Page 3 - ii; INTRODUCTION; IMPOR; IMPORTANT
ii INTRODUCTION IMPOR T ANT IMPORTANT When connecting the AP-12 to a bridging type modem (or inbridging mode) directly, a global IP address may be assigned tothe AP-12 from the modem, according to the modem settings.When a global IP address is assigned to the AP-12, an illegaloperator, such as a cra...
Page 4 - iii; TRADEMARK CREDITS; logo are registered trade-; FOREWORD
iii INTRODUCTION TRADEMARK CREDITS Icom, Icom Inc. and the logo are registered trade- marks of Icom Incorporated (Japan) in the Unitedstates, the United Kingdom, Germany, France, Spain,Russia and/or other countries.Windows is a registered trademark of MicrosoftCorporation in the United States and/or...
Page 5 - iv; FEATURES; Windows XP
iv INTRODUCTION FEATURES " " Up to 11 Mbps data transmission rate with automatic fallback function (11/5.5/2/1Mbps). " " The supplied utility software, [AP-12 Manager] allows you simple setup of the sys-tem with a step-by-step tutorial. Windows XP , Windows Me, Windows 98SE, Windows ...
Page 6 - void the user’s authority to operate this Access Point.; RF EXPOSURE SAFETY INFORMATION:; For CANADA only; AP; Tested to comply; FOR HOME OR OFFICE USE; FCC INFORMATION
v INTRODUCTION CAUTION: Changes or modifications not expressly approved by Icom Inc. could void the user’s authority to operate this Access Point. Class B digital device users;This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the F...
Page 7 - The following notational conventions are used in this manual:; - Windows 98 SE represents the Windows 98 Second Edition.; Notational Conventions; Do not use it for any other devices.
vi INTRODUCTION INTRODUCTION The following notational conventions are used in this manual: • The names of utilities, menus, windows, tabs, icons, text boxes, and check boxes are enclosed in square brackets ([ ]). • The names of command buttons within dialog boxes are enclosed in less-than and greate...
Page 8 - vii; ACCESSORIES; Supplied accessories
vii ACCESSORIES ■ Supplied accessories CD AC Adapter Leg Pad Fixing Sheet Patch cable 3 m (9.8 feet) Crossover cable 1 m (3.2 feet) Instruction Manual Registration Card Warranty Card AP-12 Main Unit AP-12 Attach to the bottom of the AP-12 to secure. Attach to the bottom of the AP-12 to secure.Remove...
Page 9 - viii; TABLE OF CONTENTS; ABLE OF CONTENTS; -1 Wireless functional modes
viii TABLE OF CONTENTS IMPORTANT ………………………………………………………………………………iiINTRODUCTION …………………………………………………………………………iiiACCESSORIES …………………………………………………………………………viiTABLE OF CONTENTS ………………………………………………………………viiiSAFETY PRECAUTIONS ………………………………………………………………x T ABLE OF CONTENTS Chapter 1 BEFORE INSTALLATION ……………………...
Page 10 - ix; Chapter 6; -8 Glossary ..................................................................70
ix TABLE OF CONTENTS Chapter 6 IP CONFIGURATION …………………………………51–56 6-1 For Windows XP ………………………………………………526-3 For Windows 98/98SE/Me ……………………………………546-2 For Windows 2000 ……………………………………………55 Chapter 7 REFERENCES …………………………………………57–71 7-1 Troubleshooting ………………………………………………58 7-2 Connecting the AP-12 a...
Page 11 - SAFETY PRECAUTIONS; listed under “; Be sure to read these precautions in order to use the AP-12 safely.; WARNING; Do not handle the unit with wet hands.
x SAFETY PRECAUTIONS SAFETY PRECAUTIONS • These precautions are intended to ensure that the access point is operated safely and correctly. Follow these instructions to avoid property damageand prevent personal injury to yourself (user) or others in the vicinity. • Before reading the rest of this man...
Page 12 - xi; CAUTION; Do not install the unit outdoors.
xi R CAUTION Failure to observe the precautions listed here couldresult in personal injury or property damage. ● Do not stand, sit, or place heavyobjects on the unit. Do not pinch theunit. Otherwise the unit may be damaged. ● When thunder and/or lightning occurnearby, disconnect the AC adapterfrom t...
