Insignia NS-MG1205-C - Manual

5 68” METAL AND GLASS TV STAND www.insigniaproducts.com ASSEMBLY INSTRUCTIONS Step 1: Preparing the bases • Insert two suctions cups into the front base ( B ) and two suctions cups in the back base ( C ). You’ll need: O (4) NS-MG1205-C_14-0264_MAN_V1_ENG.fm Page 5 Wednesday, April 30, 2014 3:29 PM

6 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 2: Attaching the front base to the front support • From the inside of the front base ( B ), insert a short screw ( M ) through the screw hole on each tab and into the screw holes on the front support ( A ). Make sure that the tabs with the...

7 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 3: Attaching the side bases to the back base 1 From the inside of the back base ( C ), insert short screws ( M ) through the screw holes on the tabs and into the screw holes on the left base ( D ). On the back base ( C ), make sure that th...

8 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 4: Attaching the left and right bases to the front support • Slide the ends of the left base ( C ) and right base ( E ) into the openings on the front support ( A ). Make sure that the two screw holes on the bottom of each base and the scr...

9 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 5: Attaching the top frame • Align the screw holes in the tabs on the ends of the top frame ( R ) with the screw holes on the inside top of the front support ( A ). Insert short screws ( M ) through the screw holes on the tabs and into the...

10 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 6: Attaching the rear support panel • Insert long screws ( N ) through the screw holes on the rear support panel ( F ) and into the screw holes on the top frame ( R ) and back base ( C ). Use the Allen wrench ( Q ) to tighten the screws. ...

11 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 7: Attaching the feet • Flip the stand so the rear support panel ( F ) is facing up. Screw a foot ( K ) into the each of the bottom four corners of the front support frame ( A ) and the bottom corners of the rear support panel ( F ). You’...

12 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 8: Attaching the top shelf and piller supports 1 Attach a shelf pad ( S ) to each of the top corners on the rear support panel ( F ). 2 Align the screw holes on the top shelf ( G ) with the screw holes in the top of the front support ( A ...

13 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 9: Installing the middle shelf 1 From the front of the stand, slide the middle shelf ( I ) into the shelf bracket on the rear support panel ( F ). Make sure that the screw holes in the middle shelf face the front of the stand and the blac...

14 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 10: Install the bottom shelf • From the front of the stand, insert the bottom shelf ( J ). Make sure that the notch of the bottom shelf ( J ) faces the back of the stand and fits around the rear support panel ( F ). NS-MG1205-C_14-0264_MA...

15 68” METAL AND GLASS TV STAND www.insigniaproducts.com Step 11 - Optional: Install the anti-tipping restraint hardware • Instructions are included in the bag containing the hardware. You’ll need: Phillips screwdriver Drill NS-MG1205-C_14-0264_MAN_V1_ENG.fm Page 15 Wednesday, April 30, 2014 3:29 PM

16 68” METAL AND GLASS TV STAND www.insigniaproducts.com CARE AND MAINTENANCE Glass • Use a commercial liquid glass cleaner and a soft cloth. • Do not use harsh powders or any other abrasive substances as they will scratch the glass. WARNING Please use your furniture correctly and safely. Improper u...

17 68” METAL AND GLASS TV STAND www.insigniaproducts.com ONE-YEAR LIMITED WARRANTY - INSIGNIA Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original...