Icom IC-F110 - Manual - manualsarea.com

Page 3 - TABLE OF CONTENTS

ii DO NOT use or place the transceiver in areas with tem- peratures below –30°C (–22°F) or above +60°C (+140°F), orin areas subject to direct sunlight, such as the dashboard. AVOID operating the transceiver without running the vehi- cle’s engine. The vehicle’s battery will quickly run out if thetran...

Page 4 - PANEL DESCRIPTION; Front panel; AF VOLUME CONTROL KNOB; FUNCTION DISPLAY

1 1 PANEL DESCRIPTION y t r q w e ■ Front panel q AF VOLUME CONTROL KNOB Rotate the knob to adjust the audio output level. • Minimum audio level is pre-programmed. w FUNCTION DISPLAY Displays a variety of information, such as an operatingchannel number/name, 5-tone code, DTMF numbers andaudible cond...

Page 5 - Function display

2 1 PANEL DESCRIPTION t DEALER-PROGRAMMABLE KEYS [P0] to [P3] Desired functions can be programmed independently byyour dealer. y MICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF micro-phone for SmarTrunk II TM operation here. NEVER connect non-specified microphones. The pin assi...

Page 6 - ALPHANUMERIC DISPLAY; Programmable function keys

3 1 PANEL DESCRIPTION u 2/5TONE INDICATOR Appears when the specified 2/5-tone call is received. i ALPHANUMERIC DISPLAY Displays the CH number, 5-tone indication, DTMF num-bers, Audible indication, etc. NOTE: When the alphanumeric display blinks and trans- mitting becomes impossible, check that the D...

Page 10 - OPERATION; Turning power ON

7 2 OPERATION ■ Turning power ON q Push [ ] to turn the power ON. w If the transceiver is programmed for a start up passcode,input the digit codes as directed by your dealer. • The keys in the table below can be used for password input:• The transceiver detects numbers in the same block as identical...

Page 11 - Receiving and transmitting; Transmitting notes; • Transmit inhibit function

8 2 OPERATION ■ Receiving and transmitting RECEIVING: q Push [ ] to turn the power ON. w Push [ ] and [ ] to select a channel. e When receiving a call, adjust the audio output level to acomfortable listening level. TRANSMITTING: r Take the microphone off hook. • 2-tone, 5-tone mute may be released. ...

Page 12 - TX code channel selection; TX code number selection; Scrambler function

9 2 OPERATION D TX code channel selection If the transceiver has a [TX CH] key, the display can be tog- gled between the operating channel number (or name) andTX code channel number (or name). When the TX codechannel number (or name) is displayed, the [ ] / [ ] keys select the TX code channel. To se...

Page 13 - User set mode

10 2 OPERATION D User set mode User set mode is accessed at power ON and allows you toset seldom-changed settings. In this case you can “cus-tomize” transceiver operation to suit your preferences andoperating style. Entering the user set mode: q While pushing and holding [ ] and [ ] , push [POWER] t...

Page 14 - OPTIONAL SmarTrunk IITM OPERATION; SmarTrunk IITM operation; Placing a telephone call

11 3 OPTIONAL SmarTrunk II™ OPERATION ■ SmarTrunk II™ and conventional modes This transceiver is capable of SmarTrunk II™ functions. The optional UT-105 allows communication in conventionalchannels or SmarTrunk II™ channels. Select a channel bankfor SmarTrunk II™ before trunking operation. • Push [ ...

Page 16 - CONNECTION AND MAINTENANCE; NEVER; C A U T I O N ! N E V E R; Rear panel and connection

13 4 CONNECTION AND MAINTENANCE Optional speaker (SP-22) Optional cable (OPC-617) Antenna NEVER connect to a 24 V battery. + red: black: 12VBattery Solder Crimp NOTE: Use the terminals as s h o w n b e l o w f o r t h e c a b l e connections. R C A U T I O N ! N E V E R r e- m o v e t h e f u s e - ...

Page 17 - CONNECTION AND MAINTENANCE; Supplied Accessories

14 4 CONNECTION AND MAINTENANCE q ANTENNA CONNECTOR Connects to an antenna. Contact your dealer about an-tenna selection and placement. w MICROPHONE HANGER Connect the supplied microphone hanger to the vehicle’sground for microphone on/off hook functions. (See p. 2) e DC POWER RECEPTACLE Connects to...

Page 18 - Mounting the transceiver

15 4 CONNECTION AND MAINTENANCE ■ Mounting the transceiver The universal mounting bracket supplied with your transceiv-er allows overhead mounting.• Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg. Flat washer Spring washer When usingse...

Page 19 - Optional OPC-617 installation

16 4 CONNECTION AND MAINTENANCE ■ Optional UT-109 or UT-110installation q Turn the power OFF, then disconnect the DC power cable. w Unscrew the 4 cover screws, then remove the bottomcover. e Cut the pattern on the PCB at the TX mic circuit (MIC) andRX AF circuit (DISC) as shown below. r Install the ...

Page 20 - Cleaning; AVOID

17 4 CONNECTION AND MAINTENANCE ■ Antenna A key element in the performance of any communication sys-tem is an antenna. Contact your dealer about antennas andthe best places to mount them. ■ Fuse replacement A fuse is installed in the supplied DC power cable. If a fuseblows or the transceiver stops f...

Page 21 - OPTIONS; SP-22 EXTERNAL SPEAKER; Logic Board; UT-108 DTMF DECODER UNIT; UT-111 TRUNKING BOARD

18 5 OPTIONS SP-22 EXTERNAL SPEAKER Compact and easy-to-install.Input impedance : 4 Ω Max. input power : 5 W HM-100TN DTMF microphone. SM-25 Desktop microphone. UT-105 SmarTrunk II TM Logic Board Provides SmarTrunk II TM capabilities. UT-108 DTMF DECODER UNIT Provides pager and code squelch capabili...

Page 22 - MEMO

MEMO IC-F110_F210_GEN.qxd 02.12.11 4:25 PM Page 19 (1,1)