Page 13 - xii; General Precautions; AC adapter
xii SAFETY PRECAUTIONS SAFETY PRECAUTIONS General Precautions ● The unit may malfunction if the connecting cables become disconnected or the connectionis unstable while the unit is in operation. Be sure all connectors are securely fastened anddo not touch them while the unit is in operation. ● Obser...
Page 15 - Chapter; BEFORE INSTALLATION; -1 Wireless functional modes ..................................................................2
Chapter 1 BEFORE INSTALLATION 1-1 Wireless functional modes …………………………………………………………2 ■ Access point mode …………………………………………………………………2 ■ Bridge mode A (Peer-to-Peer) ……………………………………………………2 ■ Bridge mode B (Client Mode) ……………………………………………………3 ■ Bridge mode C (Multi-site) …………………………………………………………3 ■ About a M...
Page 16 - the fixed IP address in the existing wired LAN.; Access point mode
2 BEFORE INSTALLATION 1 1-1 Wireless functional modes The AP-12 has 4 wireless functional modes.A functional mode can be selected with [AP-12 Manager].• The AP-12 obtains an IP address from the DHCP server automatically (default).• Bridge mode B does not support a DHCP client function.• Connect the ...
Page 17 - Bridge mode B; - To avoid communication speed slow; About a MAC address
3 1 1 BEFORE INSTALLATION ■ Bridge mode B (Client Mode) Connects wireless LAN terminal orthe AP-12 (2) connected LAN systemvia the AP-12 (1) in access pointmode.- Only the AP-12 works as the access point. - Register the desired AP-12’s MAC address, prior to communication,with AP-12 (2) when two or m...
Page 19 - To avoid falling; Ferrite core; -3 Accessory attachment
5 1 BEFORE INSTALLATION 1 ■ To avoid falling When mounting the AP-12 high on ashelf or the like, secure it using acable fastener or tie to prevent theAP-12 from accidental falling. ■ Leg pads/fixing sheet attachment Use the leg pads on the bottom ofthe AP-12 as below to place it on aflat surface Use...
Page 20 - To avoid interference
6 BEFORE INSTALLATION 1 AC adapter (supplied) 1-3 Accessory attachment (continued) ■ To avoid interference Do not detach the ferrite core from both the AC adapter and the Ethernet cable.Otherwise interference may occur when you use these items without the ferritecore. D D AC adapter D D Ethernet cab...
Page 21 - -4 Installation location; Installation precautions; Examples of recommended installation; (Transmission range and speed may decrease)
7 1 BEFORE INSTALLATION 1 1-4 Installation location The transmission range and speed may change according to the installation location.Installing the AP-12 in wide, open air with clear line of sight (example; a high place)is recommended.Approximate operating range at 11 Mbps speed is 30 m (98 ft) fo...
Page 22 - -5 About the Ethernet card; according to the slot type.; Desktop PC; Expansion slot; Ethernet card
8 1 BEFORE INSTALLATION 1-5 About the Ethernet card An Ethernet port is necessary in your PC for set up.Check that an Ethernet port is available with your PC before setting up.• If no Ethernet port is available, purchase a suitable Ethernet card separately according to the slot type. ■ Desktop PC In...
Page 23 - OBTAINING AN IP ADDRESS
Chapter 2 OBTAINING AN IP ADDRESS FROM THE DHCP SERVER 2-1 Connecting to a LAN ………………………………………………………………102-2 Installing [AP-12 Manager] ………………………………………………………112-3 Starting [AP-12 Manager] …………………………………………………………13 ■ [AP-12 Manager] Settings Screen ………………………………………………14 This chapter describes setting i...
Page 24 - OBTAINING AN IP ADDRESS FROM THE DHCP SERVER; -1 Connecting to a LAN; Connect the AP-12 and LAN with the supplied patch cable.; About DHCP server detection
10 OBTAINING AN IP ADDRESS FROM THE DHCP SERVER 2 2-1 Connecting to a LAN This section enables a DHCP server to assigns an IP address automatically. [Procedure] q Connect the AP-12 and LAN with the supplied patch cable. w Connect the AC adapter to the AC outlet to turn the AP-12 power ON. • POWER in...
Page 25 - Click; administrator; Quit all applications when Windows is running.
