 2, 3 (28, 30, 32) These component video inputs can be used to con-nect AV components with component video outputs, such as DVD players. B AM ANTENNA (24) These push terminals are for...

12 Front & Rear Panels —Continued J OPTICAL DIGITAL (27, 28, 30, 32, 34, 35) The DTR-5.5 doesn’t have an IN 4 jack. The optical digital audio inputs can be used to con-nect CD and DVD players, and other components with an optical digital audio output. The optical output can be used to connect a ...

13 Remote Controller Notes: • The batteries should last for about six months, although this will vary with usage. • If the remote controller doesn’t work reliably, try replacing the batteries. • Don’t mix new and old batteries or different types of batteries. • If you intend not to use the remote co...

14 Remote Controller —Continued In addition to controlling the AV receiver, the remote controller has several operating modes for controlling your other AV components, including Integra compo-nents connected via . Modes are selected by using the remote controller’s Remote Mode buttons.For detailed i...

16 Remote Controller —Continued DVD mode is used to control an Integra DVD player connected to the AV receiver via . To set the remote controller to DVD mode, press the [DVD] Remote Mode button. A Standby button This button is used to set the DVD player to Standby. B On button This button is used to...

17 Remote Controller —Continued N A-B button This button is used to set the A–B repeat playback function. O Open/Close [ ] button This button is used to open and close the disc tray. P Video Off button This button is used to turn off the internal video cir-cuitry, eliminating any possibility of inte...

18 Remote Controller —Continued MD/CDR mode is used to control an Integra MiniDisc recorder or CD recorder connected to the AV receiver via . To select MD/CDR mode, press the [MD/CDR] Remote Mode button. By default, this button is set to control a MiniDisc recorder. To control a CD recorder, it must...

19 Remote Controller —Continued M FR & FF [ ]/[ ] buttons The FR [ ] button is used to start fast reverse. The FF [ ] button is used to start fast forward. N Stop [ ] button This button is used to stop playback. O Random button This button is used with the random playback func-tion. P Memory but...

20 About Home Theater Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With analog and digital TV you can enjoy Dolby Pro Log...

21 Connecting the AV receiver • Before making any AV connections, read the manuals supplied with your other AV components. • Don’t connect the power cord until you’ve completed and double-checked all AV connections. Optical Digital Jacks The AV receiver’s optical digital jacks have shutter-type cove...

22 Connecting the AV receiver —Continued Speaker Configuration For the best surround-sound experience, you should con-nect seven speakers and a powered subwoofer. The following table indicates the channels you should use depending on the number of speakers that you have. *If you’re using only one su...

23 Connecting the AV receiver —Continued Speaker Connection Precautions Read the following before connecting your speakers:• American model only: Only connect speakers with an impedance of 6 ohms or higher. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a...

24 Connecting the AV receiver —Continued This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect th...

25 Connecting the AV receiver —Continued Connecting an Outdoor FM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out-door FM antenna instead. Notes: • Outdoor FM antennas work best outside, but usable results can sometimes be obtained w...

26 Connecting the AV receiver —Continued By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver. The AV receiver supports ...

27 Connecting the AV receiver —Continued Monitor Out ■ Using Composite Video Use a composite video cable to connect the AV receiver’s V MONITOR OUT jack to a composite video input on your TV, as shown. ■ Using S-Video Use an S-Video cable to connect the AV receiver’s S MONITOR OUT jack to an S-Video...

28 Connecting the AV receiver —Continued Video Connections You only need to use one of the following connection methods. ■ Using Composite Video Use a composite video cable to connect the AV receiver’s V DVD IN jack to the composite video output on your DVD player, as shown. ■ Using S-Video Use an S...

29 Connecting the AV receiver —Continued ■ Using a Multichannel Connection If your DVD player supports multichannel audio formats such as DVD-Audio, and it has a 5.1-channel analog audio output, you can enjoy DVD-Audio playback.Use a multichannel analog audio cable to connect the AV receiver’s DVD I...

30 Connecting the AV receiver —Continued This section shows how to connect a VCR for playback so that you can watch videos via the AV receiver. Video Connections • Use an S-Video cable to connect the AV receiver’s S VIDEO 1 IN jack to a S-Video output on your VCR, as shown. OR• Use a composite video...

31 Connecting the AV receiver —Continued This section explains how to connect a VCR for recording from a TV or another VCR. Video Connections • Use an S-Video cable to connect the AV receiver’s S VIDEO 1 OUT jack to an S-Video input on the recording VCR. Use another S-Video cable to connect the AV r...

