Page 2 - Safe Operation Practices for Ride-On Mowers; GENERAL OPERATION; SAFETY RULES; WARNING; The engine exhaust from this product con-
2 Safe Operation Practices for Ride-On Mowers I M P O R T A N T : T H I S C U T T I N G M A C H I N E I S C A P A B L E O F A M P U T A T I N G H A N D S A N D F E E T A N D T H R O W I N G O B J E C T S .F A I L U R E T O O B S E R V E T H E F O L L O W I N G S A F E T Y I N S T R U C T I O N S C O...
Page 3 - PRODUCT SPECIFICATIONS; CUSTOMER RESPONSIBILITIES
3 PRODUCT SPECIFICATIONS HORSEPOWER: 13.0 GASOLINE CAPACITY 2 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF/SG): SAE 30 (above 32°F)SAE 5W-30 (below 32°F) OIL CAPACITY: W/O FILTER: 3 PINTS SPARK PLUG: CHAMPION RJ19LM (GAP: .030") VALVE CLEARANCE: INTAKE: .005" - .007" EXHAUST: .009...
Page 4 - TABLE OF CONTENTS; INDEX
4 TABLE OF CONTENTS A Adjustments: Brake ............................................ 20Carburetor ................................... 23Mower Front-To-Back ......................... 19 Side-To-Side ........................... 19Throttle Control Cable .................. 22 Air Filter, Engine ..........
Page 5 - CONTENTS OF HARDWARE PACK; Parts packed separately in carton
5 CONTENTS OF HARDWARE PACK Parts packed separately in carton Parts Bag contents shown full size Parts bag contents not shown full size Slope Sheet (2) Hex Bolts 1/4-20 x 3/4 (2) Washers 9/32 x 5/8 x 16 Ga. (2) LockWashers 1/4 (2) Hex Nuts1/4-20 Seat Manual SteeringWheel Parts Bag (2) WeldNuts #10 (...
Page 6 - ASSEMBLY; TOOLS REQUIRED FOR ASSEMBLY; UNPACK CARTON; BEFORE ROLLING TRACTOR OFF SKID
ASSEMBLY 6 Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Usethe correct tools as necessary to insure proper ti...
Page 9 - CHECK TIRE PRESSURE; CHECKLIST; PLEASE REVIEW THE FOLLOWING CHECKLIST:
ASSEMBLY 9 TO CONVERT TO BAGGING ORDISCHARGING Simply remove mulcher plate and store in a safe place.Your mower is now ready for discharging or installation ofoptional grass catcher accessory. NOTE: It is not necessary to change blades. The mulcherblades are designed for discharging and bagging also...
Page 10 - OPERATION; KNOW YOUR TRACTOR; LIGHT SWITCH POSITION: Turns the headlights on.
OPERATION 10 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Savethis manual for future reference. FIG. 9 Our tractors conform to the ...
Page 11 - HOW TO USE YOUR TRACTOR; NOTE: Failure to move throttle control to slow (
OPERATION 11 HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE (See Fig. 10) Your tractor is equipped with an operator presence sensingswitch. When engine is running, any attempt by theoperator to leave the seat without first setting the parkingbrake will shut off the engine. • Depress clutch/brake pedal...
Page 12 - TO TRANSPORT; BEFORE STARTING THE ENGINE; ADD GASOLINE; TO OPERATE ON HILLS; and
OPERATION 12 TO OPERATE MOWER (See Fig. 11) Your tractor is equipped with an operator presence sensingswitch. Any attempt by the operator to leave the seat withthe engine running and the attachment clutch engaged willshut off the engine. • Select desired height of cut. • Start mower blades by engagi...
Page 13 - MOWING TIPS; MULCHING MOWING TIPS
OPERATION 13 TO START ENGINE (See Fig. 9) When starting engine for the first time or if engine has runout of fuel, it will take extra cranking time to move fuel fromthe tank to the engine. • Depress clutch/brake pedal and set parking brake. • Place gearshift lever in neutral (N) position. • Move att...
Page 14 - LUBRICATION CHART; GENERAL RECOMMENDATIONS; BEFORE EACH USE; MAINTENANCE SCHEDULE; SERVICE DATES
14 CUSTOMER RESPONSIBILITIES 2 LUBRICATION CHART 2 SPINDLE ZERK FRONT WHEELBEARING ZERK ATTACHMENTCLUTCHPIVOT(S) 1 SPINDLE ZERK FRONT WHEELBEARING ZERK 2 2 3 ENGINE GEARSHIFTPIVOTS 1 2 1 3 GENERAL RECOMMENDATIONS The warranty on this tractor does not cover items that havebeen subjected to operator a...
