Page 2 - Intended use
Contents Introduction..................................................................... 2Safety..............................................................................4Assembly........................................................................ 9Operation...................................
Page 3 - Symbols on the product
17. Muffler18. Chain brake and front handguard19. Front handle20. Switch for heated handles (560XPG Mark II, 562XPG Mark II) 21. Right handguard22. Clutch cover23. Clutch/clutch drum24. Oil pump adjustment screw25. Chain tensioning screw26. Chain catcher27. Spiked bumper28. Saw chain29. Guide bar30....
Page 4 - Euro V Emissions; Safety; Safety definitions
yyyywwxxxx The rating plate or the laser print shows serial number. yyyy is the pro- duction year and ww is the production week. Note: Other symbols/decals on the product refer to certification requirements for some markets. Euro V Emissions WARNING: Tampering with the engine voids the EU type-appro...
Page 9 - Assembly; Introduction
• Only use approved guide bar/saw chain combinations and filing equipment. Refer to Accessories on page 35 for instructions. • Use protective gloves when you use or do maintenance on the saw chain. A saw chain that does not move can also cause injuries. • Keep the cutting teeth correctly sharpened. ...
Page 10 - To assemble a spiked bumper; Operation; Premixed fuel
6. Align the hole in the guide bar with the chain adjuster pin and install the clutch cover. 7. Tighten the bar nuts finger tight.8. Tighten the saw chain. Refer to To adjust the tension of the saw chain on page 28 for instructions. 9. Tighten the bar nuts. Note: Some models have only one bar nut. T...
Page 12 - To fill the chain oil tank; Kickback information; Common questions about kickback
WARNING: The saw chain can break if the lubrication of the cutting equipment is not sufficient. Risk of serious injury or death to the operator. WARNING: This product has a function that lets the fuel run out before the chain oil. Use the correct chain oil for this function to operate correctly. Spe...
Page 13 - To start the product; To prepare to start the product
• Will the chain brake always protect me from injury during a kickback?No. The chain brake must operate correctly to give protection. The chain brake must also be engaged during a kickback to stop the saw chain. If you are near the guide bar, it is possible that the chain brake does not have time to...
Page 14 - To use the spiked bumper
To stop the product 1. Push the start/stop switch down to stop the engine. Pull stroke and push stroke You can cut through wood with the product in 2 different positions.• To cut on the pull stroke is when you cut with the bottom of the guide bar. The saw chain pulls through the tree when you cut. I...
Page 16 - To use the tree felling technique
1 2 3 1. Remove the limbs on the right side of the trunk. a) Keep the guide bar on the right side of the trunk and keep the body of the product against the trunk. b) Select the applicable cutting technique for the tension in the branch. WARNING: If you are not sure about how to cut the branch, speak...
Page 18 - To fell a tree
1 2 2 1 3 To fell a tree Husqvarna recommends you to make the directional cuts and then use the safe corner method when you fell a tree. The safe corner method helps you to make a correct felling hinge and control the felling direction. WARNING: Do not fell trees with a diameter that is more than tw...
Page 19 - To free a trapped tree
1. If the usable cutting length is longer than the tree diameter, do these steps (a-d).a) Make a bore cut straight into the trunk to complete the felling hinge width. b) Cut on the pull stroke until ⅓ of the trunk is left.c) Pull the guide bar 5-10 cm/2-4 in rearward.d) Cut through the remaining of ...
Page 20 - To cut trees and branches that are in tension; To use the product in cold weather
To cut trees and branches that are in tension 1. Figure out which side of the tree or branch that is in tension. 2. Figure out where the point of maximum tension is. 3. Examine which is the safest procedure to release the tension. Note: In some situations the only safe procedure is to use a winch an...
Page 21 - Electrical carburetor heating (560 XPG Mark; Maintenance
Heated handles (560 XPG Mark II, 562 XPG Mark II) The product has heated front and rear handles. The electrical heating coils are powered by a generator.Push the switch in the direction of the arrow to engage the function. Push the switch in the opposite direction to disengage the function. Electric...
Page 22 - To do a check of the brake band
Daily maintenance Weekly maintenance Monthly maintenance Do a check of the saw chain. Refer to To examine the cutting equipment on page 30. Clean between the cylinder fins. Empty the oil tank. Sharpen the saw chain and do a check of its tension. Refer to To sharpen the saw chain on page 26. Do a che...
Page 24 - To do a check of the muffler
To do a check of the vibration damping system 1. Make sure that there are no cracks or deformation on the vibration damping units. 2. Make sure that the vibration damping units are correctly attached to the engine unit and handle unit. Refer to Product overview on page 2 for information about where ...
Page 26 - Information about the guide bar and saw chain
3. Tighten the screws that hold the starter. To clean the air filter Clean the air filter regularly from dirt and dust. This prevents carburetor malfunctions, starting problems, loss of engine power, wear to engine parts and more fuel consumption than usual.1. Remove the cylinder cover and the air f...
Page 28 - To adjust the tension of the saw chain
file gauge. This will help you to keep maximum cutting performance and the kickback risk at a minimum. WARNING: The force of the kickback increases a lot if you do not follow the sharpening instructions. Note: Refer to for information about sharpening of the saw chain. To sharpen the cutters 1. Use ...
Page 31 - Recommended settings for the oil pump; Air cleaning system
7. Turn the guide bar daily to extend its life cycle. To do maintenance on the fuel tank and the chain oil tank • Drain and clean the fuel tank and the chain oil tank regularly. • Replace the fuel filter yearly or more frequently if necessary. CAUTION: Contamination in the tanks causes malfunction. ...
Page 32 - Troubleshooting; The engine does not start
Troubleshooting The engine does not start Product part to examine Possible cause Action Starter pawls The starter pawls are blocked. Adjust or replace the starter pawls. Clean around the pawls. Speak to an approved service work- shop. Fuel tank Incorrect fuel type. Drain the fuel tank and fill with ...
Page 33 - Transportation and storage; Technical data
Transportation and storage Transportation and storage • For storage and transportation of the product and fuel, make sure that there are no leaks or fumes. Sparks or open flames, for example from electrical devices or boilers, can start a fire. • Always use approved containers for storage and transp...
Page 35 - Accessories; Recommended cutting equipment
Accessories Recommended cutting equipment Chainsaw models Husqvarna 560XP Mark II, 560XPG Mark II, 562XP Mark II, 562XPG Mark II have been evaluated for safety according to EN ISO 11681-1:2011 (Machinery for forestry - Portable chainsaw safety requirements and testing) and fulfill the safety require...
Page 36 - Filing equipment and filing angles
Approved cutting equipment for Husqvarna 560XP Mark II, Husqvarna 560XPG Mark II: Guide bar Saw chain Length, in/cm Pitch, in Gauge, in/mm Max. nose ra- dius Type Length, drive links (no.) Low kickback 13/33 0.325 0.058/1.5 11T Husqvarna C35 56 No 15/38 64 16/40 11T or 12T or 34 mm 66 18/45 72 20/50...
Page 38 - Declaration of Conformity; EC Declaration of conformity
Declaration of Conformity EC Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Chainsaws for forest service Brand Husqvarna Type / Model 560XP Mark II, 560XPG Mark II, 562XP Mark II, 562XPG Ma...
Page 39 - Declaration of conformity
Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Chainsaws for forest service Brand Husqvarna Type / Model 560XP Mark II, 560XPG Mark II, 562XP Mark II, 562XPG Mark II Identification Serial n...
