Icom iPW1 - Manual
Icom iPW1 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PRECAUTION
- Page 3 – INSTALLATION AND CONNECTIONS 5–10; Initial settings for CI-V remote control operation; EXPLICIT DEFINITIONS; ii; WORD; Equipment damage may occur.; NOTE
- Page 4 – PANEL DESCRIPTION; Front panel and remote controller
- Page 5 – - While operating in the 50 MHz band, the antenna; BAND INDICATORS
- Page 6 – Rear panel; , etc. These sockets can be separated by the; Adjust the ALC levels.; DO NOT; Cut off the AC input when over current occurs.; GROUND TERMINAL
- Page 7 – DESCRIPTION; Sets the connected exciter number.; fied band antenna connectors is connected.
- Page 8 – INSTALLATION AND CONNECTIONS; Unpacking; The supplied cable ties (; OPC-853 AC cable with line filter; *Use the appropriate AC plug if required.
- Page 9 – PL-259 CONNECTOR INSTALLATION; in; Antenna SWR
- Page 10 – System interconnections; be sure to connect the
- Page 12 – • Using 1 Icom and 1 non-Icom exciters; Relay; Relay
- Page 13 – (1) Supply the antenna selector power to the; - The antenna selector functions even when the IC-; • Jumper location of linear amplifier
- Page 14 – Separating the remote controller; JACK unit
- Page 15 – OPERATION; Setting the ALC levels; Resetting CLEARS all programmed set-; resetting is complete.; Final FETs may be damaged if; - Select a band which uses a well-matched 50; Output power; When first applying power
- Page 16 – Setting the Icom exciters; use the “AUTO” baud rate for CI-V; - Refer to the instruction manual for details.; DO; set to “AUTO” baud rate.; quencies are synchronized.; DO NOT USE; • Connect the supplied remote cable between the IC-; When using 1 Icom exciter; Continue to the next page...; Programming the CI-V address
- Page 17 – Turn the power OFF when you are going to; NEVER TURN THE POWER OFF; Rotate the exciter’s dial until the LED [INPUT; • When selecting the different baud rate for each exciter,
- Page 19 – The band information is not updated while; - If the temperature meter reading is in the red “HOT”; Band memory; Operation
- Page 20 – Protection circuit; Item
- Page 21 – MAINTENANCE; Troubleshooting; PROBLEM
- Page 22 – SPECIFICATIONS; General; MODE; kW PEP; DECLARATION
- Page 23 – INSTALLATION NOTES; • Typical amateur radio installation; Watts; Forward clearance, EIRP by frequency band; This warning symbol indicates that this
iPW1
iPW1EURO
HF/50 MHz ALL BAND
1 kW LINEAR AMPLIFIER
INSTRUCTION MANUAL
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
R WARNING HIGH VOLTAGE! NEVER attach an antenna or internal antenna connector dur-ing transmission. This may result in an electricalshock or burn. R WARNING! NEVER carry the linear amplifier by yourself. At least two persons must carry the linearamplifier since it weights approx. 25 kg (55 lb). R WA...
IMPORTANT ...................................................... iPRECAUTION ................................................... iEXPLICIT DEFINITIONS ................................. iiTABLE OF CONTENTS .................................. iiSUPPLIED ACCESSORIES ............................ ii 1 PAN...
1 1 PANEL DESCRIPTION ■ Front panel and remote controller 0 100 250 500 1K 1.5K 0 TEMP ALC ALC ad j SWR 0 1 1.5 2 3 10 20 30 40 50 60 V D HOT I D Po 10 20 30 40 50 60 W A METER-1 METER-2 P o TEMP I D V D ALC SWR DOWN 1.8 3.5 7 10 14 18 21 24 28 50 UP ANT INPUT AUTO TRANSMIT TUNER AMP/PROTECT POWER V...