32 Connecting the AV receiver —Continued Video Connections You only need to use one of the following connection methods. ■ Using Composite Video Use a composite video cable to connect the AV receiver’s V VIDEO 3 IN jack to a composite video output on your video source, as shown. ■ Using S-Video Use ...

34 Connecting the AV receiver —Continued ■ Using Optical or Coaxial Connections If you connect to a digital audio input, you’ll need to assign it (see page 42).• Use an optical digital audio cable to connect one of the AV receiver’s OPTICAL DIGITAL IN jacks to the optical output on your CD player, a...

35 Connecting the AV receiver —Continued ■ Using Optical or Coaxial Connections (playback only) If you connect to a digital audio input, you’ll need to assign it (see page 42).• Use an optical digital audio cable to connect one of the AV receiver’s OPTICAL DIGITAL IN jacks to the optical output on y...

36 Connecting the AV receiver —Continued For the DTR-6.5 The AV receiver’s PHONO IN is designed for use with a moving magnet (MM) type cartridge. Use an analog audio cable to connect the AV receiver’s PHONO IN L/R jacks to the audio output on your turn-table, as shown. Notes: • If your turntable has...

37 Connecting the AV receiver —Continued If you want to connect a more powerful power amplifier and use the AV receiver as a preamp, you can connect one to the PRE OUT jacks. In this case, you should con-nect all speakers and the subwoofer to that power ampli-fier. However, if you have a powered sub...

38 Connecting the AV receiver —Continued The AV receiver has AC outlets on its rear panel that can be used to connect the power cords of AV other compo-nents that you intend to use with the AV receiver. These components can then be left turned on so that they turn on and off as and when the AV recei...

39 First Time Setup This chapter explains the settings that you need to make before using the AV receiver. With the supplied speaker setup microphone, the Auto-matic Speaker Setup function can measure the test tone output by each speaker and automatically determine the number of speakers connected, ...

40 First Time Setup —Continued 3 Press [Enter]. The automatic speaker setup starts.The test tone, which is somewhat loud, is output by each speaker in turn, mea-sured by the microphone, and the speaker settings set accordingly. The whole process takes about 90 seconds. If any extraneous noise is pic...

41 First Time Setup —Continued The AV receiver is configured using onscreen setup menus, which are displayed on the TV that’s connected to either of the MONITOR OUT jacks. Because they appear on your TV, they’re large and clear, making setup a breeze.Settings are divided into two groups: Basic Setup...

42 First Time Setup —Continued Digital Input If you connect a component to a digital input jack, you must assign that jack to an input selector. For example, if you connect your CD player to the OPTICAL IN2 jack, you should assign that jack to the CD input selector. By default, the OPTICAL IN1 jack ...

43 First Time Setup —Continued Component Video Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector. For example, if you connect your DVD player to COMPONENT IN 3, you should assign it to the DVD input selector. If you want to output composite and S-Video sources fro...

44 First Time Setup —Continued Minimum Speaker Impedance (not American models) If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, set the Minimum Speaker Impedance to “4 ohms.” Note: Before you change this setting, turn down the volume. Notes: • This procedure...

46 First Time Setup —Continued Some of the settings in this section are set automatically by the Automatic Speaker Setup function (see page 39).Here you can check the settings made by the Automatic Speaker Setup function, or set them manually, which is useful if you change one of the connected speak...

47 First Time Setup —Continued Crossover Notes: • If the crossover frequency is set to a low value, and the program material doesn’t contain any sounds below that frequency, the subwoofer will not output much sound. 6 Use the Up and Down [ ]/[ ] buttons to select “c. Center,” and then use the Left a...

48 First Time Setup —Continued Double Bass With the Double Bass function, you can boost bass out-put by feeding bass sounds from the front left and right channels to the subwoofer. This function can be set only if the Subwoofer setting in step 4 is set to Yes, and the Front setting in step 5 is set ...

49 First Time Setup —Continued Notes: • On the DTR-6.5, if the distance between the furthest and nearest speakers is greater than 20 feet (6 meters), corrected values suitable for home theater use will be set automatically. • On the DTR-5.5, the Center and Subwoofer distances can be set up to 5 ft. ...

50 First Time Setup —Continued Speaker Level Calibration Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Notes: • The speakers cannot be calibrated while the output of the AV receiver is muted, while ...

