Page 2 - Contents
Safety Copyright & Glossary Reference STB Connections Remote Control Unit Function Guide Main Menu Guide Motorised System Troubleshooting Guide Menu Map Specification GB2 GB3 GB4 ~ GB5 GB6 ~ GB11 GB12 ~ GB13 GB14 ~ GB18 GB19 ~ GB47 GB48 ~ GB52 GB53 GB54 ~ GB55 GB56 ~ GB57 GB1 Contents
Page 3 - Safety
Safety GB2 This STB has been manufactured to satisfy international safety standards.Please read the following safety precautions carefully. MAINS SUPPLY : 90 - 250 V AC 50/60 Hz OVERLOADING : Do not overload a wall outlet, extension cord or adapter as this may result in fire or electric shock. LIQUI...
Page 4 - is a trademark of France Telecom.; Copyright
Copyright & Glossary • VIACCESS TM is a trademark of France Telecom. • CryptoWorks(TM) is a trademark of Philips Electronics N.V.• Irdeto is a trademark of Mindport BV.• Nagravision is a registered trademark of Kudelski S.A.• Conax is a trademark of Telenor Conax AS. • HUMAX cannot be held respo...
Page 5 - References; other end to the LNB IN socket on the STB.; Connecting a Satellite antenna
References All our receivers are designed to be DiSEqC 1.0 compatible. This allows multiple antennaeto be connected to the STB simultaneously.If you have two or more fixed antennae or LNBs, you can use a DiSEqC 1.0 switch. 1. Connect the coaxial cable from the first LNB to the LNB 1 or LNB A DiSEqC ...
Page 6 - decide when and where to release via the satellite system).; Software Upgradeing
The HUMAX digital set-top box is a highly sophisticated product-incorporating one of the best software applications. Whenever a problem is found with this software or extra functions or enhanced applications are added, the software in the equipment must be upgraded. In order to maintain correct prod...
Page 7 - STB Connections; Front Panel
Page 8 - SLOT
(STANDBY) Press to switch between Operation and Standby modes. TV/RADIO Press to switch between TV and Radio modes. P- Use to change services down. P+ Use to change services up. V - (Model IR-ACE M only) Use to volume down. V+ (Model IR-ACE M only) Use to volume up. STANDBY LED (RED) Indicates that ...
Page 9 - Rear Panel
Page 11 - otherend to a RCA/Cinch socket on your TV.; TV with Terrestrial antenna
STB Connections 1. Connect one end of RCA/Cinch cable to the RCA/Cinch socket on the STB and the otherend to a RCA/Cinch socket on your TV. If your TV doesn’t have a RCA/Cinch socket, connect one end of RF cable to the RF OUT on STB and the other end to a RF input socket on your TV. 2. Connect the c...
Page 13 - Remote Control Unit; GREEN
Remote Control Unit TV/RADIO STANDBY GUIDE YELLOW BLUE EXIT CURSOR V-/V+ RCL (RECALL) HELP OPT+ (OPTION) MUTE SOURCE NUMERIC BUTTONS FAV (FAVOURITE) GREEN RED OK P-/P+ MENU i (INFORMATION) FREEZE GREEN RED YELLOW BLUE GREEN RED YELLOW BLUE GB12
Page 15 - Function Guide; • Current Time, Dolby Digital Symbol if there is an available Dolby; Service Part
Function Guide The detailed information on a service and its event is automaticallydisplayed at the bottom of the screen (I-Plate) whenever a servicechanges. To obtain this information when watching a service, pressthei ( ) button. If you press the i ( ) button again while the I-Plate is displayed, ...
Page 16 - Changing Services
If you press the HELP ( ) button while the I-Plate is displayed,the detailed description of the event will be displayed on the helpwindow instead of help messages. If there is no available data forthe detailed description on the air, the help message is displayed onthe help window instead. There are...
Page 17 - NOTE: The Dolby decoder with optical port shall be connected; Soundtrack
To change the audio language in the current service, proceed as follows: 1. Press the OPT+ ( ) button and select the Soundtrack item.2. Press the button to activate the list of supported audio languages. 3. Select the desired audio language in the list using the keys.4. Select the audio mode (mono, ...
Page 18 - Service List; Configuration Service
There are four service list types: All Service, Favourite Service,Network Service and Alphabetical Order Service.There is also a Configuration Service menu to change the attributes of each service in the list. In the service list, some buttons are used to switch the service listtype or select the se...