11 2 OBTAINING AN IP ADDRESS FROM THE DHCP SERVER 2 2-2 Installing [AP-12 Manager] t Verify the directory in which you want to install to, then click <Next>. • Click <…> and select the desired directory, if necessary. Click Click When installing into a Windows XP or Windows 2000 environm...
Page 26 - • The installation is now completed.
12 OBTAINING AN IP ADDRESS FROM THE DHCP SERVER 2 2-2 Installing [AP-12 Manager] (continued) y When the dialog “Create new directory?” appears, click <OK>. u Click <Install>. i Click <Finish>. • The installation is now completed. o Click <Exit> to close the main menu. Click C...
Page 27 - Click the desired access point name and then click .; Verify
13 2 OBTAINING AN IP ADDRESS FROM THE DHCP SERVER 2 e Click the desired access point name and then click <Connect>. • [AP-12 Manager] Setting screen (p. 14) appears on the screen. 2-3 Starting [AP-12 Manager] This section describes about the verification of the IP address obtained, using the[A...
Page 28 - to
14 OBTAINING AN IP ADDRESS FROM THE DHCP SERVER 2 2-3 Starting [AP-12 Manager] (continued) ■ [AP-12 Manager] Setting Screen After installing [AP-12 Manager], the following screen appears first. q to r are common buttons in the [AP-12 Manager] screen. To exit [AP-12 Manager] Move the cursor on the ic...
Page 29 - FIXED IP ADDRESS
Chapter 3 FIXED IP ADDRESS SETTING 3-1 Connecting to the PC ………………………………………………………………163-2 Using [Easy Setting Wizard] ……………………………………………………17 3-3 Installing [AP-12 Manager] ………………………………………………………253-4 Starting [AP-12 Manager] …………………………………………………………27 ■ [AP-12 Manager] Settings screen ……………………………………………...
Page 30 - FIXED IP ADDRESS SETTING; -1 Connecting to the PC; Connect the AP-12 and the PC with the supplied crossover cable.; NOTE: DISCONNECT THE PC FROM THE EXISTING LAN.; Connect the supplied AC adapter to the AP-12 and an AC outlet.
16 FIXED IP ADDRESS SETTING 3 3-1 Connecting to the PC [Procedure] q Connect the AP-12 and the PC with the supplied crossover cable. • Use the supplied patch cable (3 m: 9.8 ft) when connecting the AP-12 and the PC via a HUB. NOTE: DISCONNECT THE PC FROM THE EXISTING LAN. When the PC is connected to...
Page 31 - • When a new network is built, the IP
17 3 3-2 Using [Easy Setting Wizard] Changing the PC’s IP address is necessary using [Easy Setting Wizard] when set-ting up the AP-12. [Easy Setting Wizard] is contained in the utility CD and it allowseasy setting for changing the IP address. [Procedure] q Quit all applications when Windows is runni...
Page 32 - When no access point is found:
18 FIXED IP ADDRESS SETTING 3 y Click the desired access point name you want to set up, then click <Next>. • The default IP address is [192.168.0.1]. However, once the AP-12 has been con- nected to a LAN with a DHCP server, a different IP address may be obtained. 3-2 Using [Easy Setting Wizard...
Page 33 - About IP Address
19 3 FIXED IP ADDRESS SETTING 3 u When the PC cannot access the AP-12 due to a network address differencebetween them, the following screen appears. Enter the desired unique host address for the PC, then click <Next>.• When the PC can access the AP-12, the screen described in step !2 appears. ...
Page 34 - • The PC will restart.
20 FIXED IP ADDRESS SETTING 3 o [Easy Setting Wizard] will restart automatically. • Click <Next>. Click 3-2 Using [Easy Setting Wizard] (continued) i Select [Restart Windows now] and click <Finish>. • The PC will restart. Click 2. Click 1. AP-12_USA 02.7.26 9:32 AM Page 20 (1,1)
Page 35 - Click the access point, selected in step
21 3 FIXED IP ADDRESS SETTING 3 !1 Click the access point, selected in step u , and click <Next>. • The default IP address of the AP-12 is “192.168.0.1”. !0 Click <Next>. Click Click 2. Click 1. AP-12_USA 02.7.26 9:32 AM Page 21 (1,1)
Page 36 - • The screen in step
22 FIXED IP ADDRESS SETTING 3 3-2 Using [Easy Setting Wizard] (continued) !2 Select [Use a fixed IP address] and click <Next>. • The screen in step !4 appears when [Use dynamic IP address alloc] is selected. !3 Enter the IP address and subnet mask for the AP-12. • The network part must be the ...