Page 15 - TRACTOR; BRAKE OPERATION; BATTERY
CUSTOMER RESPONSIBILITIES 15 TRACTOR Always observe safety rules when performing any mainte-nance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distanceat high speed in highest gear, then brake must be adjusted.(See “TO ADJUST BRAKE” in the Service and Adjust-ments section of ...
Page 16 - ENGINE; LUBRICATION; TRANSAXLE COOLING
CUSTOMER RESPONSIBILITIES 16 ENGINE LUBRICATION Only use high quality detergent oil rated with API serviceclassification SF or SG. Select the oil’s SAE viscosity gradeaccording to your expected operating temperature. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE SAE VISCOSITY GRADES -20° 0° 3...
Page 17 - MUFFLER; CLEANING
CUSTOMER RESPONSIBILITIES 17 MUFFLER Inspect and replace corroded muffler and spark arrester (ifequipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowingseason or after every 100 hours of operation, whicheveroccurs first. Spark plug typ...
Page 18 - SERVICE AND ADJUSTMENTS; Depress clutch/brake pedal fully and set parking brake.
SERVICE AND ADJUSTMENTS 18 CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:• Depress clutch/brake pedal fully and set parking brake. • Place gearshift lever in neutral (N) position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key “OFF” and remove key. • Make sure the bl...
Page 19 - TO LEVEL MOWER HOUSING
SERVICE AND ADJUSTMENTS 19 NUT "E" TRUNNION FRONT LINKS NUT "F" FIG. 24 TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground ordriveway. Make sure tires are properly inflated (See“PRODUCT SPECIFICATIONS” on page 3 of this manual).If tires are over or underi...
Page 21 - TO ADJUST STEERING WHEEL ALIGNMENT
21 SERVICE AND ADJUSTMENTS TRANSAXLE SHIFTER LINKAGE AND AD-JUSTMENT (See Figs. 28 and 29) The transaxle should be in neutral when the gear shift leveris in the neutral (N) (lock gate) position. The adjustment ispreset at the factory; however, if adjustment is needed,proceed as follows: • Make sure ...
Page 22 - TO REPLACE HEADLIGHT BULB
22 SERVICE AND ADJUSTMENTS CABLES NEGATIVE TERMINAL POSITIVE TERMINAL CHASSIS CHARGEDBATTERY POSITIVE TERMINAL NEGATIVE TERMINAL FIG. 31 TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of thegrill. • Replace bulb in holder and push bulb holder securelyback ...
Page 24 - STORAGE; FUEL SYSTEM; ENGINE OIL; OTHER
24 STORAGE Immediately prepare your tractor for storage at the end ofthe season or if the tractor will not be used for 30 days ormore. CAUTION: Never store the tractor withgasoline in the tank inside a buildingwhere fumes may reach an open flameor spark. Allow the engine to coolbefore storing in any...
Page 25 - TROUBLESHOOTING POINTS; PROBLEM
25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter. 5. Clean/r...
Page 27 - SCHEMATIC; WIRING INSULATED CLIPS; IGNITION SWITCH
27 TRACTOR - MODEL NO. LT130 (954830071A) SCHEMATIC BATTERY G B S M L IGNITION SWITCH NON-REMOVABLECONNECTIONS REMOVABLECONNECTIONS WIRING INSULATED CLIPS NOTE: IF WIRING INSULATEDCLIPS WERE REMOVED FORSERVICING OF UNIT, THEYSHOULD BE REPLACED TOPROPERLY SECURE YOUR WIRING BLACK RED RED BLACK RED WH...
Page 28 - REPAIR PARTS; ELECTRICAL
REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) ELECTRICAL 28 39 38 36 28 29 26 24 42 43 44 44 25 41 19 20 19 20 36 40 33 32 31 30 48 15 9 7 8 6 3 4 2 1 22 21 70 52 36 39 35 36
Page 29 - KEY
REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) ELECTRICAL 29 KEY PART NO. NO. DESCRIPTION 1 532144925 Battery 12 Volt 25 AMP 2 874760412 Bolt Hex Hd 1/4-20unc X 3/4 3 819091016 Washer 9/32 X 5/8 X 16 Ga. 4 810040400 Washer Lock Hvy Helical 1/4 6 873220400 Nut Fin Hex 1/4-20 Unc 7 532109238 Tube...
