Page 2 - Product description
Contents Introduction..................................................................... 2Safety..............................................................................4Assembly...................................................................... 11Operation....................................
Page 3 - Symbols on the product
9. Power trigger10. Rear handle11. Front handle12. Flexible cord13. Battery charger (Accessory)14. Power indicator15. Battery release buttons16. Battery (Accessory)17. Warning indicator18. Battery indicator button19. Battery status20. Start and stop button21. SavE button22. Harness23. 4 mm hex key24...
Page 4 - Product damage; Safety; Safety definitions
This product is not electrically insulated. If the product touches or comes close to high-volt- age power lines it could lead to death or serious injury. Electricity can jump from one point to another by arcing. The higher the voltage, the greater the distance electricity can jump. Electricity can a...
Page 8 - Personal protective equipment
your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability. • Avoid all usage which you consider to be beyond your capability. • Never use the product if you are fatigued, while under the influence of alcohol or drugs, medication or anything that could affe...
Page 9 - Safety devices on the product
• Use a visor for face protection. A visor is not enough for protection of the eyes. + • Use gloves when necessary, for example when you attach, examine or clean the cutting equipment. • Use sturdy non-slip boots or shoes.• Use clothing made of a strong fabric. Always use heavy, long pants and long ...
Page 10 - Battery safety
3. Make sure that the power trigger and the power trigger lockout moves freely and that the return springs operate properly. 4. Start the product, refer to To start the product on page 14. 5. Push the power trigger fully to apply full speed.6. Release the power trigger and make sure that the cutting...
Page 11 - Battery charger safety; Safety instructions for maintenance; Assembly; Introduction
• Do not try to disassemble or break the battery.• Do not let battery acid touch your skin. Battery acid causes injuries to the skin, corrosion and burns. If you get battery acid in your eyes, do not rub but flush with water for minimum 15 minutes. If battery acid has touched your skin, you must cle...
Page 13 - Operation
3. Adjust the length of the harness until the harness support hook is in level with your hip. To connect the battery charger 1. Connect the battery charger to the voltage and frequency that is specified on the rating plate. 2. Put the plug in a grounded socket outlet. The LED on the battery charger ...
Page 15 - To use the product
3. Push the release buttons on the battery and pull the battery out. To use the product WARNING: Do not stay directly below a branch that is being cut. This can result in death or injury. • Be careful when you operate near overhead power lines. Falling branches can result in short-circuiting. • If p...
Page 16 - Maintenance
Maintenance Introduction WARNING: Read and understand the safety chapter before you do maintenance work on the product. WARNING: Remove the battery before you do maintenance on the product. Maintenance schedule WARNING: Remove the battery before you do maintenance. The following is a list of the mai...
Page 17 - To check the saw chain
Maintenance Daily Weekly Monthly Do a check of the connections between the battery and the product. Do a check of the connection between the battery and the bat- tery charger. X Make sure that the saw head is not dam- aged. Replace the saw head if it is damaged. An approved Husqvarna dealer must do ...
Page 18 - To sharpen the saw chain; Information about the guide bar and saw chain
4. Examine the groove in the guide bar for wear. Replace the guide bar if it is necessary. 5. Examine if the guide bar tip is rough or very worn. 6. Make sure that the bar tip sprocket turns freely and that the lubricating hole in the bar tip sprocket is not blocked. Clean and lubricate if it is nec...
Page 21 - To lubricate cutting equipment
3. Lift the front of the guide bar and turn the chain tensioning screw. Use a wrench. 4. Tighten the saw chain until it is tight against the guide bar but still can move easily. 5. Tighten the bar nuts using the wrench and lift the front of the guide bar at the same time. 6. Make sure you can pull t...
Page 22 - Troubleshooting; Keypad
3. Check that the bar tip sprocket turns freely. If the chain lubrication system is still not working after carrying out the above checks you should contact your service workshop. To replace the chain drive sprocket 1. Remove the bar nut (A) that holds the clutch cover.2. Remove the clutch cover (B)...
Page 23 - Transportation, storage and disposal
Problem Possible faults Possible solution The product does not start. Dirt in the battery connectors. Clean the battery connectors with com- pressed air or a soft brush. Red error LED comes on. It is necessary to do servicing on the product. Speak to your servicing dealer. Battery LED display Possib...
Page 24 - Technical data
• Charge the battery 30% to 50% before you put it in storage for long periods. • Put the battery charger in storage in a space that is closed and dry. • Keep the battery away from the battery charger during storage. Do not let children and other not approved persons to touch the equipment. Keep the ...
Page 25 - Accessories; Approved batteries for the product
530iP4 530iPT5 Short shaft front/rear handle - 1.4/1.2 Accessories Approved batteries for the product Battery BLi200 40-B220X Type Lithium-ion Lithium-ion Battery capacity, Ah 5.2 6.0 Nominal voltage, V 36 36 Weight, kg 1.3 1.4 Approved battery chargers for the product Battery charger QC330 QC500 Ma...
Page 27 - Declaration of Conformity; EU Declaration of Conformity
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Pole Hedge Trimmer Brand Husqvarna Type / Model 530iP4, 530iPT5 Identification Serial numbers da...
Page 28 - Declaration of conformity
Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Pole Pruner Brand Husqvarna Type / Model 530iP4, 530iPT5 Identification Serial numbers dating from 2022 and onwards complies ...
