Ingersoll Rand PD07P-X-X - Manual
Ingersoll Rand PD07P-X-X – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – OPERATING AND SAFETY PRECAUTIONS
- Page 3 – OPERATING INSTRUCTIONS; EXCESSIVE AIR PRESSURE. Can cause pump
- Page 4 – COMMON PARTS; TYPICAL CROSS SECTION; Figure 2
- Page 5 – PTFE; Torque Sequence; Figure 3
- Page 6 – Indicates parts included in 637428 air section repair kit.; GENERAL SERVICE NOTES:; AIR MOTOR PARTS LIST
- Page 7 – MAJOR VALVE DISASSEMBLY
- Page 8 – TROUBLE SHOOTING; Product discharged from air exhaust.; DIMENSIONAL DATA; Figure 5; DIMENSIONS
OPERATOR’S MANUAL
PD07P-X-X
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
RELEASED:
2-16-07
REVISED:
6-24-13
(REV.
G
)
3/4" DIAPHRAGM PUMP
1:1 RATIO (NON-METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
(800)
y
FAX (800)
© 201
3
CCN
15275175
SERVICE KITS
Refer to Model Description Chart to match the pump mate-
rial options.
637427-XX for fl uid section repair (see page 4).
637428 for air section repair (see page 6).
PUMP DATA
Models
. . . . . . . . . . . . . see Model Description Chart for “-XXX”
Pump Type
. . . . . . . . . Air Operated Double Diaphragm
Material
. . . . . . . . . . . . see Model Description Chart
Weight
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.61 lbs (2.54 kgs)
Maximum Air Inlet Pressure
. . . . . . . . 100 p.s.i.g. (6.9 bar)
Maximum Material Inlet Pressure
. . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure
. . . . . . . . . . 100 p.s.i.g. (6.9 bar)
Air Consumption
@ 40 p.s.i. . . . . . . . 1 c.f.m. / gallon (approx.)
Maximum Flow Rate
(fl ooded inlet)
. . . 14.8 g.p.m. (56.0 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g.
. 0.032 gal. (0.12 lit.)
Maximum Particle Size
. . . . . . . . . . . . . 3/32” dia. (2.4 mm)
Maximum Temperature Limits (diaphragm / ball / seat
material)
Hytrel® . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 66° C)
Polypropylene . . . . . . . . . . . . 35° to 175° F (2° to 79° C)
Santoprene® . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)
PTFE . . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)
Dimensional Data
. . . . . . . . . . . . . . . . . . . see page 8
Noise Level
@ 70 p.s.i., 60 c.p.m. . . . . . . 75.0 db(A)
c
c
The pump sound pressure levels published here have been updated to
an Equivalent Continuous Sound Level (L
Aeq
) to meet the intent of ANSI
S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or
the factory if you have questions concerning availability.
MODEL DESCRIPTION CHART
PD07P - X P S - P X X
Center Section Material
P - Polypropylene
Fluid Connection
A - 3/4 - 14 N.P.T.F. - 1
B - Rp 3/4 (3/4 - 14 BSP, parallel)
Ball Material
A - Santoprene
C - Hytrel
T - PTFE
Fluid Section Service Kit Selection
EXAMPLE: Model #PD07P-APS-PAA
Fluid Section Service Kit # 637427-AA
PD07P - XPS - P X X
Ball
Diaphragm
637427 - X X
Fluid Cap & Manifold Material
P - Polypropylene
Diaphragm Material
A - Santoprene
C - Hytrel
T - PTFE / Santoprene
Seat Material
P - Polypropylene
Hardware Material
S - Stainless Steel
Figure 1
ZZZLQJHUVROOUDQGSURGXFWVFRP
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 of 8 PD07P-X-X (en) WARNING EXCESSIVE AIR PRESSURE. Can cause per- sonal injury, pump damage or property damage.Do not exceed the maximum inlet air pressure as stated on the pump model plate.Be sure material hoses and other components are able to withstand fl uid pressures developed by this p...
PD07P-X-X (en) Page 3 of 8 y Hytrel® is registered trademarks of the DuPont Company y Santoprene® is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. y y Lubriplate® is a registered trademark of Lubriplate Division (Fiske Brothers Refi ning Company) y ARO® is ...
Page 4 of 8 PD07P-X-X (en) PARTS LIST / PD07P-X-X FLUID SECTION 637427-XX Fluid Section Service Kits include: Balls (see Ball Option, refer to -XX in chart below), Diaphragms (see Diaphragm Op- tion, refer to -XX in chart below), and item 19 (listed below) plus items 144, 174 and 94276 Lubriplate®...
