Husqvarna k2500 Manual — Free PDF Download

Page 2 - KEY; ey to symbols

2 – English KEY T O SYMBOLS K ey to symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the m...

Page 3 - CONTENTS; Contents

English – 3 CONTENTS Contents KEY TO SYMBOLS K ey to symbols ............................................................. 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHAT? What is what on the po wer cutter? ............................... 4 ...

Page 4 - WHA; What is what on the po

4 – English WHA T IS WHA T? What is what on the po wer cutter? 16 17 1 Cutting blade 2 Guard for the blade 3 Catch for the guard 4 Front handle 5 Water tap 6 Rating plate 7 Switch lock 8 Water connection with filter 9 Hydraulic hoses 10 Switch 11 Hydraulic motor 12 Flange washer 13 Belt guard 14 Bel...

Page 5 - SAFETY INSTR; Switc

English – 5 SAFETY INSTR UCTIONS Steps bef ore using a new power cutter. • This machine is a hydraulically operated power cutter intended for free-hand cutting. The machine should be connected to a hydraulic unit with an oil flow of 35-42 litres/min and a maximum pressure of 150 bar. • Please read t...

Page 7 - ransport and storage; General w; Basic saf

English – 7 SAFETY INSTR UCTIONS • Wear personal protective equipment. See instructions under the heading Personal protective equipment. • Never use a machine that has been modified in any way from its original specification. • Never use a machine that is faulty. Carry out the checks, maintenance an...

Page 8 - SAFETY INSTRUCTIONS; How to avoid kickback

8 – English SAFETY INSTRUCTIONS • Support the work piece in such a way that it is possible to predict what will happen, and so that the cut remains open while cutting. • Check that the blade is not in contact with anything when the machine is started • Always cut at maximum speed. • Start cutting sm...

Page 9 - Cutting blades; Abrasive discs

English – 9 SAFETY INSTRUCTIONS • Stand at a comfortable distance from the work piece. • Take care when inserting the blade in an existing cut. • Never cut above shoulder height. • Be alert to movement of the work piece or anything else that can occur, which could cause the cut to close and pinch th...

Page 10 - Diamond blades; Diamond blades for wet cutting

10 – English SAFETY INSTRUCTIONS Check that the blade is approved for the same or higher speed according to the aproval plate of the engine. Never use a cutting blade with a lower speed rating than that of the power cutter. Ensure the blade it not cracked or damaged in any other way. Test the abrasi...

Page 11 - ASSEMBLY; Assembly; Cutting arm; Guard for the blade

English – 11 ASSEMBLY Assembly Fitting the cutting blade Husqvarna’s blades are approved for hand-held power cutters. Blades are manufactured with three different diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1"). Bushings can be fitted on the machine axle to adj...

Page 12 - STARTING AND STOPPING; Starting and stopping; Starting; Stopping

12 – English STARTING AND STOPPING Starting and stopping Starting • Grip the front handle with the left hand. • Grip the rear handle with the right hand. When you grip the rear handle this releases the switch lock. Stopping The machine is stopped by releasing the switch. ! WARNING! Note the followin...

Page 13 - MAINTENANCE; Maintenance; Tensioning the drive belt; Replacing the drive belt; Water filter

English – 13 MAINTENANCE Maintenance Tensioning the drive belt The drive belt is fully enclosed and well protected from dust and dirt. When the drive belt is to be tensioned, release the nuts holding the cutting arm. Screw the adjuster screw so that the square headed nut comes opposite the marking o...

Page 14 - Daily maintenance

14 – English MAINTENANCE ´®z+R=@¶6r¨ ´®z+R=@¶6r¨ Daily maintenance Carry out the following checks daily before using the machine. 1 Check that nuts and screws are tight. 2 Check that the power source (the hydraulic unit) supplies the correct oil flow and oil pressure. 3 Check that the hydraulic hose...

Page 15 - TECHNICAL DATA; Technical data

English – 15 TECHNICAL DATA Technical data Note 1: Handle vibrations are measured according to ISO 8662-4 Cutting equipment EC-declaration of conformity (Applies to Europe only) Husqvarna Construction Products , SE-433 81 Partille, Sweden, tel: +46-31-949000, declares under sole responsibility that ...