Hunter 24750 - Manual

© 2006 Hunter Fan Company

Fan High = 3
Fan Medium = 2
Fan Low = 1
Fan OFF = 0

Fan Operation

• ON, OFF, and Speed Setting: To turn the ceiling fan

on, press either “1”, “2”, or “3” on the remote control. To

change the speed of the ceiling fan, press “1” for slow,

“2” for medium, and “3” for fast. To turn the ceiling fan

off, press “0”.

To reverse the fan direction, turn the fan off and wait for

the blades to stop moving. Switch the reversing switch

on the fan to the opposite direction. Restart fan.

Light Operation

• ON and OFF: Press and quickly release the light button on the hand-held remote to turn the light

OFF and ON. See Figure 5 for remote button locations.

Dimmer

Press and hold the light button for more than one second to dim or brighten the light. If brightness is

initially at 100%, then the brightness will decrease as long as the light button is pressed. When the

minimum brightness of 25% is reached, the setting will pause and then begin to increase as long as

the light button is pressed.

43520-01 16/10/06

Remote Ceiling Fan & Light Control

Model: 24750
Transmitter Part Number: 87495-01
Transmitter Battery: 12V, Type A23, MN-21 or equivalent
Receiver Part Number: 87262-01
Ratings: 240 VAC, 50Hz, 1.0 Amp Fan
Receiver Weight: 160g
Max 300 Watts Incandescent or Halogen Light

Read and Save these Instructions

WARNING! Risk of Electrical Shock

• To avoid possible electrical shock, before wiring fan, disconnect power by turning off the power

mains both to the outlet box and to its associated wall switch location.

Compliance

• This equipment has been tested and complies with: EN 300220:2002 and EN 55022:1998 Class

B.

• All wiring must be in accordance with national and local electrical codes. If you are unfamiliar

with wiring, you should use a qualified serviceman.

• To avoid overheating and possible damage to other equipment, do not install to control

a receptacle, fluorescent light fixture, motor-operated appliance, or transformer-supplied

appliance.

• In Australia, national laws require a quailfied electrician to install this accessory into a ceiling

fan.

• Use only to control one paddle-blade ceiling fan and incandescent or halogen light fixture.

NOTE:

Any changes or modifications to the transmitter or receiver not expressly approved by Hunter

Fan Company may void one’s authority to operate this remote control.

For use only with electrically reversible ceiling fans rated at 1.0 A or less, and fan incandescent light

kits rated at 300 W or less.

If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

• Consult the dealer or an experienced radio/TV technician for help.

Installing the Receiver

Disconnect the power mains to the ceiling fan and light kit at the main electric panel. Remove fuse or

move circuit breaker to the OFF position. Turn off wall switch.

IMPORTANT!

Before installing this control, change the factory default DIP switch settings to your own

unique code. The DIP switches are under the battery compartment on the remote and are on the flat

side of the receiver. Refer to Figure 1. Remove the battery from the remote and turn off power to the

fan when making any DIP switch setting changes.

Figure 1 - Setting DIP Switches

Be sure the DIP switch settings of the transmitter and receiver match, or the ceiling fan will not function.

Make sure the DIP switch combination of your ceiling fan transmitter and receiver is different from the

DIP switch combinations of any other receivers and transmitters in your home (garage door openers,

other ceiling fans, entertainment equipment, etc.).

Install one type A23, MN-21 or equivalent, 12 volt alkaline battery inside the hand-held transmitter

after

setting the DIP switch settings on the remote to match the ON / OFF DIP switch settings on the

receiver. Refer to Figure 1.

Install the ceiling fan according to its instructions, up to the point of making the electrical connections.

Connecting Fan to Electrical Source

Use Figures 2 and 3, for reference in making the following electrical connections.

Connect the supply mains to the terminal block mounted on the hanger bracket.

Connect the safety earth (green/yellow) wire to the terminal marked

.

Connect the blue neutral wire to the terminal marked “N.”

