Page 3 - ii; Important Safety Information; Symbols Used; button on the remote control to open the; DISPLAY; lens when the lamp is on.
IN3118HD User’s Manual — ii — Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future refere...
Page 4 - Preface; Projector Installation Notice; Place the projector in a horizontal position; Power Safety; Only use the supplied power cord.
Preface Projector Installation Notice ¾ Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically. ¾ Allow at le...
Page 5 - Replacing the Lamp; Replacing the Projection Lamp; Cleaning the Projector; Regulatory Warnings; Regulatory Compliance; Important Recycle Instructions:; About this Manual; iv
IN3118HD User’s Manual Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 33 for clear and safe instructions for this procedure. Before replacing the lamp: ¾ Unplug the power cord. ¾ Allow the lamp to cool for about one hour. Cleanin...
Page 6 - Table of Contents
Preface – v – Table of Contents GETTING STARTED ........................................................................................................................................................... 1 P ACKING C HECKLIST .............................................................................
Page 7 - REGULATORY COMPLIANCE; FCC
IN3118HD User’s Manual — vi — P ROJECTION D ISTANCE VS . P ROJECTION S IZE .................................................................................................................... 43 Projection Distance and Size Table .........................................................................
Page 8 - DLP Projector – User’s Manual; ETTING; Packing Checklist; DLP; VGA
DLP Projector – User’s Manual – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP P ROJECTOR R EMOTE CONTROL (B ATTERIES NOT INCLUDED ) C ARRY C ASE CD-ROM (T HIS U SER ’ S MANUAL ) VGA CABLE P OWER CORD ( VARIES PER COUNTRY )...
Page 9 - Views of Projector Parts
IN3118HD User’s Manual Views of Projector Parts Front-right View 1 3 4 5 6 7 2 I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Elevator button Push to release elevator foot 2. Elevator foot Adjusts level of projector 10 3. Lens Projection Lens 4. IR receiver Receives the remote control IR signal 6 5. Focus...
Page 10 - Error code; LED Error Messages
DLP Projector – User’s Manual Top view—On-screen Display (OSD) buttons and LEDs Source Menu Enter Re-sync 11 10 12 12 4 56 3 7 8 9 I TEM L ABEL D ESCRIPTION S EE PAGE : Solid Green Power On / Standby 1. Power LED Off Power Off (AC Off) Solid Red The lamp is powered on. 2. Lamp LED Flashing Red The l...
Page 11 - Rear view
IN3118HD User’s Manual Rear view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. AC IN Connect the POWER CABLE 9 2. (USB) Connect the USB CABLE from a computer (used for presentation slide control with the projector remote) 3. S-VIDEO IN Connect the S-VIDEO CABLE from a video device 4. VIDEO IN Connect the...
Page 12 - Bottom view
DLP Projector – User’s Manual Bottom view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Leveling foot Rotate leveling foot to adjust angle position. 10 2. Ceiling support holes Only use with an InFocus ceiling mount system (p/n PRJ-MNT-UNIV). See your InFocus dealer or go to www.infocusstore.com . 3. Ele...
Page 13 - Remote Control Parts
IN3118HD User’s Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the ...
Page 14 - Adjust overscan
DLP Projector – User’s Manual – 7 – I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Power ON Turn the projector on 9 2. LED indicator Only lights when the remote keys are pressed 3. Display Mode Choose a suitable preset mode for usage environment 4. Contrast Display the Contrast setting bar and use the rig...
Page 15 - Inserting the Remote Control Batteries
IN3118HD User’s Manual – 8 – S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the di-rection of the arrow. 2. Insert the batteries (not included) as shown in the illustration. 3. Replace the cover. Caution: 1. Only use AA ba...
Page 16 - Starting and Shutting down the Projector; POWER
DLP Projector – User’s Manual Starting and Shutting down the Projector 1. Connect the power cord to the pro-jector. Connect the other end to a wall outlet. The POWER LED will be on. 2. Turn on the connected devices. 3. Ensure the POWER LED dis- plays a solid green. Then press the Power ON button on ...
Page 17 - Adjusting the Projector Level; The projector table or stand should be level and sturdy.
IN3118HD User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. • Remove and discard the foam spacer on the rear leveling foot...
Page 18 - Adjusting the Zoom ring, Focus and Keystone; Use the; Zoom; Focus; control; KEYSTONE
DLP Projector – User’s Manual Adjusting the Zoom ring, Focus and Keystone 1. Use the Zoom control (on the projector only) to resize the projected image and screen size B . 2. Use the Focus control (on the projector only) to sharpen the pro-jected image A . 3. Use the KEYSTONE buttons (on the projec-...
