Page 2 - KEY TO SYMBOLS; Key to symbols
2 – English KEY TO SYMBOLS Key to symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the mach...
Page 3 - CONTENTS; Contents
English – 3 CONTENTS Contents KEY TO SYMBOLS Key to symbols ............................................................. 2 CONTENTS Contents ...................................................................... 3 WHAT IS WHAT? What is what on the power cutter? ............................... 4 SAF...
Page 4 - What is what on the power cutter?
4 – English WHAT IS WHAT? What is what on the power cutter? 1 Diamond blade 2 Blade guard/spray guard 3 Hydraulic motor 4 Locking button for the drive wheel 5 Grease nipples 6 Control for the guide rollers 7 Front handle (adjustable) 8 Water adjustment control 9 Switch 10 Water connector 11 Coupling...
Page 5 - SAFETY INSTRUCTIONS; Personal protective equipment; Switch
English – 5 SAFETY INSTRUCTIONS Steps before using a new power cutter. • This machine is a hydraulically operated power cutter intended for free-hand cutting. The machine should be connected to a hydraulic unit with an oil flow of 35-42 litres/min and a maximum pressure of 150 bar. • Please read the...
Page 6 - Blade guard; s safety equipment; Checking the switch lock
6 – English SAFETY INSTRUCTIONS Switch lock and ON/OFF valve for the water The switch lock is designed to prevent accidental operation of the switch. The ON/OFF valve for the water supply is also controlled with the switch lock. When the switch lock (A) is pressed in this opens the water valve and r...
Page 7 - Checking the blade guard; General safety precautions; Transport and storage; General working instructions; Basic safety rules
English – 7 SAFETY INSTRUCTIONS Checking the blade guard Check that the guard is complete and without any cracks or deformations. General safety precautions • A power cutter is designed to cut hard materials, such as masonry. Observe the increased risk of kickback when cutting soft materials. See in...
Page 8 - Cutting; Cutting technique
8 – English SAFETY INSTRUCTIONS Cutting General • Start cutting with the machine running at maximum speed. • Always hold the machine in a firm grip with both hands. Hold it so that the thumbs and fingers grip round the handles. Cutting technique The technique described below is of a general characte...
Page 9 - How to avoid kickback
English – 9 SAFETY INSTRUCTIONS Large work Cuts exceeding 1 m - secure a batten along the line to be cut. The batten acts as a guide. Use this guide to make a marking cut along the entire length of the cut, 50-70 mm (2-3 inches) in depth. Remove the guides once the marking cut has been made. Small w...
Page 10 - Diamond blades
10 – English SAFETY INSTRUCTIONS • Be alert to movement of the work piece or anything else that can occur, which could cause the cut to close and pinch the blade. Pull in Pull in occurs when the disc’s lower section suddenly stops or when the cut closes. (To avoid, see the heading ”Basic rules” and ...
Page 11 - SETTINGS AND ADJUSTMENTS; Drive; Basic service; Fitting the blade
English – 11 SETTINGS AND ADJUSTMENTS Drive On account of the machine’s unique design the driving power is not transferred at the centre of the blade. The flanges on the two guide rollers run in the blade’s grooves. Springs on the guide rollers press out the rollers, which in turn press the V-shaped...
Page 13 - Hydraulic hoses; Water hose
English – 13 SETTINGS AND ADJUSTMENTS CAUTION! The machine should be upright. If the machine lies on its side the weight of the blade makes it difficult to make a correct adjustment. • Tighten the knobs fully and the machine is ready to use. Hydraulic hoses • Before connecting the hoses: Ensure that...
Page 14 - STARTING AND STOPPING; Starting and stopping; Starting; Stopping
14 – English STARTING AND STOPPING Starting and stopping Starting • Grip the front handle with the left hand. • Grip the rear handle with the right hand. When you grip the rear handle this releases the switch lock. Stopping The machine is stopped by releasing the switch. ! WARNING! Note the followin...
Page 15 - MAINTENANCE; Maintenance
English – 15 MAINTENANCE Maintenance Dismantling the complete guide roller • Remove the support roller cover. • Lift off the blade. • Unscrew the knob. First turn the knob a few turns until you feel a resistance. The guide roller then follows the knob out and stops when it feels a resistance. The gu...
Page 16 - Drive wheel
16 – English MAINTENANCE Drive wheel 1 Lock the axle using the locking button. See the instructions under the heading What is what?. 2 Loosen the centre screw and remove the washer. 3 You can now lift off the drive wheel. CAUTION! Replace the drive wheel when fitting a new blade. A worn drive wheel ...
Page 17 - Reconstructing the blade
English – 17 MAINTENANCE Reconstructing the blade Couplings 1 Water 2 Water filter 3 Return 4 Pressure IMPORTANT! If the coupling is dirty, the dirt can enter the oil and cause increased wear on the hydraulic motor, hydraulic pump, valves, etc. It can also prevent the coupling from sealing correctly...
Page 18 - Maintenance schedule
18 – English MAINTENANCE Maintenance schedule CAUTION! The chart is based on daily use of the equipment. Blades conforming to EN13236 Husqvarna K3600 MKII only conforms to 98/37/EC and EN13236 together with the blades listed below: Note: The blades are available in different hardnesses for different...
Page 19 - TROUBLE SHOOTING; Mechanics
English – 19 TROUBLE SHOOTING Mechanics Symptom Probable cause The blade does not rotate. Roller knobs not tightened fully. The blade not fitted on guide rollers correctly. Rollers tensioned too much. Possible faulty hose connection to the hydraulic system. Possible faulty hose connection to the dri...
Page 20 - TECHNICAL DATA; Extending the hydraulic hoses
20 – English TECHNICAL DATA *We recommend the use of environmentally approved hydraulic oil. **With high ambient temperatures use oil with a higher viscosity. Note 1: Noise emissions in the environment measured as sound power (L WA ) in conformity with EC directive 2000/14/EC. Note 2: Noise pressure...
Page 21 - EC-declaration of conformity
English – 21 TECHNICAL DATA EC-declaration of conformity Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter Husqvarna K 3600 dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by t...
Page 24 - Original instructions
´®z+UBT¶6A¨ 2010-01-13 ´®z+UBT¶6A¨ 1153345-26 Original instructions
