Page 2 - Before Start; Connections; About the Basic Manual; Speaker Ca
Before Start Step 1: Connections 2 About the Basic Manual The Basic Manual leads you through the fundamental steps to enjoy the AV Receiver from connections to TV, speaker system and playback components, to necessary functions for playback. As well as that, Basic Manual informs you with the instruct...
Page 3 - Connecting the TV and players; Important; HDMI cable connection
Step 1: Connections 3 1 Connecting the TV and players Important : The power cord must be connected only after all other connections are completed. HDMI cable connection The unit has many HDMI jacks on its rear panel and each of them corresponds to an input selector button of the same name on the fro...
Page 4 - Connecting Components without HDMI; Audio signal connection
4 Step 1: Connections Home on the remote controller, select "Setup" - "1. Input/ Output Assign" - "Monitor Out" and set the default value of "MAIN" to "SUB" or "MAIN+SUB". The unit supports the HDMI Through function that allows transmission from player...
Page 5 - Connecting speakers
5 Step 1: Connections 2 Connecting speakers Important : The power cord must be connected only after all other connections are completed. 45 78 12 9F 6 3 1 2 Front speakers 3 Center speaker 4 5 Surround speakers 6 Subwoofer 7 8 Surround back speakers 9 F Height speakers • 5.1 ch: 1 2 3 4 5 6 • 7.1 ch...
Page 6 - Setting Up; When using commercially available banana plugs; Other connections; Headphones connection
Step 2: Setting Up 6 Step 1: Connections 1/2"-5/8"(12-15 mm) Cut and remove the plastic coating from the end of the speaker cable, twist the core and connect it to the terminal. Make correct connection between the unit's jacks and speaker's jacks (+ to + and - to -) for each channel. If conn...
Page 7 - Turning the power on; Firmware update notification; st Step : AccuEQ Room Calibration; Place the speaker setup microphone.
7 Step 2: Setting Up Important : When the unit is turned on for the first time, the setup wizard of the section 2 will automatically be launched. If you use the setup wizard to make the initial setup, connect a TV to the HDMI OUT MAIN jack of the unit via HDMI connection. 1 Turning the power on Conn...
Page 8 - nd Step : Source Connection
8 Step 2: Setting Up 2. After placing the microphone at the measurement position, select "Do it Now" in the start screen and press Enter. 3. Connect the microphone to the Setup Mic jack of the unit. Setup Mic jack Speaker setup microphone 4. Follow the guidance displayed on the TV screen. Ac...
Page 9 - th Step : Network Connection; Exiting the setup wizard
9 Step 2: Setting Up 4th Step : Network Connection Do you want to connect network connection?It gives you network services that our AV receiver support. If you wish to skip this step.select “No. Skip”. YesNo. Skip HOME Exit Initial Setup Network Connection You can check the network connection and ...
Page 10 - Playing Back; Playing the player and TV
Step 3: Playing Back 10 1 Playing the player and TV To control the unit : You can control any other device than this unit if you register the specified remote control code to 3 Remote Mode. As the remote controller may be in the remote mode that enables control of other devices, be sure to press 2...
Page 11 - Listening modes; Other useful functions; TUNED
11 Step 3: Playing Back Listening modes Select the desired mode by switching and listening actual sound in different modes. The selectable listening modes depend on the format of the input signals. Movie/TV : You can select a listening mode suitable for movies and TV programs. Music : You can select...
Page 12 - Pairing
12 Step 3: Playing Back 3 Connecting and playing the Bluetooth-enabled device You can wirelessly enjoy music files stored in a smartphone or other Bluetooth-enabled device. The coverage area is 48 feet (15 meters). • The Bluetooth-enabled device needs to support the A2DP profile. • Note that connect...
Page 13 - Using Quick Setup menu
13 Step 3: Playing Back USB : Select "USB" in the TV screen and connect a USB storage device to the USB port on the front panel. On the TV screen, select the desired folder or music file with the cursors of the remote controller and press Enter to confirm and start playback. • "USB"...
Page 14 - Change the setting
14 Step 3: Playing Back 6 Using the multi-zone function The function allows you to connect the unit with an audio equipment placed in a separate room so that you can enjoy audio of the connected equipment even if you are staying in a different room. It is possible to perform playback in the main roo...
Page 15 - Performing Multi-zone Playback
15 Step 3: Playing Back Performing Multi-zone Playback 1. Press Zone2 on the remote controller, point the remote controller at the remote controller sensor and press z Receiver. "Z2" stays lit on the main unit display and the multi-zone function is enabled. 2. Press Zone2 again on the remote...
Page 16 - Front Panel
16 1 2 4 3 J K 5 7 6 8 9 F G I N M L S T Q O P H R (Australian model) Front Panel 1 z On/Standby button : Turns the unit on or into standby mode. 2 Bluetooth indicator : Flashes while pairing with a Bluetooth-enabled device is in progress and stays lit when pairing is completed. 3 Wi-Fi indicator : ...
Page 17 - Rear Panel
17 1 4 G 2 3 5 6 7 8 9 F I J H K L M Rear Panel 1 RI REMOTE CONTROL jack : An Onkyo product with RI jack can be connected and synchronized with this unit. 2 FM ANTENNA jack (75 Ω) and AM ANTENNA terminal : The supplied antennas are connected. 3 COMPONENT VIDEO IN/OUT jacks : Component video input/ou...
Page 18 - Troubleshooting; Display
Troubleshooting 18 1 4 6 2 3 7 5 9 8 Display 1 Stays lit or flashes in the following conditions. "Z2": Zone 2 output is on. "HDMI": HDMI signals are input and the HDMI input selector is selected. "ARC" (Audio Return Channel): Audio signals are input from the ARC compatible TV...
Page 20 - Specifications
Specifications 20 Amplifier Section Rated Output Power All channels: 95 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% (FTC) 115 watts minimum continuous power per channel, 6 ohm loads, 2 channels dri...
Page 21 - License and Trademark Information
21 License and Trademark Information Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & D...
Page 22 - DISCLAIMER
22 DISCLAIMER Through this device you are able to link to other services or websites which are not under the control of any company which has designed, manufactured or distributed/have distributed this device, and its affiliates (collectively, “Company”). We have no control over the nature, content ...