Page 19 - Adjusting the Volume; Press the; Volume; MUTE; button
IN3118HD User’s Manual Adjusting the Volume 1. Press the Volume but- tons (on the projector or the remote control). The volume control appears on the display. 2. Use the Vol +/- buttons (on the projector or the remote control). 3. Press the MUTE button to turn off the audio (This feature is avail-ab...
Page 20 - CREEN; OSD Menu Controls; MENU
DLP Projector – User’s Manual – 13 – O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the projector keypad to navigate and make ...
Page 21 - Setting the OSD Language
IN3118HD User’s Manual Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic . 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the lan...
Page 22 - OSD Menu Overview
DLP Projector – User’s Manual OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting. PICTURE>> Basic Display Mode Brightness Tint Color Contrast Sharpness Movie/Bright/Normal/User 1/User 2/User 3 Flesh Tone PICTURE>> Advanced Nois...
Page 24 - HSG; Auto
DLP Projector – User’s Manual PICTURE>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu. Press ◄► to change values for settings. I...
Page 26 - DISPLAY Menu; PC Detail Adjustment
DLP Projector – User’s Manual DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings. I TEM D ESCRIPTION Aspect Ratio Press the cursor ...
Page 27 - AUTO IMAGE
IN3118HD User’s Manual PC Detail Adjustment Press the ENTER/SELECT button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (ana-log RGB) is selected. I TEM D ESCRIPTION Auto Press the RE-SYNC button on the ...
Page 28 - Menu
DLP Projector – User’s Manual SETUP>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu. Press ◄► to change values for settings. I TEM D ESCRIPTI...
Page 29 - Menu Settings; Center
IN3118HD User’s Manual Menu Settings Press the ENTER/SELECT button to enter the Menu Settings sub menu. I TEM D ESCRIPTION Menu Position Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center / Bottom-Left/ Bottom-Right. Menu Display Time Press the ◄► buttons to set the ...
Page 30 - Lan Control Settings; Network State
DLP Projector – User’s Manual Lan Control Settings Press the ENTER/SELECT button to enter the Lan Control Settings sub menu. I TEM D ESCRIPTION Control By Press the ◄► buttons to select projector remote command control. Selecting RJ45 enables RJ45 control and disables the RS232 port. Selecting RS232...
Page 33 - Preparing Email Alerts; Alert Mail Settings
IN3118HD User’s Manual Preparing Email Alerts 1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex- ample, Microsoft Internet Explorer v6.01/v8.0). 2. From the Homepage of LAN/RJ45, click Alert Mail Settings . 3. By default, these input boxes in Alert Mail Setti...
Page 34 - The; From; is a required field.; Group; and; Name
DLP Projector – User’s Manual The From field is the sender’s email address (for example, the projector administrator). This is a required field. Select the alert conditions by checking the desired boxes. Note: Fill in all fields as specified. Select the desired alert condition and click Submit to co...
Page 35 - Audio
IN3118HD User’s Manual SETUP>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Ad- vanced menu. I TEM D ESCRIPTION Audio Press the ENTER/SELECT butt...
Page 36 - Lamp
DLP Projector – User’s Manual Audio Press the ENTER/SELECT button to enter the Audio sub menu. I TEM D ESCRIPTION Volume Press the ◄► buttons to adjust the audio Volume. Treble Press the ◄► buttons to adjust the audio Treble. Bass Press the ◄► buttons to adjust the audio Bass. Mute Press the ◄► butt...
Page 37 - HDMI; Closed Caption
IN3118HD User’s Manual HDMI Press the ENTER/SELECT button to enter the HDMI sub menu. I TEM D ESCRIPTION HDMI Format Press the ◄► buttons to select from three HDMI display formats: Auto/ PC signal/ Video signal. HDMI Amplifier Gain Press the ◄► buttons to adjust HDMI Amplifier Gain. Use this feature...
Page 38 - Presentation Timer
DLP Projector – User’s Manual Presentation Timer The Presentation Timer function can indicate the presentation time on the screen to help you achieve better time management when giving presentations. I TEM D ESCRIPTION Timer Press the cursor ◄► button to enable or disable presentation timer. Timer P...
