Page 3 - Specifications CD300
Specifications CD300 Page 2 Specifications and Limitations This dispenser is designed to dispense cubed ice only and to be installed and operated indoors, in acontrolled enviroment. Its minimum and maximum operating temperature limits are the same as those forthe ice machine. Limitations: l Must mee...
Page 4 - Diagrams CD300
Page 5 - Uncrating CD300; Return the unit to an upright position.; Leg Package Location
Uncrating CD300 Page 4 Remove the carton from the skid. Cut the plastic straps that secure the leg kit to the skid andremove the box. Use the dispenser carton as a cushion and lay the dispenser down on its back. Remove the boltsholding the skid to the machine, and separate the skid from the dispense...
Page 6 - Ice Machine Installation CD300; Adjustable Legs
Ice Machine Installation CD300 Page 5 All models: Place the dispenser in the location where it will be used. Level the top edge of thedispenser front to back and left to right with the adjustable legs. Place the ice machine on the dispenser and secure it to the dispenser with the hardware andstraps....
Page 7 - Utility Connections CD300; Drain Connections -Follow all applicable codes.
Utility Connections CD300 Page 6 Drain Connections -Follow all applicable codes. As ice melts in the dispenser, the water must be drained away. It is critical that a proper drain beconnected to the dispenser. Remember that this is a gravity drain system, the drain tubing mustslope down a minimum of ...
Page 8 - Initial Start Up and Use CD300; Final Check List; Record the ice machine model and serial number on the last page; How To Use – Push Button
Initial Start Up and Use CD300 Page 7 Final Check List 1. Is the ice machine properly installed?2. Is the dispenser level?3. Has the water supply been connected to the ice machine?4. Has the proper power been connected to the ice machine and dispenser? Note: When electrical power is supplied to the ...
Page 9 - Sanitation / Maintenance CD300; Schedule; remove the metal parts.
Sanitation / Maintenance CD300 Page 8 Schedule An ice system represents a sizable investment of time and money in any company’s business. Inorder to receive the best return on that investment, periodic maintenance is required. It is the userresponsibility to see that the machine is properly maintain...
Page 10 - Component Identification CD300; View when sink assembly is removed.
Component Identification CD300 Page 9 View when sink assembly is removed. Rotor as seen from the top. Inside view of ice chute. Rotor shaft.
Page 11 - Maintenance CD300
Maintenance CD300 Page 10 Regular inspection and maintenance will provide the best assurance of trouble free operation. Begin by removing the sink assembly. Check the action of the ice chute and return springs. Return Springs Check and Tighten Fasteners Clean out the lower drain pan. Pour hot water ...
Page 12 - Service Diagnosis CD300; Symptom
Service Diagnosis CD300 Page 11 Symptom Probable Cause Possible Correction Does not dispense. No power to dispenser. Check for power. Ice chute not all the way up. Push ice chute up. No ice in hopper. Check ice machine, it maybe off or the dispenser’sstorage capacity may havebeen exceeded. Dispenser...
Page 13 - Adjustments CD300
Adjustments CD300 Page 12 The gear motor cam must be properly adjusted to properly position the dispensing rotor. 1. Disconnect electrical power to the dispenser.2. Locate the sink key, unlock sink and remove it from the dispenser. 3. Observe the position of the rotor through the cube chute. The rot...
Page 14 - Removal and Replacement CD300; Rotor
Removal and Replacement CD300 Page 13 Rotor 1. Disconnect electrical power to the dispenser and ice machine. 2. At the back, remove two bolts securing the ice machine to the dispenser. If a bin thermostat is being used, pullthe thermostat capillary tube up and out of the hopper. 3. Push the ice mach...
Page 15 - Wiring Diagram CD300; Button Dispensing
Wiring Diagram CD300 Page 14 Button Dispensing Model CD300P
Page 16 - Schematic Diagram CD300
Schematic Diagram CD300 Page 15 Button Dispensing Model CD300P
Page 17 - Coin Mechanism
Page 19 - Key Card
Page 21 - Before Calling For Service CD300; ON; Record this information for future reference.; Dispenser
Before Calling For Service CD300 Page 20 Check these things. 1. Is the dispenser plugged in?2. Has the dispenser’s internal switch been switched to the ON position? 3. Is the ice machine plugged in?4. Has the ice machine’s internal switch been switched to the ON position? 5. Is there ice in the disp...