Page 2 - Product description
Contents Introduction..................................................................... 2Safety..............................................................................4Assembly........................................................................ 9Operation...................................
Page 3 - Symbols on the product
3. Bevel gear4. Cutting attachment guard5. Shaft6. Handlebar7. Throttle control8. Stop switch9. Throttle lockout10. Suspension ring11. Cylinder cover12. Starter rope handle13. Fuel tank14. Choke control15. Air purge bulb16. Air filter cover17. Handle adjustment18. Locknut19. Support flange20. Suppor...
Page 4 - Euro V Emissions; Safety; Safety definitions
yyyywwxxxx The rating plate shows the serial number. yyyy is the production year and ww is the production week. Note: Other symbols/decals on the product refer to certification requirements for other commercial areas. Euro V Emissions WARNING: Tampering with the engine voids the EU type-approval of ...
Page 5 - Personal protective equipment
• Refer to national or local laws. They can prevent or decrease the operation of the product in some conditions. • Do not use the product if you are fatigued or influenced by alcohol, drugs or medicine. They can have effects on your vision, alertness, coordination or judgment. Safety instructions fo...
Page 6 - Protective devices on the product
• If it is necessary, use approved protective gloves.• Use a helmet if it is possible that objects fall on your head. • Always use approved ear protection while you operate the product. Noise for a long period can cause noise-induced hearing loss. • Make sure that you have a first aid kit near. Prot...
Page 8 - Cutting equipment
Cutting equipment Choose and maintain the cutting equipment to:• Obtain maximum cutting performance.• Increase life span of the cutting equipment.• Follow the checking, maintenance and service instructions for the muffler. • Always use the recommended guard for the cutting equipment. See Technical d...
Page 9 - Fuel Safety; Safety instructions for maintenance; Assembly; Introduction
• Grass blades and grass cutters are used to cut rough grass. • A grass blade can cause injury while it continues to spin after the engine is stopped or the throttle trigger is released. Make sure that the grass blade has completely stopped rotating before any maintenance. • Stop the engine before y...
Page 10 - To attach a blade guard, grass blade and
To assemble the handlebar 1. Loosen the 2 screws on the handlebar bracket. 2. Put the handlebar bracket into position on the shaft. Tighten the 2 screws on the handlebar bracket. 3. Attach the brackets together with the handlebar on the handlebar bracket. 4. Tighten the handle adjustment knob slight...
Page 11 - To adjust the harness
Note: Use the recommended blade guard. Refer to Accessories on page 24. 1. Install the blade guard to the shaft. Attach the blade guard with the bolt (L). G E F D B C A A L 2. Attach the drive disc (B) to the output shaft.3. Turn the output shaft until 1 of the holes in the drive disc aligns with th...
Page 12 - Operation; Premixed fuel
6. Let the cutting attachment lightly touch the ground. Adjust the harness clamp to balance the product correctly. Note: If you use a grass blade, it must balance approximately 10 cm /4 in above the ground. Operation WARNING: Read and understand the safety chapter before you operate the product. Int...
Page 13 - To start and stop; Before you operate the product
To fill the fuel tank WARNING: Obey the procedure that follows for your safety. 1. Stop the engine and let the engine become cool.2. Clean the area around the fuel tank cap. 3. Shake the container and make sure that the fuel is fully mixed. 4. Remove the fuel tank cap slowly to release the pressure....
Page 16 - To stop the engine; To operate the grass trimmer; General work instructions
7. Reset the choke when the engine starts or after you pull the starter rope 5 times. 8. If it is necessary, pull the starter rope again and again until the engine starts. 9. Let the engine run for 10 seconds.10. Operate the throttle gradually.11. Make sure the engine runs smoothly. Note: If the eng...
Page 18 - To sweep the grass; Maintenance
4. Use full throttle when you move the product from side to side to cut grass. To sweep the grass The airflow from the rotating trimmer line can be used to remove cut grass from an area. 1. Hold the trimmer head and its trimmer line parallel to the ground and above the ground. 2. Apply full throttle...
Page 21 - Troubleshooting
To clean the air filter CAUTION: An air filter that is damaged, very dirty, or soaked with fuel must always be replaced. Clean the air filter from dirt and dust regularly. This prevents carburetor malfunctions, starting problems, loss of engine power, wear to engine parts and more fuel consumption t...
Page 22 - Transportation and storage
Starting failure Check Possible cause Solution Starter pawls Binding pawls Adjust or replace the pawls. Clean around the pawls. Speak to an approved servicing dealer. Fuel tank Incorrect fuel type. Drain it and use correct fuel. Carburetor Adjustment of the idle speed. Adjust the idle speed with the...
Page 23 - Technical data
Technical data Technical data 525RX Mark II 525RXT Mark II Engine Cylinder displacement, cm 3 25.4 25.4 Idle speed, rpm 3000 3000 Speed of output shaft, rpm 6500/7500 6500/7500 Catalytic converter muffler Yes Yes Maximum engine power acc. to ISO 8893, kW/hp @ rpm 1.0/1.34 @ 8500 1.0/1.34 @ 8500 Igni...
Page 24 - Accessories
Accessories Accessories Approved accessories Accessory type Cutting attachment guard, art. no. Grass blade/grass cutter Grass 255-4 1" (Ø 255 4 teeth) 588 11 79-01 Grass blade 255-3 (Ø 255 3 teeth) 588 11 79-01 Plastic blades Tricut Ø 300 mm (Separate blades have part number 531 07 77-15) 588 11...
Page 25 - Declaration of Conformity; EU Declaration of Conformity
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Brush cutters Brand Husqvarna Type / Model 525RX Mark II, 525RXT Mark II Identification Serial numbers dating fro...
Page 26 - UK Declaration of Conformity
UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Brush cutters Brand Husqvarna Type / Model 525RX Mark II, 525RXT Mark II Identification Serial numbers dating from 2023 and onwards complie...