51 First Time Setup —Continued Equalizer Setting Here you can adjust the EQ of individual speakers. The volume of individual speakers can be set on page 50. Notes: • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. 1 Press the [R...

52 First Time Setup —Continued If you connect an -compatible Integra MiniDisc recorder or CD recorder to the TAPE IN/OUT jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. Changing the TAPE/MD/CDR Display 1 Press the [TAPE] input selector ...

53 Basic Operation This section explains how to select the input source (i.e., the AV component that you want to listen to or watch). Selecting the Input Source Standby Zone 2 1 3 O n Standby T V Display Muting E xit G u id e Prev CH T V CH T V VOL --/--- Dimmer Tape T V Input Sleep Input I Enter To...

54 Basic Operation —Continued You can adjust the brightness of the display. You can temporarily mute the output of the AV receiver. With the sleep timer, you can set the AV receiver to auto-matically turn off after a specified period. If you need to cancel the sleep timer, press the [Sleep] button r...

55 Basic Operation —Continued You can display various information about the current input source as follows. The following information can typically be displayed for input sources. *If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling fre-quency...

56 Basic Operation —Continued With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. Listening to the Radio Tuning into Radio Stations ■ Auto Tuning Mode When tuned into a station, the TUNED indicator appears. When tuned i...

57 Basic Operation —Continued Presetting Radio Stations You can store up to 40 of your favorite radio stations as presets. Selecting Preset Stations Deleting Presets Displaying Radio Information 1 Tune into the station that you want to store as a preset. 2 Press the [Memory] button. The MEMORY indic...

58 Basic Operation —Continued See “About the Listening Modes” on page 60 for detailed information about the listening modes. Selecting on the AV receiver ■ [Stereo] button This button selects the Stereo listening mode. ■ Listening Mode [ ] [ ] buttons These buttons select all the listening modes tha...

59 Basic Operation —Continued The following table lists all the listening modes and shows which modes can be selected for each input signal format. Input signal format Analog, PCM*1 1. In the Pure Audio and Direct listening modes, PCM signals at 32 kHz, 44.1 kHz, and 48 kHz are processed at 64 kHz, ...

60 Basic Operation —Continued About the Listening Modes With its built-in surround-sound decoders and DSP pro-grams, the AV receiver can transform your home listen-ing room into a movie theater or concert hall. If you connect two surround back speakers (i.e., left and right), both will be used for 6...

61 Basic Operation —Continued DTS-ES Matrix This is DTS with an added surround back channel for 6.1 surround sound. Use it to provide 6.1 channel surround playback with program material recorded in DTS 5.1 format. Since DTS 5.1 program material contains surround back channel informa-tion, all channe...

62 Advanced Operation With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone. Notes: • The effect of the Lat...

63 Advanced Operation —Continued You can adjust the level of individual speakers during playback. These adjustments are temporary and will be cancelled when the AV receiver is set to Standby. Notes: • You cannot use this function while the AV receiver is muted. • Speakers that are set to No or None ...

64 Advanced Operation —Continued This section explains how to record the current input source, how to record one input source while enjoying another, and how to dub audio onto your video record-ings. Unless you have the full consent of the copyright holder, copyright laws prohibit using your recordi...

65 Advanced Operation —Continued AV Recording You can record AV input sources to an AV recording component (VCR, etc) connected to the VIDEO 1 OUT or VIDEO 2 OUT. See pages 27–38 for information on connecting components. Recording Separate AV Sources Here you can record audio and video from complete...

66 Advanced Setup Here are surround-related settings for PCM, Dolby Dig-ital, multichannel, and other input signal formats. Note: • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. • The Surround Mode and SurrBack Mode settings c...

67 Advanced Setup —Continued ■ c. SurrBack Mode This setting determines which surround mode is used for Dolby Digital input signals that don’t contain a Dolby Digital EX flag, or when the b. Dolby EX setting is set to Manual. This setting is unavailable if no surround back speakers are connected.You...

68 Advanced Setup —Continued Here you can set listening mode-related settings and functions. Note: • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. Audio Adjust Functions 1 Press the [Receiver] button fol-lowed by the [Setup] b...

69 Advanced Setup —Continued 4-1. Mono ■ a. Output Channel This setting determines which speakers are used to out-put mono audio when the Mono listening mode is used. L/R: Mono audio is output from the front left and right speakers (default). Center: Mono audio is output from the center speaker. ■ b...

