Husqvarna 968999101 / W3212A - Manual

12 CUTTING HEIGHT ADJUSTMENT CHART AXLE POSITION NUMBER OF SPACERS BELOW CASTER ARM NUMBER OF 1/4" BLADE SPACERS UNDER CUTTER HOUSING CUTTING HEIGHT (IN INCHES) 1 1/21 3/4 22 1/42 1/21 3/4 22 1/42 1/22 3/42 1/22 3/4 33 1/43 1/2 33 1/43 1/23 3/4 43 1/43 1/23 3/4 44 1/43 1/23 3/4 44 1/44 1/23 3/4 ...

13 BRAKE / TRACTION ADJUSMENT 1. Disconnect the brake linkage from the brakeband arm. 2.With the mower in gear, place the drive leversin the drive position. Firmly pull back on thehandles until the tires slide to seat the drivebelts into the pulleys. 3. Measure the distance between the back drivelev...

15 Figure 6 AUXILARY BELT ADJUSTMENT ROD IDLER PIVOT POINT TURNBUCKLE ENGAGEMENT IDLER ASSEMBLY 1/4" BEFORE OPERATINGBe thoroughly familiar with all controls and howto use them before operating the mower. Knowbeforehand how to stop the engine, drivewheels, and mower blades in preparation forposs...

16 Adjustment Instructions for: MODELS / I.D. : 968999105 / WH3614A 968999111 / WH3615A 968999106 / WH4817A CUTTING HEIGHT 1. Before changing cutting heights make sure the blades are off, key switch is off, and removespark plug wire or wires.2. Cutting height ranges from 1 1/2” to 5” in 1/4” increme...

18 CUTTING HEIGHT ADJUSTMENT CHART Note: To quickly achieve small changes in cuttingheights, move the spacers from under the cutter housingto above the cutter pulley. (Each spacer moved will givean additional 1/4" of cutting height ). USE ONLY 4 BLADE SPACERS MAXIMUM AXLE POSITION NUMBER OF SPAC...

19 Figure 4 (Right side cut away view of console.) Figure 3 REVERSE SPRING DETENT ADJUSTMENT 1. To check if your reverse spring detent adjustment is set right. Make sure your ground speedlever is pulled back to the neutral position. Release the thumb latches (both sides) and pull up onthe control le...

20 Figure 5 AUXILARY BELT ADJUSTMENTROD IDLER PIVOT POINT TURNBUCKLE ENGAGEMENT IDLERASSEMBLY 1/4" BLADE DRIVE BELT ADJUSTMENT 1. Before performing adjustments on blade belt, turn the mower off and disconnect spark plug wireor wires.2. Remove front deck belt shield.3. Loosen nut on turnbuckle.4....

21 ENGINE BELT GUIDES 1. Before performing adjustments on belt guides, turn the mower off and disconnect spark plug wireor wires.2. Belt guides under the engine should be adjusted as shown in figure 6. Figure 6 PUMP BELT 1. Before performing adjustments on pump belt, turn the mower off and disconnec...

22 Models: 968999127 / WHF4215ETS968999129 / WHF4818ETS968999130 / WHF5218ETS ETS Hydro Intermediate Walk Behind

24 ADJUSTMENTS FRONT DECK BELT ROUTING: PUMP BELT 1. Before performing adjustments on pump belt, turn the mower off and disconnect spark plug wire orwires.2. Check tension on the belt. If it feels loose adjustment will need to be made.3. Loosen the nut on the bottom of the idler pulley.4. Slide the ...

25 Mid Mount Zero Turn Riders 42” & 48” 968999157 / ZTHKH4818A968999158 / ZTHKH4820A 968999167 / ZTHKW4218A968999168 / ZTHKW4818A968999169 / ZTHKW4821A MODEL / I.D. : Setup Instructions for: ADJUSTMENTS PARK BRAKE:1. Stop engine and remove key. While the park brake lever”A” is in the on position...

26 FIGURE 2 CUTTING HEIGHT:1. Stop the mower and disengage the blades.2. Raise the deck height lever to the transport position.3. Remove the height adjustment pin and place it in the desired cutting height hole. Move deckheight lever down onto the pin and mow. NOTE: anti-scalp rollers must be in the...

31 Adjustments Cutting HeightStop the mower and disengage the blades. Raise the deck height lever to the transportposition. Remove the height adjustment pin andplace it in the desired cutting height hole.Lower the lift lever down onto pin. NOTE:Anti-scalp rollers must be in the properposition for ma...