Page 19 - Service Network
Services can be grouped in the favourite list. To add a service to agroup in the favourite list, the Configuration Service box or theService Organising menu in the main menu can be used. (Refer to the related item for a more detailed description). To select the “Favourite Service” list, press the GR...
Page 20 - • Change PIN: the PIN code can be modified.; Main Menu Guide
GB19 The Main menu contains the TV Guide, Parental Control, Installationand Utility menus. (For more detailed information about menu structure, please refer to the Menu Map page at the end of theUser’s Manual.) The TV Guide is useful when all the services are being navigated,since it offers all poss...
Page 22 - Now mode
The NOW mode displays information on the present services and following services. The information includes service name,event name and start/end time of an event. To activate the NOW mode and surf the services, proceed as follows: 1. Activate the TV Guide menu using the GUIDE ( ) button or via the M...
Page 23 - To activate the WEEKLY mode, proceed as follows:; Activate the TV Guide menu using the GUIDE ( ) button or; To reserve a service event, proceed as follows:; Weekly mode
The WEEKLY mode displays information about all the services thatwill be transmitted over a week.The information includes service name, event name and start/endtime of the event. To activate the WEEKLY mode, proceed as follows: 1. Activate the TV Guide menu using the GUIDE ( ) button or via the Main ...
Page 24 - • Activate the TV Guide menu using the GUIDE ( ) button or; Next, change the mode or remove the event.
The RESERVED mode displays the services which have beenreserved.In this mode, the reservation mode can be changed. The service can also be removed from the reservation list. To change the mode or remove a service event of, proceed as follows in RESERVED mode: • Activate the TV Guide menu using the G...
Page 27 - Subtitle Language
The subtitle language is a language selected as a default when a service with subtitles is playing. It is also possible to changethe subtitle language via the Soundtrack menu in the Option Listmenu. To change the subtitle language, proceed as follows: 1. Activate the Language Setting menu via the Ma...
Page 28 - Sleep Time
To disable or enable/set the wake-up timer, proceed as follows: 1. Activate the Time Setting menu via the Main menu.2. Select the Wakeup Time item using the button.3. To disable the wake timer, set to “Disable” using the button. 4. To enable and set the wakeup timer, set the item to “00:00” using th...
Page 29 - • Configure the Audio output of RCA (Cinch) Jack as Mono or; Audio Output
Main Menu Guide The A/V Output Setting menu supplies menus that configure thefunctions related to Audio and Video output. • Configure the Audio output of RCA (Cinch) Jack as Mono or Stereo mode. • Configure the screen aspect ratio (4:3 or 16:9) of the TV connected to STB. • Configure the video displ...
Page 30 - To configure the display format on the TV, proceed as follows:; Display Format
To configure the display format on the TV, proceed as follows: 1. Activate the A/V Output Setting via the Main menu.2. Select the Display Format item using the button.3. Select the desired display format depending on the TV using the button. There are two mode pairs depending on the type of TV. If t...
Page 31 - NTSC Mode
Main Menu Guide To configure the NTSC mode on the TV, proceed as follows: 1. Activate the A/V Output Setting via the Main menu.2. Select the NTSC Mode item using the button.3. Select the desired NTSC Mode using the button.4. Press the OK ( ) or EXIT ( ) button to confirm. The UHF Tuning menu supplie...
Page 32 - -2 Service Organising; OSD Transparency
To set the OSD transparency, proceed as follows: 1. Activate the Other Setting menu via the Main menu.2. Select the OSD Transparency item using the button.3. Select the desired level between Opaque and Transparent modes using the button. 4. Press the OK ( ) or EXIT ( ) button to confirm. To set the ...
Page 33 - Organise All Services
Main Menu Guide The Organise TV services menu supplies two organisation methods: Organise All Services and Organise Favourites.Each offers a method of organisation with its own characteristics. The services are sorted according to the service number in theOrganise All Services menu.Each service can ...
Page 35 - Organise Favourite Services
The services are sorted according to favourite groups in theOrganise Favourites menu.There are three columns: the favourite group column, the favourite list column and the service list column containing services not belonging to any favourite group.The Organise Favourites menu supplies the following...