70 Advanced Setup —Continued 4-9. Theater-Dimensional These settings apply to the Theater-Dimensional listen-ing mode. ■ a. Listening Angle With this setting, you can specify the angle of the front left and right speakers relative to the listening position.Processing for the Theater-Dimensional list...

71 Advanced Setup —Continued Note: • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. This section explains the items on the Preference menu. Note: • This procedure can also be performed on the AV receiver by using its [Setup] bu...

73 Advanced Setup —Continued 6-5. Digital Format ■ b. Digital Format This setting does not apply to input selectors not assigned to a digital input jack.With this setting, you can set a digital input to DTS, PCM, or Auto. This can be set for each input selector individually.Use the Up and Down [ ]/[...

74 Zone 2 With the Zone 2 function, you can enjoy one input source in the main room and a different source in another room.There are two connection methods: using a receiver/inte-grated amp in Zone 2 or using only a pair of speakers in Zone 2. Using a Receiver/Integrated Amp in Zone 2 With this conn...

75 Zone 2 —Continued To use Zone 2, you must make this setting. It enables the speakers connected to the ZONE 2 SPEAKERS termi-nals so that they produce sound when Zone 2 is used. Note: • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] ...

76 Zone 2 —Continued The ZONE 2 OUT L/R jacks can also be used as pre outs. Setting the Zone 2 Out 1 Press the [Receiver] button fol-lowed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “1. Initial Setup,” and then press [Enter]. The Initial Se...

77 Zone 2 —Continued Here you can turn on Zone 2, select an input source, and adjust the volume. Note: To control Zone 2 with the remote controller, you must press the [ZONE 2] button first. Notes: • If the Sleep function has been set, the Zone 2 compo- nent will turn off along with the AV receiver ...

78 Zone 2 —Continued Using the 12V Trigger When the AV receiver’s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V TRIGGER IN jack on a connected component, the AV receiver can be configured so that the component is turned on automatically when Zone 2 is used. See page 73 for details. Adjusting ...

79 Zone 2 —Continued Using a Multiroom Kit with a Cabinet In the following diagram, an IR receiver picks up the infrared signals from the remote controller and feeds them to the AV receiver in the cabinet via the connecting block.• On the Remote Setup menu, set the IR IN Position set- ting to “Main”...

80 Controlling Other Components You can use the AV Receiver’s remote controller (RC-588M/RC-590M/RC-591M) to control your other com-ponents, including those made by other manufacturers. This chapter explains how to:• Enter the remote control code for a component that you want to control (e.g., DVD, ...

81 Controlling Other Components —Continued Resetting Remote Mode Buttons If you’ve entered another code for one of these button and now want to return to the default, perform the fol-lowing procedure.By default, some REMOTE MODE buttons are prepro-grammed with remote control codes for controlling In...

82 Controlling Other Components —Continued Remote Control Codes When two or more codes are given, try each one in turn, and choose the one that works best.Depending on the manufacturer and component, the remote controller may not work as expected. DVD (DVD player) Manufacturer Control code Aiwa 5010...

86 Controlling Other Components —Continued To control another component, point the remote control-ler at it and use the buttons as explained below (you must select the appropriate remote control mode first). Controlling a TV Buttons marked with an asterisk can always be used to control a TV regardle...

87 Controlling Other Components —Continued Controlling a VCR The following buttons control the AV Receiver.[VOL]: Adjusts the volume of the AV receiver.[Muting]: Mutes the AV Receiver. Controlling a Satellite Receiver The following buttons control the AV Receiver.[VOL]: Adjusts the volume of the AV ...

89 Controlling Other Components —Continued With the Macro function, you can program the remote controller’s Macro buttons to perform a sequence of actions with just one button press. For example, nor-mally you need to perform the following actions to play a CD: 1. Press the Remote Mode [[[[R R R Ree...

90 Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit. Can’t turn on the AV receiver? • Make sure that the power cord is properly plugged into the wall outle...

92 Troubleshooting —Continued Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t appear? • Relocate your antenna.• Move the AV receiver away from your TV or com- puter. • Listen to the station in mono (page 56).• When listening to an AM station, operating the remote...

93 Troubleshooting —Continued The sound changes when I connect my head-phones? • When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Direct, or Pure Audio. When you disconnect the head-phones, the previous listening mode will be resumed. Th...

96 SN 29343827 (C) Copyright 2004 ONKYO CORPORATION Japan. All rights reserved. I0407-1 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A.Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales &a...