Connect the brown line wire to the terminal marked “L.”

Note:

An additional “L” terminal is provided for separate control of the light fixture. This terminal is not

required for controlling the light fixture with the remote control.

Feed the electrical connector from the fan through the hole in the hanger bracket so it is on the outside

of the hanger bracket.

The remote receiver is connected between the electrical connector coming from the fan and the electrical

connector coming from the hanger bracket terminal block. See Figure 2.

Slide the remote receiver through the two rectangular openings in the hanger bracket and center it in

the hanger bracket, as shown in Figure 4.

The male connector on the remote receiver attaches to the female connector on the fan. The female

connector on the remote receiver attaches to the male connector on the hanger bracket. They are

keyed so they will only connect one way. See Figure 2.

Do not force the connectors. To aid in proper connection, align the color code stickers on each connector

so they are in line with each other then press them together until they lock.

CAuTIoN:

Be sure no bare wire or wire strands are visible after making connections.

Make sure none of the wires are caught in any of the hanging assembly components. The white

antenna wire should be extended to its full length and positioned between the hanger bracket

and the canopy parts upon final assembly.

Once the receiver is installed, continue with the appropriate instructions from the fan installation manual

to finish installing the fan.

Testing the Control

Warning!

-

Do not use the light fixture pull chain to operate the light while power is

applied to the receiver as damage could occur to the receiver. It is recommended to shorten the

pull chain(s) to prevent accidental use.

• Do not use the fan pull chain switch to operate the fan speeds while power is applied to the

receiver as damage could occur to the receiver.

When the installation is complete and while there is no power (your wall switch is in the OFF position)

to the receiver, pull the light kit’s pull chain once and pull the fan speed pull chain once.

Turn on the wall switch. The light kit should turn ON. If the light remains OFF, turn off the power at the

wall switch. Pull the light kit’s pull chain to turn the light ON.

Turn the wall switch back ON.

Press “3” on the remote control (refer to Figure 5). The fan should start and reach it’s maximum speed.

If the fan does not start or is turning too slow, turn off the power at the wall switch. Pull the fan’s pull

chain to change speed. Reapply power and try HIGH.

Hunter Fan Company

2500 Frisco Avenue

Memphis TN 38114 USA

Hunter Fan

Company

Figure 3 - Terminal Block Connections

Possible Causes

Main Power not restored.

Fan pull chain not set to HIGH.

Light pull chain not set to ON.

Receiver wiring incorrect.

Tr a n s m i t t e r a n d r e c e i v e r D I P

switches do not match.

Battery too weak.

S i g n a l b l o c k e d f r o m r e a c h i n g

receiver

Solution

2. Operates only at

close range.

Symptom

3. Inconsistent operation.

Replace fuse. Turn ON supply mains.

Turn ON wall switch.

Turn OFF power at wall switch or

main supply mains. Set fan to HIGH

speed.

Set light kit to ON.

Verify wiring connections.

Set transmitter and receiver to same

DIP switch setting.

Replace with new, alkaline battery.

Extend antenna into wire into ceiling

box, or move it for better reception.

1. No functions operate.

Battery too weak.

S i g n a l p a r t i a l l y b l o c k e d f r o m

reaching receiver.

RF interference.

Continuing RF interference.

Replace with new, alkaline battery.

Extend antenna into ceiling box, or

move it for better reception.

Turn OFF wall switch for 5 seconds,

then turn back ON.

Change dip switch settings to a

different code in both Transmitter

and Receiver.

Troubleshooting

Figure 2 - Wiring Diagram

Remote

Receiver

Hanger

Bracket

Figure 4 - Remote Receiver in Hanger Bracket

ON DIP

1

2

3

4

ON DIP

1 2 3 4

Receiver Back

Transmitter Back

Dip Switch

Dip Switch

Operation

Turn ON the wall switch, the light will turn ON at maximum brightness and the fan will be off.

Figure 5