Page 40 - Organise Networks
The Organise Networks menu supplies the following functions: • Delete the network. This will delete all services belonging to the network. • Move/reorder the networks in the network list.• Sort the services according the network. In the Organise Networks menu, there are two columns: the networklist ...
Page 41 - Delete Satellites
Main Menu Guide The Delete Satellites menu supplies the following functions: • Delete a satellite. It will also delete all services belonging to the satellite. • Delete a transponder. It will also delete all services belonging to the transponder. • Sort the services according to the satellite and th...
Page 42 - Disables/enables the 22KHz tone in the signal line.; Antenna Setting
3-3. Service Searching The Antenna Setting menu sets the characteristics of each antenna.32 antennae can be supported, one of which for SMATV.The Antenna Setting menu supplies the following items to characterise the antenna. Assigns an index to each antenna. Hence, the value is unique foreach antenn...
Page 43 - Specifies the antenna used for searching.; Manual Search
Main Menu Guide The function of the Manual Search menu is to search services inone transponder using information from a satellite transponder. (If the Network Search option is enabled, services in other transponders are searched).The following items are supplied as parameters: Specifies the antenna ...
Page 45 - Guide of Main Menu; Automatic Search; The following items are supplied as parameters.; Antenna Alternative
Guide of Main Menu Automatic Search The function of the Automatic Search menu is to search servicesusing information from a satellite. The following items are supplied as parameters. Specifies the satellite in which the automatic search will be performed. Enables/disables the automatic skip option. ...
Page 46 - STB Status
3-4. Status The function of the Status menu is to supply users with information on several STB statuses, such as: • Information on the Software version,• Information on the Hardware version,• Information on the signal level of the current locked TP,• Information on OTA availability. This information...
Page 47 - To retrieve the information, proceed as follows:; and press the OK ( ) button to retrieve the information.
Main Menu Guide 3-5. Conditional Access The Conditional Access menu supplies information on IRDETO embedded CAS.There are four sub-menus in the menu: • Version Information,• Smart Card Information,• Transport Stream Information,• Monitoring ECM/EMM. The Version Information menu supplies technical in...
Page 49 - DiSEqC 1.2 User Instructions; Satellite Setting Menu Options; Motorised System
DiSEqC 1.2 User Instructions If you have a DiSEqC 1.2 motorised system, you can use the available DiSEqC 1.2 functions.The following instruction describes how to use the DiSEqC 1.2 functions to store the positions of thesatellites and search for the services (STAB Rotor Sat motor recommended). When ...
Page 50 - Initial Satellite Position Search; Motor Limit Setting
3. Initial Satellite Position Search This is required when you first set your receiver up to use DiSEqC 1.2, and sets the positions of allpre-programmed satellites. 1. Make sure your motor is installed correctly with the calibrations adjusted for the region in which you are located. (Please consult ...
Page 51 - Manual Satellite Search
6. To set the East Limit: a) Select “Movement” and use the buttons to move your motor East or West until it is at the position you wish to use as your East Limit. Use the buttons to stop the motor at the correct position. b) Highlight the Store East Limit option and press the OK ( ) button to store ...
Page 52 - Searching for services on your selected Satellite
Once you have stored the positions of the satellites you want (see below left) you can search for theservices transmitted from them. Before doing this, you must move the motor to the position of thesatellite you wish to search for. To do this, you must access the Satellite Settings menu. Proceed asf...
Page 54 - Troubleshooting Guide
Page 55 - Menu Map
Page 57 - Transport Stream; Specification
Tuner & Channel Conditional Access Interface MPEG Transport Stream A/V Decoding Memory Input ConnectorFrequency RangeInput ImpedanceSignal LevelIFIF Band widthLNB Power &Polarisation 22 KHz ToneDiSEqC ControlDemodulationInput Symbol RateFEC Decode Transport Stream Profile LevelInput RateAspe...
Page 58 - VIDEO; Physical Specifications; • You can use a special antenna switch with DiSEqC commands.
A/V & Data In/Out VIDEO AUDIO R/L RS-232C RCA / CinchVideo Output (CVBS) RCA/Cinch Volume and Mute Control(Resolution : 20 bits DAC, Max. 2 Vrms)Transfer rate 115,200 bps, 9pin D-sub Type Physical Specifications Size (W x H x D) Weight (Net)Operating TempStorage TempStorage Humidity 260 x 50 x 1...