Page 39 - button to open the; OSD; menu. Press the cursor; STATUS Menu
IN3118HD User’s Manual STATUS Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the STATUS Menu . I TEM D ESCRIPTION Source Displays the activated input source. Resolution Displays the native resolution of input source. Lamp Hour Displays the number of hours the ...
Page 40 - AINTENANCE AND; • Unplug the power cord before replacing the lamp.
DLP Projector – User’s Manual – 33 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. Be sure to use the InFocus lamp module de-signed for this projector. You can order new lamps from www.infocusstore.com (in select areas), your retai...
Page 41 - Lift the module handle up.
IN3118HD User’s Manual 2. Remove the single screw on the lamp compartment cover. 3. Remove the lamp com-partment cover. 4. Remove the three screws from the lamp module. 5. Lift the module handle up. – 34 –
Page 42 - Select
DLP Projector – User’s Manual 6. Pull firmly on the module handle to remove the lamp module. 7. Reverse steps 1 to 6 to in-stall the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place an...
Page 43 - Lightly wipe the lens in a circular motion.; Cleaning the Case; Refer to the following to clean the projector case.
IN3118HD User’s Manual – 36 – Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 60 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a da...
Page 44 - ROUBLESHOOTING; Common Problems and Solutions; Ensure the projector is turned on.; Tips for Troubleshooting
DLP Projector – User’s Manual – 37 – T ROUBLESHOOTING Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the proble...
Page 45 - LED; Image Problems; Problem: No image appears on the screen
IN3118HD User’s Manual – 38 – LED Error Messages E RROR C ODE M ESSAGES P OWER LED L AMP / R EADY LED T EMP LED Powered on Solid Green Solid Red OFF Powering up Solid Green Flashing Red OFF Cooling down Solid Green Flashing Red OFF Over Temperature OFF OFF Solid Red Thermal Break Sensor error Flashe...
Page 46 - Problem: The image is streaked; Lamp Problems; Problem: There is no light from the projector; Remote Control Problems; Problem: The projector does not respond to the remote control
DLP Projector – User’s Manual – 39 – Problem: The image is streaked 1. Set the Frequency and Tracking settings on the Display >> PC Detail Adjustment menu of the OSD to the default settings. 2. To ensure the problem is not caused by a connected PC’s video card, connect to another computer. Pro...
Page 47 - Audio Problems; Problem: There is no sound; Having the Projector Serviced; If you are unable to solve the problem
IN3118HD User’s Manual – 40 – Audio Problems Problem: There is no sound 1. Adjust the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced. Problem: The sound i...
Page 48 - Q. How do I run HDMI cables longer than 10 meters?
DLP Projector – User’s Manual – 41 – HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High-Speed cables. ˙Standard (or “category 1”) HDMI cables have been tested ...
Page 49 - PECIFICATIONS; Specifications
IN3118HD User’s Manual – 42 – S PECIFICATIONS Specifications Model IN3118HD Display type TI DLP DMD 0.65” Native Resolution 1920 x 1080 Projection distance 1 meters ~ 10 meters ( 3.28 ft ~ 32.8 ft ) Projection screen size 23.67" ~ 284" ( 60cm ~ 721cm ) Projection lens Manual Focus/Manual Zoo...
Page 50 - Projection Distance vs. Projection Size
DLP Projector – User’s Manual Projection Distance vs. Projection Size Projection Distance and Size Table 16:9 SCREEN PROJECTION DISTANCE DIAGONAL WIDTH HEIGHT INCH MM MM ( INCH ) MM ( INCH ) MIN LENGTH (WITH MAX ZOOM) AVERAGE MAX LENGTH (WITH MIN ZOOM) VERTICAL OFFSET (A) MM ( INCH ) 30 762 664(26) ...
Page 51 - Timing Mode Table; NTSC —
IN3118HD User’s Manual – 44 – Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO VGA ( ANALOG ) HDMI ( DIGITAL ) NTSC — 15.734 6...
Page 52 - HDTV; O: Frequency supported
DLP Projector – User’s Manual – 45 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO VGA ( ANALOG ) HDMI ( DIGITAL ) 720p 37.5 50.0 — O O 720p 45.0 60.0 — O O 1080i 33.8 60.0 — O O 1080i 28.1 50.0 — O O 1080p 67.5 60.0 — O O HDTV 1080p 56.3 50.0 — O O O: Frequency supported ...
Page 53 - Projector Dimensions
Page 54 - EGULATORY; FCC Warning; This class B digital apparatus complies with Canadian ICES-003.; WEEE
DLP Projector – User’s Manual – 47 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pur-suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when...
