Ingersoll Rand 150BMG - Manual

Page 2 - RH; MODEL CODING; NOTICE

2 03524832_ed12 Product Safety Information Intended Use: The 150BMG Series Air starters are intended for use in starting reciprocating internal combustion engines. These starters are designed to be operated from a remote location after proper installation on the engine requiring starting. For Additi...

Page 3 - Mounting the Air Starter; Barring Over the Engine

03524832_ed12 3 causing corrosion and icing in cold weather. If either of these conditions exist, the starter will not operate. After all connections have been made, check each joint with a soap bubble test, 7. Installation of a “glad hand” for emergency repressurizing the system is recommended. To ...

Page 5 - 50BMG Series Air and Gas Starters Dimensional Drawing

03524832_ed12 5 150BMG Series Air and Gas Starters Dimensional Drawing 3/8 -18 NPT L ube co nnec tion 18.03 12.34 3.56 3.25 2.00 Cove r Mo to r Housing 8.69 2.46 Gear C ase Driv e Housing 3.25 4.44 72˚30’ 120˚ 120˚ R 2.359 R ight Hand or Clock wise Rotation L e ft Hand or C o unt er Clock wise Rotat...

Page 6 - 50BMG Series Air and Gas Starters Typical Installation; rq

6 03524832_ed12 150BMG Series Air and Gas Starters Typical Installation T o rq ue (lb -f t) P o w e r (HP) F lo w (SCF M) Series 150BM and 150BMG Performance Curves 0 20 40 60 80 100 120 25 20 15 10 300 600 900 1200 5 0 0 500 1000 1500 Speed (RPM) 2000 2500 3000 Starter 3BM, 5BM 0-30’ # 12 (3/4 “) S...

Page 7 - 50BMG Series Air and Gas Starters Sectional View; ir Str

03524832_ed12 7 150BMG Series Air and Gas Starters Sectional View 8 9 2 2 5 6 7 10 55 40 14 52 A ir Str a iner 53 51 54 55 39 38 37 36 35 56 34 33 32 1 11 30 31 27 24 23 22 21 19 20 15 19A 18 18A 16 13 12 (Dwg. TPA61-7)

Page 8 - 50BMG Series Air and Gas Starters Exploded View

8 03524832_ed12 150BMG Series Air and Gas Starters Exploded View 2 5 18A 15 56 16 18 19A 19 34 21 33 22 23 24 27 30 20 32 31 6 2 1 55 7 9 8 10 13 40 11 39 37 36 35 12 14 55 38 (Dwg. TPA683-2)

Page 10 - WARNING

10 03524832_ed12 Maintenance Section WARNING Always wear eye protection when operating or performing any maintenance on this Starter.Always turn off the air or Gas supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this Starter or before performing an...

Page 11 - Inspection of Parts; Assembly; Ingersoll Rand No. 50 Oil before installation.; Assembly of Motor

03524832_ed12 11 Inspection of Parts 1. Discard all O-rings and gaskets. These should not be reused.2. Check all grease seals. If they appear worn or distorted, remove them from their parent member and discard. NOTICE Discard any grease seal that was removed during disassembly of the starter. 3. Che...

Page 12 - Ingersoll Rand No. 130 Grease between the-rollers of; Assembly of Drive Housing; Testing the Starter

12 03524832_ed12 12. Set the Front End Plate (39), crescent grooved side fi rst, onto the Cylinder so that the Cylinder Dowel passes through the dowel hole in the End Plate. Make sure that all notches and ports are in alignment. 13. Install the Front Rotor Bearing (37) onto the splined shaft of the ...

Page 13 - Parts and Maintenance; Troubleshooting Guide; Trouble

03524832_ed12 13 Parts and Maintenance NOTICE The use of other than genuine Ingersoll Rand replacement parts may result in safety hazards, decreased starter performance, and increased maintenance, and may invalidate all warranties. Ingersoll Rand is not responsible for customer modifi cation of star...

Page 16 - Ingersoll Rand

Ingersoll Rand 150BMG - Manual

Table of Contents:

Summary

Other Ingersoll Rand Models