Page 30 - CHASSIS AND ENCLOSURES
30 REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) CHASSIS AND ENCLOSURES 3 2 3 38 39 35 26 35 26 33 10 34 3 1 8 68 14 14 9 48 4 11 17 29 129 134 28 14 4 14 13 49 49 57 52 51 50 58 37 20 37 23 24 26 25 26 25 3 31 24 30 3 6 51 57 53 52 53
Page 32 - DRIVE
REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) DRIVE 32 29 28 12 14 41 42 40 38 42 39 89 57 90 51 42 19 74 75 78 76 77 1 25 19 24 2 53 46 45 44 35 34 37 36 35 27 19 48 62 36 64 65 49 47 26 50 45 59 56 66 19 72 55 63 56 70 77 42 61 31 58 22 27 26 6 5 18 19 5 18 6 85 52 61 30 32 32 30 52 61 11 85...
Page 33 - DESCRIPTION
REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) DRIVE 33 KEY PARTNO. NO. DESCRIPTION KEY PARTNO. NO. DESCRIPTION 1 532142603 Transaxle 6sp Dana 4360-79 2 532146682 Spring Return Brake T/a Zinc 3 532123666 Pulley Transaxle 18"tires 4 812000028 Ring Retainer # 5100-62 5 874490544 Bolt Hex FLGH...
Page 34 - STEERING ASSEMBLY
34 REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) STEERING ASSEMBLY 5 9 5 7 7 9 4 3 32 43 6 43 8 18 19 22 21 20 8 27 62 23 11 12 24 29 25 5 8 10 12 11 11 15 8 6 9 46 46 8 6 9 2 47 14 13 47 16 16 38 40 39 1 41 17 42 37 36 50 44 51 54 57 37 50 55 26 30 28
Page 36 - SEAT ASSEMBLY
REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) SEAT ASSEMBLY 36 KEY PARTNO. NO. DESCRIPTION KEY PARTNO. NO. DESCRIPTION 1 532140838 Seat V250 2 532140551 Bracket Pivot Seat 8 720 3 874760616 Bolt Fin Hex 3/8-16unc X 1 4 819131610 Washer 13/32 X 1 X 10 Ga 5 532145006 Clip Push-In 6 873800600 Nut...
Page 37 - DECALS
REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) DECALS 37 9 3 4 8 KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 1 532059192 Cap Valve Tire 2 532065139 Stem Valve 3 532106222 Tire F Ts 15 X 6 0 - 6 Service 4 532059904 Tube Front (Service Item Only) 5 532138336 Rim Asm 6"front Silv...
Page 38 - OPTIONAL EQUIPMENT
REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) ENGINE 38 24 23 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 44 46 32 31 33 37 33 40 62 13 4 72 78 81 3 14 38 15 16 78 19 18 22 30
Page 40 - MOWER DECK
REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) MOWER DECK 40 15 14 12 13 11 10 9 8 16 68 36 37 30 31 32 33 35 49 50 51 54 52 53 34 55 56 40 17 1 46 44 21 22 24 25 26 27 2 28 29 23 21 21 21 18 18 20 19 4 3 5 6 2 21 58 48 59 84 83 36 37 40 85 43 72 41 74 75 76 77 79 40 80 73 78 45 71 45 81 82 67 ...
Page 42 - MOWER LIFT
42 REPAIR PARTS TRACTOR - MODEL NO. LT130 (954830071A) MOWER LIFT 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 8 10 12 11 31 32 31 32 19 19 13 13 13 13
Page 46 - SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION
46 15° MAX. SIGHT AND HOLD THIS LEVEL WITHSKY LINE OR TREE. CUT OUT ON DOTTED LINES THIS IS A 15° SLOPE SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL,NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION Operate your Tractor up and down the face of slopes (notgreater than 15°), never ac...
Page 47 - WARRANTY STATEMENT; 006-J PERIMETER WOODS DRIVE
Effective May 1, 1992 WARRANTY STATEMENT (2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna. (3) Alterations or modifications that affect the unit's performance, operation, safety, durability, change its intended u...