Page 37 - 2 and wireless LAN card is set.
23 3 FIXED IP ADDRESS SETTING 3 !4 Set the ESS ID, then click <Next>. The default ID (LG) is used in this example.• The AP-12 can communicate with the unit in which the same ESS ID as the AP- 12 and wireless LAN card is set. • Click <Next> without changing the ESS ID, if desired. !5 Set ...
Page 38 - • When the PC can be connected to the AP-12 in step; assigned in step
24 FIXED IP ADDRESS SETTING 3 3-2 Using [Easy Setting Wizard] (continued) !6 Click <Next> to apply the settings to the AP-12. !7 Click <Finish>. !8 When the dialog “Reboot now?” appears on the screen, click <Yes>. • When the PC can be connected to the AP-12 in step u , this dialog ...
Page 39 - istrator
25 3 FIXED IP ADDRESS SETTING 3 3-3 Installing [AP-12 Manager] This section describes the settings utility, [AP-12 Manager], installation. [Procedure] When installing into Windows XP or Windows 2000 environment, log on as the admin- istrator . q Quit all applications when Windows isrunning. w Insert...
Page 42 - Follow the steps
28 FIXED IP ADDRESS SETTING 3 3-4 Starting [AP-12 Manager] (continued) e When the error dialog “Cannot connect to the accesspoint” appears on the screen, each AP-12 and the PC’snetwork IP address may be different. In such a case,click <OK> and close the dialog. Then, exit [AP-12Manager]. To ex...
Page 45 - See Chapter 1
Chapter 4 AP-12 MANAGER 4-1 [AP-12 Manager] screen descriptions …………………………………………32 ■ Settings ……………………………………………………………………………32 ■ IP Configuration …………………………………………………………………36 ■ MAC security ………………………………………………………………………37 ■ Wep security ………………………………………………………………………38 ■ Show Station …………………………………………………………...
Page 46 - Settings; assigned to each device in the network.
32 AP-12 MANAGER 4 4-1 [AP-12 Manager] screen descriptions ■ Settings w q Click OK or Apply to register the con- tents of the setting. r e y t u i o Shows the AP-12’s MAC address.The address is also mentioned on the serial numberseal.• The MAC address cannot be changed.• The MAC address is a unique ...
Page 48 - Select the wireless LAN functional mode.; • Remote MAC Address; “Remote MAC Address” appears when; Bridge Mode; “Preferred Bssid” appears when; Bridge Mode B; Functional mode ...
34 AP-12 MANAGER 4 4-1 [AP-12 Manager] screen descriptions ■ Settings (continued) Select the wireless LAN functional mode. (default: Access Point) See Chapter 1-1 (p. 2) for details of each mode. The following items appear when you select BridgeMode A or B. • Remote MAC Address “Remote MAC Address” ...
Page 50 - IP Configuration
36 AP-12 MANAGER 4 4-1 [AP-12 Manager] screen descriptions (continued) ■ IP Configuration Set the IP address of the AP-12. Set the desired IP address, Subnet mask andGateway.• The default settings are; IP Address : 192.168.0.1 Subnet mask : 255.255.255.0Gateway : 0.0.0.0 • The end of Subnet Mask can...
Page 51 - MAC security; ” mark
37 4 AP-12 MANAGER 4 ■ MAC security Sets MAC address security function.This function can only be set when the access point mode or Bridge mode C isselected. Turns the MAC security ON and OFF. (“ ✓ ” mark appears when set to ON.) (default: OFF) When the Mac security is turned ON, the wirelessdevices ...
Page 52 - Wep Security; ” mark appears when the encryption is set to
38 AP-12 MANAGER 4 4-1 [AP-12 Manager] screen descriptions (continued) ■ Wep Security (Setting for data security.) Turn the WEP transmission data encryption ON andOFF, and select the encryption level from 64-bit and128-bit. (“ ✓ ” mark appears when the encryption is set to ON.) (default: OFF) • 64 b...
