Hunter 51015 - Manual

1.888.830.1326 www.HunterFan.com Ceiling Bracket Installation OFF Make sure all four (4) bumpers are still attached. For angled ceilings, point opening toward peak. Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the c...

www.HunterFan.com 1.888.830.1326 Ceiling Bracket Installation (continued) Preparation 1.888.830.1326 www.HunterFan.com DISCA RD KEEP! Remove the shipping blocks from the motor. Save the five screws. They will be needed for blade iron installation. Time Saver Tip: Get a helper to insert grommets, fou...

1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a d...

KEEP! 8” 3/8” CU T & ST R IP (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downrod. Downrod (continued) 8” 3/8” Tig...

1.888.830.1326 9 M0001-01 • 08/03/12 • © Hunter Fan Company www.HunterFan.com Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan.

www.HunterFan.com 1.888.830.1326 Wiring FR O M F A N F RO M C E I LING B RA CK E T F R O M FA N Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. (G rounding) G reen...

www.HunterFan.com 1.888.830.1326 11 M0001-01 • 08/03/12 • © Hunter Fan Company Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Screw Holes Insert the two canopy screws found...

www.HunterFan.com 1.888.830.1326 Blades Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. 12 Insert grommets found in the hardware bag into the...

www.HunterFan.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the bag. Align the notches in the sides of the lower switch housing with the screws on...

www.HunterFan.com 1.888.830.1326 Light Kit (continued) CONGRATULATIONS! YOU’RE DONE! Install the bulbs into the sockets. When necessary, replace with bulbs of same wattage. Note: Glass shade style and number of lights may vary. See next page for fan operation instructions. Connect a pull chain penda...

www.HunterFan.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter Fan Company 16 Maintenance & Cleaning The fan pull chain controls the speed: high, medium, low, and off. The light pull chain controls the light fixture: on and off. To switch the direction of air flow, move the reverse switch to th...

www.HunterFan.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter Fan Company 17 Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Turn the power off, suppor t the fan carefully, and check that the hanger ball is properly seated. • Use the provi...