Page 53 - WEP Key Setting Examples– 64-bit encryption; Two-way communication
39 4 AP-12 MANAGER 4 Select the desired WEP key number for data encryp-tion. (default:1) The desired key number can be selected between theAP-12 and another AP-12 or terminal.A key, generated by the key generator, is displayed inthe text boxes. However, the desired keys in hexa-decimal numbers can b...
Page 54 - Show Station; Refresh ...............
40 AP-12 MANAGER 4 4-1 [AP-12 Manager] screen descriptions (continued) ■ Show Station Shows all MAC address for registered terminals during access point mode operation. Refresh …………… Renews the MAC address indication.• [AP-12 Manager] recognizes a terminal is still con- nected for 5 minutes (approx....
Page 55 - Version Information
41 4 AP-12 MANAGER 4 ■ Version Information Shows the version number for the [AP-12 Manager] and the firmware. (>>) links to Icom home page. AP-12_USA 02.7.26 9:32 AM Page 41 (1,1)
Page 56 - Options
42 AP-12 MANAGER 4 Turns the splash screen ON and OFF.The screen appears when starting up [AP-12Manager]. (default: /Display) Selects [AP-12 Manager] icon indicating type fromflashing or non-flashing. The icon flashes whenchecked (“ ✓ ” appears). (default: /Flash) Turns the password function ON and ...
Page 57 - -2 The default settings
43 4 4-2 The default settings The default settings of [AP-12 Manager] are shown below. ■ Settings • Mac address : The MAC address is described on the serial num- ber seal. (The setting in this field cannot bechanged.) • Name : AP-12 • Regulatory : FCC (The setting in this field cannot be changed.) •...
Page 59 - SETTING EXAMPLES; -1 Access point mode; Bridge mode A
Chapter 5 SETTING EXAMPLES This chapter describes the minimum setting requirements in each functional modewith a setting example. 5-1 Access point mode ………………………………………………………………46 5-2 Bridge mode A (Peer to Peer) ……………………………………………………47 5-3 Bridge mode B (Client Mode) ……………………………………………………48 5-4 Bridge...
Page 60 - SETTING EXAMPLE; • IP address of the PC should already be; Select “Infrustructure”.
46 Set the following items in [AP-12 Manager] Settings screen. (pgs. 33, 34)• ESS ID : Set the same ID as the wireless terminal. • Channel : Set the desired channel.- Set the channel at least four channels apart to avoid interference if another AP- 12(s), operating on an other channel(s), are within...
Page 61 - • IP address of the PC should; • Functional mode; ” appears) when communication is unstable.
47 5 SETTING EXAMPLE 5 5-2 Bridge mode A (Peer-to-Peer) Set the AP-12 and the PC asin the network shown at right. • IP address of the PC should already be set. (See Chapter2 or 3) • See Chapter 4 (p. 31) for [AP-12 Manager] details. Set the following items in [AP-12 Manager] Settings screen (pgs. 33...
Page 65 - IP CONFIGURATION
Chapter 6 IP CONFIGURATION This chapter describes about changing the PC’s IP address.Changing of the PC’s IP address is required when setting up a LAN used with theAP-12 with a fixed IP setting and a PC.The default IP address is used with the AP-12 (192.168.0.1) for the setting descrip-tion in this ...
Page 66 - Log on as the
52 IP CONFIGURATION 6 6-1 For Windows XP [Procedure] q Boot up the PC. • The log-on screen appears. w Log on as the administrator . e After the PC has booted up, click <Start> and select [Control Panel] from the[Settings] menu. r Click [Network and Internet Connections]. t Click [Network Conne...
Page 68 - The Ethernet card name] is displayed in the screen.
54 IP CONFIGURATION 6 6-2 For Windows 98/98SE/Me [Procedure] q Click <Start> and select [Control Panel] from the [Settings] menu.Click [Network]. w Verify that [TCP/IP −> The Ethernet card name] is displayed in the screen. Click [TCP/IP] then, [Properties]. Click 2. Click 1. Click 1. Enter ...
Page 69 - Administrator
55 6 6-3 For Windows 2000 [Procedure] q Start the PC. • The Window 2000 log-on screen appears. w Log on as the Administrator . e Click <Start> and select [Network and Dial-up Connections] from the [Settings]menu. Then, double click [Local Area Connection] icon which shows your Ethernet cardnam...
Page 71 - REFERENCES; -8 Glossary .......................................................................................70
Chapter 7 REFERENCES 7-1 Troubleshooting ……………………………………………………………………587-2 Connecting the AP-12 and HUB …………………………………………………607-3 Verifying the connection to the AP-12 …………………………………………607-4 Failure in searching for the AP-12 ………………………………………………617-5 IP address confirmation …………………………………………………………64 ■ Win...
Page 72 - PROGRAM
58 REFERENCES 7 7-1 Troubleshooting If your AP-12 seems to be malfunctioning, please check the following points beforesending it to a service center. NO power comesON. Television interfer-ence (TVI) orbroadcast interfer-ence (BCI) occurs. C o m m u n i c a t i o nwith the AP-12 hasfailed. Wired LAN ...
Page 74 - -3 Verifying the connection to the AP-12; There are 2 ways to connect the AP-12 and HUB; Connect to the Cross Port; Ping command example
60 REFERENCES 7 7-3 Verifying the connection to the AP-12 The IP packet received condition of the other PC can be easily checked by pingingwhen the IP address for each terminal is set correctly.Enter the following command in the MS-DOS window to verify by pinging. “ping xxx.xxx.xxx.xxx” Enter the de...
Page 76 - Enter the MAC address, described on the serial number seal.
62 REFERENCES 7 7-4 Failure in searching for the AP-12 (continued) r Enter the desired IP address for the AP-12. The network part must be the sameas the PC’s IP address. t Enter the MAC address, described on the serial number seal. y Turn the power OFF.After waiting a few seconds, turn the power ON ...
Page 77 - Set
63 7 REFERENCES 7 o Click <Search>. !1 Click [IP Configuration] and set the AP-12’s IP address as desired. !2 Click <OK> to register all the settings in the screen to the AP-12. !0 Select the AP-12, then click <Connect>. • [AP-12 Manager] Settings screen appears. Click Click 2. Cli...
Page 78 - -5 IP address confirmation; DHCP server by connecting the PC to the LAN.; • IP address assigned to the PC is displayed.
64 REFERENCES 7 7-5 IP address confirmation When the PC’s IP address, including network part, is unknown, refer to the followinginstructions for confirmation.- Reset the desired fixed IP address manually, or obtain an IP address from the DHCP server by connecting the PC to the LAN. ■ Windows XP [Pro...
Page 79 - Select; Confirm
65 7 REFERENCES 7 ■ Windows 98/98SE/Me [Procedure] q Click <Start> and select [Run]. w Enter “winipcfg” and push [Enter]. e Click [ ▼ ] and select the desired Ethernet card. • IP address assigned to the PC is displayed. Select 1. Confirm 2. ■ Windows 2000 [Procedure] q Click <Start> and ...
Page 80 - -6 Connection to the router type modem; The AP-12 cannot be connected to a bridging type modem directly.; Wireless terminal preparation; Prepare the PC to use the wireless LAN card.
66 REFERENCES 7 7-6 Connection to the router type modem This section describes the connection between a router type modem and the AP-12with the default setting.There are different types of modems available—bridging type and router type. IMPORTANT!: The AP-12 cannot be connected to a bridging type mo...
Page 81 - Connection to the router type modem; Connect the AC adaptor to turn the AP-12 power ON.; INTERNET; When communication has failed.
67 7 REFERENCES 7 D D Connection to the router type modem [Procedure] q Connect the AP-12 and the router type modem using the supplied patch cable. w Connect the AC adaptor to turn the AP-12 power ON. • The [POWER] indicator and the LAN indicator lights.• The [Wireless LAN] indicator flashes. * Chec...
Page 82 - With supplied AC adapter is 90 to 132 V AC
68 REFERENCES 7 7-7 Specifications • Input power : 7.5 V DC ±5% (Negative grounding) With supplied AC adapter is 90 to 132 V AC • Current drain : Transmit 400 mA (typical) Receive 350 mA (typical) • Operating temperature range : 0 to +55°C; +32 to +131°F • Dimensions : 100.0(W) × 30.5(H) × 70.0(D) m...
Page 86 - MEMO
